Configuring Frf.12 - Cisco ASR 1000 Series Software Configuration Manual
Aggregation services routers sip and spa, cisco ios xe everest 16.5
Hide thumbs
Also See for ASR 1000 Series:
- Configuration manual (442 pages) ,
- Replacing (120 pages) ,
- Common criteria operational user guidance and preparative procedures (72 pages)
Table of Contents
Advertisement
Configuring the 1-Port Channelized OC-3/STM-1 SPA and 1-Port Channelized OC-12/STM-4 SPA
Total Data (last 73 15 minute intervals):
Configuring FRF.12
The 1-Port Channelized OC-3/STM-1 SPA and 1-Port Channelized OC-12/STM-4 SPA support FRF.12
end-to-end fragmentation for Frame Relay. For information about how to configure Frame Relay fragmentation
support, see the "Frame Relay Queueing and Fragmentation at the Interface" chapter of the Cisco IOS XE
Wide-Area Networking Configuration Guide , Release 2 at:
http://www.cisco.com/en/US/docs/ios/ios_xe/wan/configuration/guide/wan_frque_frag_if_xe.html
Configuring Multilink Point-to-Point Protocol (Hardware-Based on the QFP)
Multilink Point-to-Point Protocol (MLPPP) allows you to combine interfaces which correspond to an entire
T1 or E1 multilink bundle. You can choose the number of bundles and the number of T1 or E1 lines in each
bundle in any combination of E1, T1, and NxDS0 member links interfaces.
On the Cisco ASR 1000 Series Router, MLPPP functionality is implemented on the Quantum Flow Processor
(QFP)—not the SPA. On other platforms that implement SPA-based MLPPP, the MLPPP member links must
reside on the same SPA—this is not a restriction on the Cisco ASR 1000 Series Aggregation Services Routers.
QFP-based MLPPP supports member links in the MLPPP bundle across different SPAs and SIPs on the Cisco
ASR 1000 Series Aggregation Services Routers.
For more information about configuring MLPPP in Cisco IOS XE software, see the
Media-Independent PPP and Multilink PPP"
Guide, Release 2
This section includes the following topics:
MLPPP Configuration Guidelines
When configuring MLPPP, consider the following guidelines:
• Only T1, E1, or NxDS0 links are supported in a bundle. The configuration will not prohibit higher
• Links of differing bandwidths are supported in the same bundle.
• PPP encapsulation must be enabled before configuring multilink-related commands.
Creating a Multilink Bundle
To create a multilink bundle, use the following commands:
SUMMARY STEPS
1. Router# configure terminal
2. Router(config)# interface multilink group-number
3. Router(config-if)# ip address address mask
OL-14127-17
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
1278491 Line Code Violations, 3 Path Code Violations,
0 Slip Secs, 1 Fr Loss Secs, 177 Line Err Secs, 0 Degraded Mins,
3 Errored Secs, 0 Bursty Err Secs, 1 Severely Err Secs, 227 Unavail Secs
.
bandwidth links from being added to the bundle, but they are not supported.
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS XE
chapter of the
Cisco IOS XE Wide-Area Networking Configuration
Optional Configurations
"Configuring
Everest 16.5
309
Advertisement
Chapters
Table of Contents
Troubleshooting
