Related Manuals for Lenovo ideapad 330 Series
Summary of Contents for Lenovo ideapad 330 Series
- Page 1 Lenovo ideapad 330 ideapad 330-17AST ideapad 330-17AST D ideapad 330-17AST U ideapad 330E-17AST D ideapad 330E-17AST U ideapad 330H-17AST ideapad 330L-17AST ideapad 330E-17AST ideapad 330R-17AST Hardware Maintenance Manual...
- Page 2 Note: • Before using this information and the product it supports, be sure to read the general information under “Notices” on page 74. First Edition (April 2018) © Copyright Lenovo 2018. All rights reserved. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. © 2018 Lenovo...
-
Page 3: Table Of Contents
Power-on password ..........24 Hard-disk password ..........24 Administrator password ........24 Power management ........25 Putting the computer to sleep or shutting it down ..............25 Putting your computer to sleep ......25 Shutting down the computer ......26 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ideapad 330E-17AST D/ ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ ideapad 330R-17AST .........27 Specifications ..........27 Status indicators ........... 29 Hotkeys............30 FRU replacement notices ...... -
Page 4: About This Manual
• The product-specific section includes service, reference, and product-specific parts information. Important: This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo product, make sure to read all the information under “Safety information” on page 1 and “Important service information” on page 16. -
Page 5: Safety Information
Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo ideapad 330-17AST/ideapad 330- 17AST D/ideapad 330-17AST U/ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST computer: • “General safety” on page 2 • “Electrical safety” on page 3 • “Safety inspection guide” on page 5 • “Handling devices that are sensitive to electrostatic discharge” on page 6 • “Grounding requirements” on page 6... -
Page 6: General Safety
Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: • Observe a good housekeeping in the area where the machines are put during and after the maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4. Lift it by standing or pushing up with your leg muscles; this action could avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you. • Do not perform any action that causes hazards to the customer, or that makes the machine unsafe. -
Page 7: Electrical Safety
Safety information Safety information Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. - Page 8 Hardware Maintenance Manual • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. • Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Caution: do not become a victim yourself. – Switch off the power. – Send the victim to get medical aid.
-
Page 9: Safety Inspection Guide
The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn. 4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 8. Check for worn, frayed, or pinched cables. -
Page 10: Handling Devices That Are Sensitive To Electrostatic Discharge
Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1. Use product-specific ESD procedures when they exceed the requirements noted here. 2. -
Page 11: Safety Notices: Multilingual Translations
Safety information Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. - Page 12 Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short- circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing.
- Page 13 Safety information Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
- Page 14 Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations.
- Page 15 Safety information Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à...
- Page 16 Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
- Page 17 Safety information Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
-
Page 18: Laser Compliance Statement
Hardware Maintenance Manual Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products. - Page 19 Safety information A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
-
Page 20: Important Service Information
Strategy for replacing FRUs Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://support.lenovo.com. 2. Enter the serial number or select a product or use Lenovo smart downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software. -
Page 21: Strategy For Replacing A Hard Disk Drive
Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: • If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. • Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one. • If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect. -
Page 22: Important Information About Replacing Rohs Compliant Frus
Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. -
Page 23: General Checkout
General checkout General checkout This chapter presents the following information: • “What to do first” on page 20 • “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • Carefully remove screws for reuse when replacing FRUs. • Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered. -
Page 24: What To Do First
Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8. Customer’s name and address Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. -
Page 25: Power System Checkout
You are here because the computer fails only when the AC adapter is used. • If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity and installation. • If the computer does not charge during operation, go to “Checking operational charging”. To check the AC adapter, follow the steps below: 1. Unplug the AC adapter cable from the computer. 2. Measure the output voltage at the plug of the AC adapter cable. See the following figure: Voltage (V DC) Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing. 3. If the voltage is not correct, replace the AC adapter. 4. If the voltage is acceptable, do the following: • Replace the system board. • If the problem persists, go to “Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST” on page 27. Note: Noise from the AC adapter does not always indicate a defect. -
Page 26: Checking Operational Charging
Hardware Maintenance Manual Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack. If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section. Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life. To check your battery, move your cursor to the Power Meter icon in the icon ®... -
Page 27: Related Service Information
Push-button reset System. In order to save application files and the initial backed up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, press the Novo button and run System Recovery. For details of Push-button reset System, see the Recovery system in the User Guide. -
Page 28: Passwords
Hardware Maintenance Manual Passwords As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the administrator password. If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered. -
Page 29: Power Management
Related service information Power management Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has two power management modes: sleep (standby), and hibernation. Putting the computer to sleep or shutting it down When you have finished working with your computer, you can put it to sleep or shut it down. Putting your computer to sleep If you will be away from your computer for only a short time, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process. To put the computer to sleep, do one of the following: • Close the display lid. • Press the power button. -
Page 30: Shutting Down The Computer
Hardware Maintenance Manual Shutting down the computer If you are not going to use your computer for a long time, shut it down. To shut down your computer, do one of the following: • Select the Start button, then select Power → Shut down. • Right-click or press the Start button in the lower-left corner and select Shut down or sign out → Shut down. -
Page 31: Ideapad 330R-17Ast
• “Hotkeys” on page 30 • “FRU replacement notices” on page 31 • “Removing and replacing an FRU” on page 32 • “Locations” on page 63 • “Parts list” on page 65 Specifications The following table lists the specifications of the Lenovo ideapad 330- 17AST/ideapad 330-17AST D/ideapad 330-17AST U/ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ideapad 330L-17AST/ ideapad 330E-17AST/ideapad 330R-17AST: Table 1. Specifications Form Factor Dimensions Appr. 418 mm × 292.6 mm × 24.9 mm... - Page 32 Hardware Maintenance Manual Table 1. Specifications (continued) Hard disk drive Form factor 2.5-inch, 7 mm Capacity HDD: 500 GB / 1 TB / 2 TB, 5400 rpm Interface SATA 2/SATA 3 Optical Drive (on select models) Form factor 9.0 mm Type Writer Display Display resolution 1600 × 900 pixels HD/1920 × 1080 pixels FHD (LCD) LCD backlight I/O Ports USB 3.0 × 1, USB 2.0 × 1 Audio Combo audio jack × 1 Video/Audio HDMI slot × 1 Ethernet RJ-45 × 1 Memory card slot 4 in 1 slot × 1 (SD/SDHC/SDXC/MMC) Battery pack Type...
-
Page 33: Status Indicators
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Status indicators The system status indicators below show the computer status: Table 2. Status indicators AC power Indicator status Meaning adapter status The computer is in sleep mode or turned off; The battery has more than 20% charge. Disconnected The battery has between 5% and Solid amber 20% charge. The battery has between 1% and 5% Fast blinking amber charge. -
Page 34: Hotkeys
Hardware Maintenance Manual Hotkeys You can access certain system settings quickly by pressing the appropriate hotkeys. Table 3. Hotkeys Enables/disables airplane Mutes/unmutes the sound. mode. Decreases the volume level. Enables/disables camera. Increases the volume level. Locks the LCD screen. Enables the external Enables/disables projector or dangles the microphone. external display. Decreases display Refreshes page. brightness. Enables/disables the touch Increases display pad. brightness. -
Page 35: Fru Replacement Notices
330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: • They maintain tight connections. • They do not easily come loose, even with shock or vibration. • They are harder to tighten. -
Page 36: Removing And Replacing An Fru
Hardware Maintenance Manual Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 31. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed. 4. Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts. 5. When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure. 6. When removing the FRU, move it in the direction as given by the arrow in the figure. 7. To put the new FRU in place, reverse the removal procedures and follow any of the notes that pertain to replacement. For information about connecting and arranging internal cables, see “Locations” on page 63. -
Page 37: 1010 Optical Drive
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST 1010 Optical drive Figure 1. Removal steps of optical drive Remove the screw 1.Then pull the optical drive out in the direction shown by arrow 2. Step Screw (quantity) Color Torque M2.5 × 7 mm, Phillips head, nylok-coated (1) Black 1.85+/-0.15 kgf/cm LOW TO UPPER Remove the screw 3, then carefully remove the optical drive bracket and bezel in the directions shown by arrows 4 and 5. -
Page 38: 1020 Base Cover
Hardware Maintenance Manual 1020 Base cover For access, remove this FRU: • “1010 Optical drive” on page 33 Figure 2. Removal steps of base cover Remove the screws 1. Step Screw (quantity) Color Torque M2.5 × 7 mm, Phillips-head, nylok-coated Black 1.85+/-0.15 kgf/cm (12) - Page 39 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 2. Removal steps of base cover (continued) Remove the base cover in the directions shown by arrows 2 and 3.
- Page 40 Hardware Maintenance Manual Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: The following labels need to be peeled off from the old base cover and put on the new base cover. For countries other than China and India: Rating label 66 × 24mm Rating label for print 43 × 24mm OS label 16 × 22.5mm Office lable 17 × 21mm Argentina label 68 × 6mm Adapter label 65 × 20mm KCC label 50 × 16mm Indonesia label 32 × 10mm TW label 70 × 10mm BIS label 22 × 30mm WL/BT label 35 × 15mm For China and India: Rating label 33 × 24mm Rating label for print 43 × 24mm OS label 16 × 22.5mm...
- Page 41 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST For the location of each label, refer to the following figures: For countries other than China and India: For China and India:...
-
Page 42: 1030 Battery Pack
Hardware Maintenance Manual 1030 Battery pack DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 Figure 3. Removal steps of battery pack Detach the battery pack connector in the direction shown by arrow 1, remove the screws 2. Step Screw (quantity) Color... - Page 43 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 3. Removal steps of battery pack (continued) Remove the battery pack in the direction shown by arrow 3.
-
Page 44: 1040 Pci Express Mini Card For Wireless Lan
• “1030 Battery pack” on page 38 Important: The preinstalled WLAN module may only be replaced with a Lenovo approved module in order to comply with FCC and IC regulations. Refer to Table 4 “Parts list—Overall” on page 66 for Lenovo part numbers for the approved modules. - Page 45 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 4. Removal steps of PCI Express Mini Card for wireless LAN (continued) Remove the card in the direction shown by arrow 3. When installing: • In models with a wireless LAN card that has two antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled MAIN, and the grey cable (2nd) (AUX) into the jack labeled AUX on the card. • In models with a wireless LAN card that has three antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into the jack labeled 3, and the white cable (2nd) (AUX) into the jack labeled 2 on the card.
-
Page 46: 1050 Dimm
Hardware Maintenance Manual 1050 DIMM For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 Figure 5. Removal steps of DIMM Insert a flat blade tool into the memory module cover, and then remove the memory module cover manually. Release the two latches on both edges of the socket at the same time in the directions shown by arrows 1, and then unplug the DIMM in the direction shown by arrow 2. -
Page 47: 1060 Hard Disk Drive
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST 1060 Hard disk drive For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 Attention: • Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. - Page 48 Hardware Maintenance Manual Figure 6. Removal steps of hard disk drive (continued) Remove the hard disk drive from the slot in the direction shown by arrow C. Detach the bracket from the hard disk drive.
-
Page 49: 1070 Speakers
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST 1070 Speakers For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 Hard disk drive” on page 43 Figure 7. Removal steps of speakers Unplug the speaker connector 1. Then remove the speakers 2. When installing: Make sure that the connector is attached firmly. -
Page 50: 1080 Fan Assembly And Heat Sink Assembly
Hardware Maintenance Manual 1080 Fan assembly and Heat Sink assembly For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 Hard disk drive” on page 43 • “1070 Speakers” on page 45 Figure 8. Removal steps of fan assembly and Heat Sink assembly Release the cables from the cable guides in the direction shown by arrows 1. When installing: Route the antenna cables along the cable guides. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. - Page 51 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 8. Removal steps of fan assembly and Heat Sink assembly (continued) Unplug the fan connector in the direction shown by arrow 2. Remove the screw 3.
- Page 52 Hardware Maintenance Manual Figure 8. Removal steps of fan assembly and Heat Sink assembly (continued) Loosen the screws 5. Lift the heat sink in the direction shown by arrow 6 .
- Page 53 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 8. Removal steps of fan assembly and Heat Sink assembly (continued) When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, to the part shown in the figure above. Either too much or too little grease application can cause a thermal...
-
Page 54: 1090 Odd Transfer Board, Backup Battery And Fingerprint Board
Hardware Maintenance Manual 1090 ODD transfer board, backup battery and fingerprint board For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 Hard disk drive” on page 43 • “1070 Speakers” on page 45 • “1080 Fan assembly and Heat Sink assembly” on page 46 Figure 9. Removal steps of ODD transfer board, backup battery and fingerprint board Detach the system board connector in the directions shown by arrows 1 and 2. - Page 55 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 9. Removal steps of ODD transfer board, backup battery and fingerprint board (continued) Remove the backup battery in the direction shown by arrow 6. When installing: Make sure that the connector is attached firmly.
-
Page 56: 1100 Upper Case
Hardware Maintenance Manual 1100 Upper case For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 Hard disk drive” on page 43 • “1070 Speakers” on page 45 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 ODD transfer board, backup battery and fingerprint board” on page Figure 10. Removal steps of upper case Remove the screws 1. - Page 57 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 10. Removal steps of upper case (continued) Detach the LCD unit connectors in the directions shown by arrows 2 and C. Open the hinge in the direction shown by arrows D.
- Page 58 Hardware Maintenance Manual Figure 10. Removal steps of upper case (continued) Remove the upper case from the LCD module in the directions shown by arrow E.
-
Page 59: 1110 System Board
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST 1110 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. - Page 60 Hardware Maintenance Manual Figure 11. Removal steps of system board (continued) Remove the system board in the direction shown by arrow 4.
-
Page 61: 1120 Lcd Unit
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST 1120 LCD unit For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 Hard disk drive” on page 43 • “1070 Speakers” on page 45 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 ODD transfer board, backup battery and fingerprint board” on page • “1100 Upper case” on page 52 • “1110 System board” on page 55... - Page 62 Hardware Maintenance Manual Figure 12. Removal steps of LCD unit (continued) Remove the LCD front bezel in the direction shown by arrows 1. Remove the screws 2. Lift the LCD module slightly in the direction shown by arrow 3. Disconnect the connector in the direction shown by arrow 4. Then remove the LCD module. Step Screw (quantity) Color Torque M2 × 3 mm, Phillips-head, nylok-coated (4) Silver 1.85+/-0.15 kgf/cm lcd panel---lcd cover...
- Page 63 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Figure 12. Removal steps of LCD unit (continued) Remove the screws 5. Step Screw (quantity) Color Torque M2.5 × 2.5 mm, Phillips-head, nylok-coated (6) Silver 3+/-0.15 kgf/cm lcd brk---lcd cover Remove the LCD hinges in the direction shown by arrows 6.
- Page 64 Hardware Maintenance Manual Figure 12. Removal steps of LCD unit (continued) Detach the camera connector in the direction shown by arrow 7. Remove the LCD cable in the direction shown by arrows 8. When installing: Make sure that the connector is attached firmly and that you do not pinch the antenna cables when you attach the LCD assembly. Route the LCD cable along the cable guides.
-
Page 65: 1130 Integrated Camera And Antenna Assembly
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST 1130 Integrated camera and antenna assembly For access, remove these FRUs in order: • “1010 Optical drive” on page 33 • “1020 Base cover” on page 34 • “1030 Battery pack” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 Hard disk drive” on page 43 • “1070 Speakers” on page 45 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 ODD transfer board, backup battery and fingerprint board” on page... - Page 66 Hardware Maintenance Manual Figure 13. Removal steps of integrated camera and antenna assembly (continued) Peel off the adhesive tape securing the antenna boards, release the cables from the cable guide, and then remove the antenna assembly in the direction shown by arrows B.
-
Page 67: Locations
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Locations Front view and right-side view 1 Integrated camera 2 Built-in microphone 3 Computer display 4 Ventilation slots 5 Touch pad 6 Numeric keypad 7 Wireless LAN antennas 8 Power Key 9 Kensington Mini Security slot... -
Page 68: Bottom And Left-Side View
Hardware Maintenance Manual Bottom and Left-side view 1 Speakers 2 Ventilation slots 3 AC power adapter jack 4 Battery/Charging status indicator 5 RJ-45 port 6 HDMI port 7 USB 3.0 port 8 USB 2.0 port (on select models) 9 Combo audio jack J Memory card slot K Novo button L Power status indicator... -
Page 69: Parts List
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Parts list This section presents the following service parts: • “Overall” on page 66 • “LCD FRUs” on page 70 • “Miscellaneous parts” on page 71 • “AC adapters” on page 72 • “Screws” on page 73 Note: Each FRU is available for all types or models, unless specific types or models are specified. -
Page 70: Overall
Hardware Maintenance Manual Overall... - Page 71 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Table 4. Parts list—Overall FRU no. See “Miscellaneous parts” on page 71. LCD unit (see “LCD FRUs” on page 70). UpCaseASM W/KB NFP L81DK PG ENG 5CB0R20167 UpCaseASM W/KB NFP L81DK PG UKE 5CB0R20162 UpCaseASM W/KB NFP L81DK PG ITA 5CB0R20169 UpCaseASM W/KB NFP L81DK PG SPA 5CB0R20195 UpCaseASM W/KB NFP L81DK PG TUR 5CB0R20175 UpCaseASM W/KB NFP L81DK PG THAI 5CB0R20220 UpCaseASM W/KB NFP L81DK PG POR 5CB0R20201 UpCaseASM W/KB NFP L81DK PG LA SPA...
- Page 72 Hardware Maintenance Manual Table 4. Parts list—Overall (continued) FRU no. UpCaseASM W/KB NFP L81DK IG ARA 5CB0R20213 UpCaseASM W/KB NFP L81DK IG BRL 5CB0R20183 UpCaseASM W/KB NFP L81DK IG JPN 5CB0R20197 UpCaseASM W/KB NFP L81DK IG GRE 5CB0R20170 UpCaseASM W/KB NFP L81DK IG HBW 5CB0R20187 UpCaseASM W/KB NFP L81DK IG HUN 5CB0R20211 UpCaseASM W/KB NFP L81DK IG NORDIC 5CB0R20159 UpCaseASM W/KB NFP L81DK IG BEL 5CB0R20174 UpCaseASM W/KB NFP L81DK IG ILD 5CB0R20203 UpCaseASM W/KB NFP L81DK IG SLV 5CB0R20218 UpCaseASM W/KB NFP L81DK IG SWS 5CB0R20216 UpCaseASM W/KBNFPL81DK IG EURO ENG 5CB0R20160 UpCaseASM W/KBNFP L81DK IG CZE/SLK 5CB0R20214 UpCaseASM W/KB NFP L81DK IG BUL 5CB0R20199 UpCaseASM W/KB NFP L81DK IG HIN 5CB0R20194 UpCaseASM W/KBNFP L81DK IG FRA/ARA 5CB0R20200 UpCaseASM W/KB NFP L81DK IG UKR...
- Page 73 Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Table 4. Parts list—Overall (continued) FRU no. LG L17L2PF1 7.56V30Wh2cell bty 5B10Q41213 CP/C L16C2PB1 7.6V35Wh2cell 5B10M88059 LOWER CASE 81D7 GRAPHITE GREY 5CB0R34352 ODD Bezel 81DA PG 5B30R13437 DUMMY ODD 81DA PG 5M20R13432 PLDS DA-8AESH 9.0 mm ODD 5DX0L08424 HLDS GUE0N DVD RW 5DX0J46488 THERMAL MODULE UMA L80XW 5H40P15350...
-
Page 74: Lcd Frus
Hardware Maintenance Manual LCD FRUs... -
Page 75: Miscellaneous Parts
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Table 5. Parts list—LCD FRUs FRU no. LCD BEZEL L80XM 5B30N91539 HINGE CAP L80XM OB 5CB0N91547 HINGE CAP L80XM PG 5CB0N91542 HINGE L+R L80XM 5H50N91546 BO NT173WDM-N21 HD+T AG F NB 5D10J46202 IN N173HCE E31 C1 FHDI AG S NB 5D10Q16070 AU B173HAN01.7 0A FHDI AG S NB 5D10Q16071 CAMERA 81DA 720P W/MIC 5C20R13441 CAMERA L80XM 0.3M W/MIC... -
Page 76: Ac Adapters
Hardware Maintenance Manual AC adapters Table 7. Parts list—AC adapters PA-1450-55LR 20V2.25A COO 01FR122 ADL45WCK 20V2.25A COO 01FR130 ADLX65CCGU2A 20V3.25A COO 01FR154 PA-1450-55LS 20V2.25A COO 01FR123 ADP-45DW J 20V2.25A COO 01FR110 PA-1450-55LK 20V2.25A COO 01FR036 ADL45WCE 20V2.25A COO 01FR131 ADLX65CDGU2A 20V3.25A COO 01FR137 ADLX65CCGC2A 20V3.25A COO 01FR152 PA-1450-55LI 20V2.25A COO 01FR121 ADLX65CLGU2A 20V3.25A COO 01FR146 ADLX65CLGR2A 20V3.25A COO 01FR148 ADP-45DW E 20V2.25A COO 01FR115 ADP-45DW G 20V2.25A COO 01FR114 ADL45WCC 20V2.25A COO 01FR128 ADLX65CCGR2A 20V3.25A COO 01FR157 ADLX65CCGK2A 20V3.25A COO... -
Page 77: Screws
Lenovo ideapad 330-17AST/ideapad 330-17AST D/ideapad 330-17AST U/ ideapad 330E-17AST D/ideapad 330E-17AST U/ideapad 330H-17AST/ ideapad 330L-17AST/ideapad 330E-17AST/ideapad 330R-17AST Table 7. Parts list—AC adapters (continued) ADP-45DW D 20V2.25A COO 01FR112 ADLX65CDGE2A 20V3.25A COO 01FR142 ADLX65CCGE2A 20V3.25A COO 01FR159 ADLX65CLGA2A 20V3.25A COO 01FR149 ADL45WCF 20V2.25A COO 01FR132 PA-1450-55LU 20V2.25A COO 01FR124 ADP-45DW K 20V2.25A COO 01FR117 PA-1450-55LG 20V2.25A COO 01FR119 ADL45WCB 20V2.25A COO... -
Page 78: Notices
Hardware Maintenance Manual Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the... -
Page 79: Trademarks
Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. Lenovo Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. Other company, products, or service names may be trademarks or service...