Table of Contents
Advertisement
Basic TV operation
Before operating your TV, make sure the following
instructions have been completed.
• Your TV has been connected to an antenna or a
cable system.
• Your TV has been plugged in a power outlet.
• In this manual, the OSD (On Screen Display)
may be different from your TV's because it is
just an example to help you with the TV
operation.
Turning on/off the TV
Press the POWER (or ON/OFF) button on the set.
At this time, the set switches to standby mode and
the standby indicator lights up in red.
To switch the TV on from standby mode, press
the TV/VIDEO, CH
/
D
E
POWER, TV/VIDEO, CH
D
on the remote control.
A channel number will be displayed on the screen.
The on-screen display will disappear after a few
seconds.
Press the POWER button on the remote control. It
reverts to standby mode.
To switch the TV off, press the POWER button on
the set.
Selecting the on screen language
1. Press the MENU button and then use the
button until the menu is displayed as shown
right.
2. Press the
G
and then use the
select
.
Language
3. Press the
and then use the
G
select the desired language.
From this point on, the on-screen display will be
presented in the language of your choice.
4. Repeatedly press the MENU button to exit.
Memorizing Channels
This is the function to memorize all the active
channels in your area before you can use the TV.
There are two ways of memorizing channels. You
can use either.One is called AUTO PROGRAM
and the other is called MANUAL PROGRAM.
In AUTO PROGRAM the TV will memorize the
channels in ascending order. If there are
additional channels you want to add or delete, you
can manually add or delete those channels.
Memorizing the Channels by
AUTO PROGRAM
AUTO PROGRAM searches and memorizes all
the active channels in your area then you can
select the desired channel with the
Using the AUTO PRG./A.PROG button
You can conveniently perform AUTO PROGRAM
AUTO PRG./A.PROG
using the
remote control.
1. Press the
2. Press the
If you want to stop auto programming, press the
ENTER (
Only the channels searched up to that time are
memorized.
Notes: •If the programmed signal has poor
quality, memorize again in the
•AUTO PROGRAM stores all receivable channels
regardless of receiving signal (RF, Cable).
•If channels of general wireless TV and cable TV
are duplicated, press the number buttons (0 ~ 9) to
change as .
button on the set or
/
or number button
E
Using the MENU button
1. Press the MENU button and then use the
2. Press the
3. Press the
/
D
E
4. The AUTO PROGRAM starts now.
Memorizing the Channels by
MANUAL PROGRAM
/
button to
D
E
Using the MEMORY/ERASE button
/
button to
D
E
You can conveniently perform MANUAL
PROGRAM using the MEMORY / ERASE button
on the remote control.
1. Press the
2. Press the MEMORY/ERASE button to select
Selecting the Channel
Press the
upper or lower channel then the channel being
viewed, or NUMBER buttons to directly select the
desired channel.
Adjusting the Volume
Press the
F
To mute the sound, Press the MUTE button.
The word
/
buttons.
D
E
It's convenient when you get the telephone calls.
To restore the muted sound, press the MUTE
button again or VOL
button on the
6
AUTO PRG./A.PROG
or
AUTO PRG./A.PROG
G
The AUTO PROGRAM starts now.
) button.
A
Auto prog.
Channels of general
wireless TV
button the until the menu is displayed as shown
right.
G
and then use the
select
Auto prog.
.
G
button to enter the
mode.
/
or NUMBER buttons to select
D
E
the channel number you want to memorize or
erase.
Memory
or
Erase
.
The on screen display appears as shown right.
/
button to conveniently select the
D
E
button to increase the volume level or
G
button to decrease the volume level.
Mute
is displayed.
/
button.
F
G
button.
button.
Channels of
Cable TV
/
D
E
/
button to
D
E
Auto prog.
Advertisement
Table of Contents
