Related Manuals for Toro SGR-6 22600
Summary of Contents for Toro SGR-6 22600
- Page 1 Form No. 3386-286 Rev A SGR-6 Stump Grinder Model No. 22600—Serial No. 314000001 and Up G025787 *3386-286* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Introduction
You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register DANGER your product. -
Page 3: Table Of Contents
Safety Improper use or maintenance by the operator or owner Figure 2 can result in injury. To reduce the potential for injury, comply with these safety instructions and always 1. Safety alert symbol pay attention to the safety alert symbol , which means: Caution , Warning , or Danger —personal safety instruction. - Page 4 Make any necessary repairs before restarting. maneuver the product. • Use only genuine Toro replacement parts to ensure that • Before grinding, have the area marked for underground original standards are maintained.
-
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 117–4979 1. Entanglement hazard, belt—stay away from moving parts, keep all guards and shields in place. -
Page 6: Product Overview
Product Overview g014871 Figure 4 1. Handle-release knob Fold the handle down toward the machine and screw the knob back onto the handle (Figure 5). G025789 Figure 3 1. Handle 8. Starter 2. Throttle lever 9. Cutting wheel 3. Handle-release knob 10. -
Page 7: Specifications
A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. g014872 Figure 7 1. -
Page 8: Operation
Operation DANGER In certain conditions, gasoline is extremely Note: Determine the left and right sides of the machine flammable and highly explosive. A fire or explosion from the normal operating position. from gasoline can burn you and others and can damage property. -
Page 9: Checking The Engine-Oil Level
because the fuel system could be damaged. Do not mix 6. Wipe up any gasoline that may have spilled. oil with gasoline. Checking the Engine-Oil Level Using Stabilizer/Conditioner Service Interval: Before each use or daily Use a fuel stabilizer/conditioner in the machine to provide the following benefits: 1. -
Page 10: Starting And Stopping The Engine
Starting and Stopping the Grinding a Stump Engine DANGER The machine will cut and amputate hands and feet. Starting the Engine • Stay in the operator's position while the machine 1. Move the fuel valve to the Open position, all the way is running and keep away from the cutting to the right (Figure 11). - Page 11 Figure 13 G025887 Figure 12 6. Raise the cutting wheel, release the parking brake, 1. Pivot point 2. Pivot point when the and move the machine forward a few inches. Set the parking brake is engaged. parking brake. 7. Repeat steps 5 and 6 until you have completely 3.
-
Page 12: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Important: The machine may be tipped backward or on its side to facilitate access for cleaning or service, but no longer than 2 minutes. If the machine is held in this position for too long, the engine can be damaged by gasoline draining into the crankcase. -
Page 13: Servicing The Engine Oil
4. Place the air channels in the cyclone housing. 4. Tap the paper filter against a fixed surface to remove dust. If the paper filter is still dirty or damaged, replace 5. Insert cyclone housing into position and make sure it fits in the upper portion. -
Page 14: Servicing The Spark Plug
Note: Dispose of the used oil at a certified recycling gapping tool/feeler gauge to check and adjust the air gap. center. Install a new spark plug if necessary. 7. Remove the oil fill cap and slowly pour approximately Type: BPR6ES (NKG) or equivalent 80 percent of the specified amount of oil into the Air Gap: 0.70-0.80 mm (0.28–0.031 inch) engine (Figure 16). -
Page 15: Belt Maintenance
Installing the Spark Plug Belt Maintenance 1. Thread the spark plug into the spark plug hole. Checking the Drive Belt 2. Tighten the spark plug to 20 ft-lb (27 N-m). 3. Push the wire onto the spark plug. Tension Service Interval: Every 25 hours Note: Replace the belt if it shows any signs of wear, cracks, or damage. -
Page 16: Grinder Maintenance
Grinder Maintenance Replacing the Teeth Service Interval: Before each use or daily—Check the condition of the teeth and rotate or replace any that are worn or damaged. Due to the high amount of wear placed on the teeth, you will need to rotate and replace them periodically. -
Page 17: Cleaning
Cleaning Storage Storing the Machine Removing Debris from the Machine For storage over 30 days, prepare the unit as follows: 1. Remove dirt and grime from the external parts of Regular cleaning and washing will increase the life span of the entire unit, especially the engine. -
Page 18: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine will not start. 1. The engine switch is in the Off position. 1. Hold the safety bail against the handle. 2. The fuel shutoff valve is closed. 2. Open the fuel valve. 3. - Page 19 Notes:...
- Page 20 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.