Mitsubishi Electric MELSERVO-J5 User Manual page 269
Ac servo system
Hide thumbs
Also See for MELSERVO-J5:
- User manual (580 pages) ,
- Sample screen manual (128 pages) ,
- Introduction manual (112 pages)
Table of Contents
Advertisement
■Source I/O interface (CN9, CN10 connectors)
• Digital input interface DI-1
This is an input circuit in which the anode of the photocoupler is the input terminal. Transmit signals from a source (open-
collector) type transistor output, relay switch, etc.
Switch
Approximately
24 V DC ± 10 %
5 mA
200 mA
V
≤ 1.0 V
CES
I
≤ 100 μA
CEO
• Digital output interface DO-1
This is a circuit in which the emitter of the output transistor is the output terminal. When the output transistor is turned on, the
current flows from the output terminal to a load.
A maximum of 2.6 V voltage drop occurs in the MR-J3-D05.
MR-J3-D05
SDO2B+,
etc.
SDO2B-,
etc.
*1 If the voltage drop (maximum of 2.6 V) interferes with the relay operation, apply high voltage (maximum of 26.4 V) from external source.
Wiring CN9, CN10 connectors
Be careful when handling tools during wiring work.
■Stripping wire
• Use wire of applicable wire size from AWG 24 to 20 (0.22 mm
and process it so that its stripped length is 7.0 mm ± 0.3 mm. Before using, be sure to check the length of the stripped
section with a gage or other tool.
• If the stripped wire is bent, frayed, or wound too thick, correct it by lightly twisting the wire or manipulating it as necessary,
and check the length of the stripped section before using it. In addition, do not use excessively deformed wire.
• When processing the cut surface of wire and the stripped surface of conductor, make them smooth.
■Connecting wires
When connecting wires, do so with the receptacle assembly pulled out of the head connector. Wiring while connectors are
inserted in the servo amplifier may damage the connectors or the board.
• Connecting wires with insertion/extraction tool (1891348-1 or 2040798-1)
Dimensions and mass
100
MR-J3-D05
SRESA-,
etc.
Approx. 5.4 kΩ
SRESA+,
etc.
If polarity of diode is
reversed, MR-J3-D05
will malfunction.
Load
*1
24 V DC ± 10 %
200 mA
[Unit: mm]
7
15
Mass: Approx. 20 g
2
2
to 0.5 mm
) (recommended wire: UL 1007 recommended),
6 OPTIONS AND PERIPHERAL EQUIPMENT
6.17 MR-J3-D05 safety logic unit
6
267
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric MELSERVO-J5
Related Products for Mitsubishi Electric MELSERVO-J5
- Mitsubishi Electric Melservo-J2-JR SERIES
- Mitsubishi Electric Melservo-J3 Series MR-J3-B
- Mitsubishi Electric MELSERVO-J4 series
- Mitsubishi Electric MELSERVO-J2-Super Series
- Mitsubishi Electric MELSERVO-J2M series
- Mitsubishi Electric MELSERVO-JE
- Mitsubishi Electric MELSERVO-JE MR-JE-C
- Mitsubishi Electric MELSERVO-J3W Series
- Mitsubishi Electric Melservo-J5 MR-J5 Series
- Mitsubishi Electric MELSERVO-J5 MR-J5-G-N1
- Mitsubishi Electric MELSERVO-J2 Series
- Mitsubishi Electric MELSERVO-J4 MR-J4 TM
- Mitsubishi Electric MELSERVO-J4 MR-J4-11KTM
- Mitsubishi Electric MELSERVO-J4 MR-J4-11KTM4
- Mitsubishi Electric MELSERVO-J4 MR-J4-22KTM
- Mitsubishi Electric MELSERVO-J4 MR-J4-22KTM4