The Power Reset means that you pull out the power source and pull in it again. Fig. 1-2 - : - - : - - : - VCRADJ Indicates current adjustment item Indicates the adjusted values Indicates preset values Fig. 1-3 Samsung Electronics...
Page 70
SWP Position Head Switching Position Adjust 1) How to adjust Head Switching Position Œ Get into VCR ADJUST mode. ´ Move to the VCR ADJUST address “437”. ˇ Play standard tape, and “Head Switching Position” will be adjusted automatically. Samsung Electronics...
Page 71
´ Press the push the “ENTER” when storing confirmed adjustment value of each adjustment step in EEPROM. ˇ The OSD shows “OK” after finishing each adjustment step. ¨ To clear the adjustment mode, pull out the power source. Samsung Electronics...
Page 72
PRML ADJ Ø After setting adjustment value, please push the CAM DISP “ENTER” to confirm Data. DSC ADJ STEP 3 LCD/CVF ADJ CAMERA Monitor OSD shows " ". Then camera adjustment mode has been activated successfully. Fig. 2-2 Samsung Electronics...
Page 73
ˆ Press the “EASY”(Mode Up)/”DISPLAY”(Mode Down) buttons so that OSD shows "ODE XX XX". Ø Press the “ENTER” (Confirm). Never impact on the lens when adjusting zoom and focus Lens. The OSD shows “OK” after finishing the adjustment. 3M ± 1cm (Be sure to maintain the distance) LENS Fig. 2-4 Samsung Electronics...
Page 74
¨ Ensure that camera picks up image 40 µs on 5100 gray scale chart (3100 gray scale chart + C16 filter) precisely and the illumination is 1500~2000 Lux. ˆ Press the “ENTER” (Confirm) to ensure that white spot on a vectorscope is moving in the middle of screen. Ø The OSD shows “OK” after finishing the adjustment. Samsung Electronics...
Page 75
DISPLAY (Mode Down) Shift adjustment address to right. MENU Dial up (Data Up) Up value. MENU Dial down (Data Down) Down value. Note : In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics...
1) Set the power-supply output to approx.3V. <Table 4-1> 2) Choose the polarity (depending on whether load- Movement of chassis ing or unloading). Loading 3) Supply the voltage to the Motor Loading, and set to the desired mode. Unloading DC POWER SUPPLY Fig. 4-2 Samsung Electronics...
Page 78
Œ In EJECT mode, clean the tape path system(from Pole Tension P1 through Pole Review P7, Pinch Roller and Capstan Shaft) and the Lower Drum. Using the lens tissue soaked in ethyl alcohol. Note : Make sure that no oil or grease adheres to the lens tissue. PINCH ROLLER Fig. 4-3 Samsung Electronics...
Page 79
(Oil contaminated with dust might cause the bearings to wear out or seize.) ◆ A “drop”of oil is defined as the amount attached to the tip of a Ø 2mm stick as shown in Fig. 4-4. Fig. 4-4 Samsung Electronics...
Page 80
(If it is located outside, adjust toward arrow B.) Note : Check if the Arm Tension can be moved toward arrow C in PB mode. 3) Reassembly Œ For the removal of the Housing Ass’y. ± 1 0.3 ARM TENSION CAP ADJUSTMENT Fig. 4-5 Samsung Electronics...
Page 81
Œ For the removal of the Idler Ass’y. ´ For the removal of the Housing Ass’y. ± A, B : 3.9 0.1mm REEL DISK S TABLE REEL DISK T TABLE RESTING SURFACE RESTING SURFACE CHASSIS SUB Fig. 4-6 Samsung Electronics...
¨ Check that the waveform of the RF signal is flatat both inlet and outlet(A in Fig. 4-7). If not flat (B or C in Fig. 4-7), do adjustments 4-5(b) through 4-5(d). INLET OUTLET NORMAL DEFECT AT INLET DEFACT AT OUTLET Fig. 4-7 S REEL T REEL Fig. 4-8 Samsung Electronics...
Page 83
´ Set to REV mode and observe the outlet waveform of PB RF signal. (Fig. 4-11) ˇ If the outlet waveform is out-of-spec, turn P7 counterclockwise, and redo steps 1 and 2. CAPSTAN P5 Fig. 4-11 Fig. 4-10 Samsung Electronics...
Page 84
If the track pitch is not uniform, do section 4-5(b) (Tracking adjustment) and 4-5(c) (P7 adjustment). ´ Set to CUE mode. Confirm that the waveform peaks still have a uniform pitch. (Fig. 4-14 B) If the track pitch is not uniform, do section 4-5(b) (Tracking Adjustment). Fig. 4-14 Samsung Electronics...
Page 85
Œ In CUE and REV modes, check that the tape is not curled around the P1, P3, P5 upper flange and P7 upper/Lower flanges. P7 CAPSTAN P5 Fig. 4-15 FROM THE S REEL FROM THE T REEL Fig. 4-16 Samsung Electronics...
Page 86
Alignment and Adjustments MEMO 4-10 Samsung Electronics...