Mitsubishi Electric FX5 User Manual page 418
Melsec iq-f series
Hide thumbs
Also See for FX5:
- Programming manual (1112 pages) ,
- User manual (958 pages) ,
- Reference manual (44 pages)
Table of Contents
Advertisement
Error
Error name
code
3628H
Axis 8 limit
detection error
3629H
Axis 9 limit
detection error
362AH
Axis 10 limit
detection error
362BH
Axis 11 limit
detection error
362CH
Axis 12 limit
detection error
3631H
Axis 1 positioning
address error
3632H
Axis 2 positioning
address error
3633H
Axis 3 positioning
address error
APPX
416
Appendix 3 Error Code
Error details and cause
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• Both the forward and reverse limits were
detected at the time of zero return or the
limit of the moving direction was detected
after the near-point dog was detected.
• The 32-bit range was exceeded when
the unit of the positioning address was
converted.
• The 32-bit range was exceeded when
the unit of the zero-point address was
converted.
• The total transfer distance before and
after the interrupt of the DVIT/DDVIT
instruction or 1-speed positioning with
interruption exceeded 7FFFFFFFH. Or,
when the operation was started, the
positioning address was set to 0.
• Pulses of 7FFFFFFFH or greater are
needed to specify an absolute address.
• The 32-bit range was exceeded when
the unit of the positioning address was
converted.
• The 32-bit range was exceeded when
the unit of the zero-point address was
converted.
• The total transfer distance before and
after the interrupt of the DVIT/DDVIT
instruction or 1-speed positioning with
interruption exceeded 7FFFFFFFH. Or,
when the operation was started, the
positioning address was set to 0.
• Pulses of 7FFFFFFFH or greater are
needed to specify an absolute address.
• The 32-bit range was exceeded when
the unit of the positioning address was
converted.
• The 32-bit range was exceeded when
the unit of the zero-point address was
converted.
• The total transfer distance before and
after the interrupt of the DVIT/DDVIT
instruction or 1-speed positioning with
interruption exceeded 7FFFFFFFH. Or,
when the operation was started, the
positioning address was set to 0.
• Pulses of 7FFFFFFFH or greater are
needed to specify an absolute address.
Action
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Recheck the relationship between the near-
point dog and limits.
• Start the positioning within specifications.
• Start the positioning within specifications.
• Start the positioning within specifications.
Detailed
Diagnostic
information
timing
Error location
At END
information
instruction
and system
execution, at
configuration
instruction
information
execution
Error location
At END
information
instruction
and system
execution, at
configuration
instruction
information
execution
Error location
At END
information
instruction
and system
execution, at
configuration
instruction
information
execution
Error location
At END
information
instruction
and system
execution, at
configuration
instruction
information
execution
Error location
At END
information
instruction
and system
execution, at
configuration
instruction
information
execution
Error location
At END
information
instruction
and system
execution, at
configuration
interrupt
information
occurrence
Error location
At END
information
instruction
and system
execution, at
configuration
interrupt
information
occurrence
Error location
At END
information
instruction
and system
execution, at
configuration
interrupt
information
occurrence
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric FX5
Related Products for Mitsubishi Electric FX5
- Mitsubishi Electric MELSEC iQ-F FX5U
- Mitsubishi Electric MELSEC iQ-F FX55-ASL-M
- Mitsubishi Electric MELSEC iQ-F FX5UC-96MT/D
- Mitsubishi Electric MELSEC iQ-F FX5UC-64MT/DSS
- Mitsubishi Electric MELSEC iQ-F FX5UC-32MT/D
- Mitsubishi Electric MELSEC iQ-F FX5UC-32MT/DSS
- Mitsubishi Electric MELSEC iQ-F FX5UC-96MT/DSS
- Mitsubishi Electric MELSEC iQ-F FX5UC-64MT/D
- Mitsubishi Electric MELSEC iQ-F FX5UC-32MT/DS-TS
- Mitsubishi Electric MELSEC iQ-F FX5UC-32MT/DSS-TS
- Mitsubishi Electric FX5-ENET
- Mitsubishi Electric FX5-DP-M
- Mitsubishi Electric MELSEC iQ-F FX5UC Series
- Mitsubishi Electric Melsec iQ-F FX5-C32EYT Series
- Mitsubishi Electric Melsec iQ-F FX5-C32ET TS Series
- Mitsubishi Electric Melsec iQ-F FX5-C16EYR/D-TS