Cisco ASR 1013 Hardware Installation Manual page 419
Asr 1000 series
Hide thumbs
Also See for ASR 1013:
- Installation manual (42 pages) ,
- Quick start manual (37 pages) ,
- Replacing (120 pages)
Table of Contents
Advertisement
Cisco ASR 1013 Router Overview and Installation
Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches
Note
(48.26 cm). The height of the chassis is 22.75 inches (57.8 cm). Airflow through the chassis is from front
to back.
Make sure the rack is stabilized.
Note
SUMMARY STEPS
1. (Optional) Install a shelf in the rack to support the Cisco ASR 1013 Router. If you are using a shelf then
raise the chassis to the level of the shelf. Let the bottom of the chassis rest on the brackets, but continue
to support the chassis.Using two people, lift the chassis into the rack using the side handles and grasping
underneath the power supply bays.
2. Position the chassis until the rack-mounting flanges are flush against the mounting rails on the rack.
3. Hold the chassis in position against the mounting rails while the second person finger-tightens a screw to
the rack rails on each side of the chassis.
4. Finger-tighten 4 more screws to the rack rails on each side of the chassis.
5. Tighten all screws on each side to secure the chassis to the equipment rack.
6. Use a level to verify that the tops of the two brackets are level, or use a measuring tape to verify that both
brackets are the same distance from the top of the rack rails.
DETAILED STEPS
Step 1
(Optional) Install a shelf in the rack to support the Cisco ASR 1013 Router. If you are using a shelf then raise the chassis
to the level of the shelf. Let the bottom of the chassis rest on the brackets, but continue to support the chassis.Using two
people, lift the chassis into the rack using the side handles and grasping underneath the power supply bays.
Step 2
Position the chassis until the rack-mounting flanges are flush against the mounting rails on the rack.
Note
Use the third hole up from the bottom of the rack-mount bracket and the third hole down from the top of the
rack-mount bracket. See "Cable-Management Brackets Installed on the Cisco ASR 1013 Router" figure in the
Attaching the Cable-Management Bracket section for position and location of the ear holes on the rack-mount
bracket.
Step 3
Hold the chassis in position against the mounting rails while the second person finger-tightens a screw to the rack rails
on each side of the chassis.
Step 4
Finger-tighten 4 more screws to the rack rails on each side of the chassis.
Step 5
Tighten all screws on each side to secure the chassis to the equipment rack.
Step 6
Use a level to verify that the tops of the two brackets are level, or use a measuring tape to verify that both brackets are
the same distance from the top of the rack rails.
What to Do Next
This completes the procedure for installing the chassis in the rack. Proceed to the
Cable-Management Bracket, on page 386
to continue the installation.
Cisco ASR 1000 Series Router Hardware Installation Guide
Four-Post Rack Installation
Attaching the
385
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Cisco ASR 1013
Related Products for Cisco ASR 1013
- Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1 Router
- Cisco ASR1000-RP2 - ASR 1000 Series Route Processor 2 Router
- Cisco ASR1002-5G-SEC/K9 - ASR 1002 VPN+FW Bundle Router
- Cisco ASR1002-5G-SHA/K9 - ASR 1002 Sec+HA Bundle Router
- Cisco ASR1004-10G-SHA/K9 - ASR 1004 Sec+HA Bundle Router
- Cisco ASR1004-20G-SEC/K9 - ASR 1004 VPN+FW Bundle Router
- Cisco ASR1006-10G-SEC/K9 - ASR 1006 VPN+FW Bundle Router
- Cisco ASR1006-10G-VPN/K9 - ASR 1006 VPN Bundle Router