Related Manuals for Toro Reelmaster 33455
Summary of Contents for Toro Reelmaster 33455
- Page 1 Form No. 3434-992 Rev A Transport Frame Reelmaster ® Model No. 33455—Serial No. 405700000 and Up *3434-992* Register at www.Toro.com. Original Instructions (EN)
- Page 2 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 General Safety General Safety ........... 3 Safety and Instructional Decals ......4 • Read and understand the contents of both this Setup ................ 5 Operator’s Manual and the operator’s manual of 1 Preparing the Tow Vehicle........ 7 the tow vehicle before using this machine. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal133-8061 133-8061 decal137-6138 137-6138 1. Valve control lever—raise 3. Warning—do not exceed 32 km/h (20 mph). 2. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the tow vehicle. Hitch Pin Adjust the transport frame hitch. Hairpin Cotter Lower tower Upper tower Capscrew (3/8 x 2-3/4 inch) Install the control tower. - Page 6 Media and Additional Parts Description Qty. Operator’s Manual Read this manual before using the transport frame. Parts Catalog Review the material and save in an appropriate place. Declaration of conformity Certificate of compliance Note: Determine the left and right sides of the machine from the normal operating position.
-
Page 7: Preparing The Tow Vehicle
Recommended replacement fluid: Toro Premium Transmission/Hydraulic Tractor Fluid; available in 19 L (5 US gallon) pails or 208 L (55 US gallon) drums. Alternative fluids: If Toro Premium Tractor Fluid is not available, you may use other conventional, petroleum-based Universal Tractor Hydraulic g012750... -
Page 8: Installing The Control Tower
position. Install the ball pin to secure it in the storage position (Figure 16). Adjusting the Transport Frame Hitch Installing the Control Tower Parts needed for this procedure: Hitch Pin Parts needed for this procedure: Hairpin Cotter Lower tower Upper tower Procedure Capscrew (3/8 x 2-3/4 inch) Measure the height from the ground to the top... -
Page 9: Mounting The Control Linkage And Levers
Adjust the control tower forward or backward by Secure the upper control linkage tubes to the sliding the tower on the center frame tube and pivot blocks with the clevis pins and cotter pins tightening the flange nuts and U-bolts. (Figure Coat the clevis pins with No. - Page 10 Note: in toward the valve, or pulling them out to find The lever on the control tower should be the mid position. in the center of the slot (neutral position) if the control rods are adjusted correctly (Figure 11). Coat all pivot points with No. 2 lithium grease or lubricate them with 30 SAE oil.
-
Page 11: Connecting The Supply/Return Hoses To The Tow Vehicle
Note: If you are attaching Spartan mowers, draw bar clamps (Part no. 5-1090) and mounting fasteners are required to mount the draw bar to the front cross tube of the mower. Contact your local authorized Toro distributor for assistance. -
Page 12: Checking The Tire Air Pressure
Secure the lift bracket to #1 lift chain (rear center) with a long shackle, clevis pin, and cotter (Figure 13). Note: Ensure that there are no kinks or twists in the chain before installing the cutting units. g012763 Figure 14 g012762 Figure 13 1. -
Page 13: Product Overview
Product Overview Controls Transport Frame Controls Control Levers The controls are conveniently located on the control tower at the front of the frame. g001055 Figure 15 Hold the lever(s) in their respective positions until the cycle is completed, then return the lever(s) to neutral. •... -
Page 14: Specifications
• Auxiliary valve operation To ensure optimum performance and continued safety • Clutch certification of the machine, use only genuine Toro replacement parts and accessories. Replacement • Throttle parts and accessories made by other manufacturers • Gear selection could be dangerous, and such use could void the product warranty. -
Page 15: Before Operation
Operation Remove the pin from the jack and storage tube (Figure 16). Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Before Operation Safety General Safety • Never allow children or untrained people to operate or service the machine. -
Page 16: During Operation
Stowing the Jack • Reduce speed when operating on rough, uneven terrain, and near curbs, holes, and other sudden Ensure that the transport frame is securely changes in terrain. attached to the tow vehicle. • To avoid causing the machine to tip over, be Rotate the jack handle to fully raise the jack pad;... -
Page 17: After Operation
Consult the mower operators manual for proper overall efficiency. Mowing at 6.4 to 9.7 km/h (4 adjustment procedures. to 6 mph) produces the finest turf appearance. When arriving at area to be mowed, remove Reverse the direction of travel each time an safety strap and lockup pins and approach area area is mowed. -
Page 18: Raising The Mowers To The Transport Position
• Always inspect the hitch and coupling for wear. Do not tow the machine with damaged or missing hitches or couplings. • Avoid sudden stops and starts. This can cause skidding or jack knifing. Smooth, gradual starts and stops will improve towing. •... -
Page 19: Inspection And Clean-Up After Mowing
lockup bracket and secure to cylinder rest with hairpin cotter (Figure 21). Inspection And Clean-up After Mowing At the completion of mowing operation, thoroughly wash the machine with a garden hose without a nozzle so excessive water pressure will not cause contamination and damage to seals and bearings. -
Page 20: Maintenance
• Altering this machine in any manner may affect the operation of the machine, performance, durability, or its use may result in injury or death. Such use could void the product warranty of The Toro® Company. g012770 Figure 24... - Page 21 g012771 Figure 25 g012774 Figure 27 g012773 Figure 26 g012775 Figure 28 g337510 Figure 29 Oiling the Wear and Friction Points Lightly oil wear or friction points whenever grease fittings are being serviced.
-
Page 22: Changing The Hydraulic Fluid
g012768 Figure 30 g012779 Figure 33 Changing the Hydraulic Fluid Drain and replace the transport frame hydraulic fluid whenever the tow vehicle fluid is changed, if the fluid is not compatible with the tow vehicle fluid, or if the fluid becomes contaminated. Start the tow vehicle, remove all cutting units, raise the lift arms until all lift cylinders are fully retracted, and then shut off the tow vehicle. -
Page 23: Replacing The Wheel Bearings
Start the tow vehicle and cycle the lift arms up and down at least 2 full cycles. Check the hydraulic-fluid level with the lift arms raised and add fluid if needed. Install the cutting units. Replacing the Wheel Bearings Jack up the wheel being serviced. Support with jack stand to prevent it from falling. -
Page 24: Replacing The Lift-Arm Bushing
Reinstall the hub caps. Replacing the Lift-Arm Bushing Position lift arm in the down position. Remove the cutting unit. Remove the nut from the end of the pin (Figure 36). g012778 Figure 36 1. Lift arm 4. Capscrew 2. Nut 5. -
Page 25: Schematics
Schematics g337511 Hydraulic Schematic (Rev. A) - Page 26 Notes:...
- Page 27 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.