Page 1: User Guide
™ ThinkCentre User Guide Types 2296, 8191, 8198, 8199, 8316, 8434...
Page 3 ™ ThinkCentre User Guide Types 2296, 8191, 8198, 8199, 8316, 8434...
Page 4 Note Before using this information and the product it supports, be sure to read the “Safety Information” on page v and Appendix E, “Notices”, on page 111. First Edition (June 2003) © Copyright International Business Machines Corporation 2003. All rights reserved. US Government Users Restricted Rights –...
Page 5: Table Of Contents
Contents Safety Information ..v Lithium battery notice . Modem safety information . Laser compliance statement . Overview ....ix Information resources .
Page 6 Obtaining device drivers . Removing the cover Locating components . Identifying parts on the system board Installing memory . Installing adapters . Installing internal drives . Drive specifications . Installing a drive Installing security features . Identifying security locks . Rope clip .
Page 7: Safety Information
Safety Information DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product.
Page 8: Lithium Battery Notice
réseaux, aux systèmes de té lécommunication et aux modems (sauf instruction contraire mentionnée dans les procédures d’installation et de configuration). v Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent produit ou des périphériques qui lui sont raccordés, reportez-vous aux instructions ci-dessous pour connecter et déconnecter les différents cordons.
Page 9: Laser Compliance Statement
v Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. v Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. v Use caution when installing or modifying telephone lines. v Avoid using a telephone (other than a cordless type) during an electrical storm.
Page 10 DANGER Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. DANGER: Certains modèles d’ordinateurs personnels sont équipés d’origine d’une unité de CD-ROM ou de DVD-ROM. Mais ces unités sont également vendues séparément en tant qu’options.
Page 11: Overview
It also includes basic troubleshooting information, software recovery procedures, help and service information, and warranty information. Access IBM, on your desktop, provides a link to more information about your computer. If you have Internet access, the most up-to-date manuals for your computer are available from the World Wide Web.
Page 12: Identifying Your Computer
Identifying your computer User Guide See Chapter 1, “Type 8316”, on page 1. See Chapter 2, “Type 8191”, on page 23. See Chapter 3, “Types 2296 and 8434”, on page 45. See Chapter 4, “Types 8198 and 8199”, on page 69.
Page 13: Chapter 1. Type 8316
Chapter 1. Type 8316 This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option.
Page 14 Video subsystem v Intel Extreme v Accelerated graphics port (AGP) video adapter slot on the system board (some models) Audio subsystem Integrated SoundMAX 3 audio Connectivity v 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on ® feature v Soft modem V.90/V.44 (some models) System management features v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)
Page 15 Security features v User and administrator passwords v Support for the addition of a rope clip and lockable cable v Support for the addition of an integrated cable lock v Startup sequence control v Startup without diskette drive, keyboard, or mouse v Unattended start mode v Diskette and hard disk I/O control v Serial and parallel port I/O control...
Page 16: Specifications
Specifications This section lists the physical specifications for your computer. Dimensions Height: 104 mm (4.1 in.) Width: 360 mm (14.2 in.) Depth: 412 mm (16.2 in.) Weight Minimum configuration as shipped: 8.1 kg (18 lb) Maximum configuration: 9.1 kg (20 lb) Environment Air temperature: System on: 10°...
Page 17: Available Options
Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...
Page 18: Installing External Options
v Always handle components carefully. Handle adapters and memory modules by the edges. Never touch any exposed circuitry. v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds.
Page 19: Locating The Connectors On The Rear Of Your Computer
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. 1 Serial connector 2 Mouse connector 3 Parallel connector 4 Ethernet connector 5 Audio line in connector 6 Power connector 7 PCI slots 8 AGP slot (some models)
Page 20: Obtaining Device Drivers
Connector Serial connector Mouse connector Parallel connector Ethernet connector Audio line in connector Audio line out connector Microphone connector USB connectors Keyboard connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.ibm.com/pc/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files.
Page 21: Removing The Cover
Removing the cover Important Read “Safety Information” on page v and “Handling static-sensitive devices” on page 5 before removing the cover. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2.
Page 22: Locating Components
Locating components The following illustration will help you locate the various components in your computer. 1 Power supply 2 PCI slot 3 AGP slot 4 Support bar Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer.
Page 23: Installing Memory
The following illustration shows the locations of parts on the system board. 1 Microprocessor 2 DIMM connector 1 3 DIMM connector 2 4 Power connector 5 Diskette drive connector 6 Primary IDE connector 7 Front panel connector 8 Secondary IDE connector 9 Battery Installing memory Your computer has two connectors for installing dual inline memory modules...
Page 24: Installing Adapters
2. To locate the DIMM connectors. See “Identifying parts on the system board” on page 10. 3. Open the retaining clips. 4. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close.
Page 25 2. Pivot one of the drive bay latch handles toward the front of the computer and then pivot the drive bay cage upward, as shown, until it is latched in the up position. Repeat this procedure for the remaining drive bay. 3.
Page 26: Installing Internal Drives
7. Install the adapter-slot-cover latch. 8. Clear any cables that might impede the replacement of the drive bays. 9. Replace the support bar and pivot the two drive bays back to their original positions. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables”...
Page 27: Installing A Cd-Rom Or Dvd-Rom Drive
The following illustration shows the locations of the drive bays. The following list describes some of the drives that you can install in each bay and their height requirements: 1 Bay 1 - Maximum height: 25.8 mm (1.0 in.) 3.5-inch diskette drive (preinstalled) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) CD-ROM drive or DVD-ROM drive 3 Bay 3 - Maximum height: 25.8 mm (1.0 in.) 3.5-inch hard disk drive (preinstalled) Notes:...
Page 28 6. Install the drive into the bay. Align the screw holes and insert the two screws. 7. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply, and a signal cable that connects to the system board.
Page 29: Installing Security Features
Installing security features To help prevent hardware theft and unauthorized access to your computer, several security lock options are available. The following sections will help you identify and install the various types of locks that might be available for your computer. In addition to physical locks, unauthorized use of your computer can be prevented by a software lock that locks the keyboard until a correct password is typed in.
Page 30 5. Replace the computer cover. For more information, see “Replacing the cover and connecting the cables” on page 21. 6. Thread the cable through the rope clip and around an object that is not a part of or permanently secured to the building structure or foundation, and from which it cannot be removed;...
Page 31: Integrated Cable Lock
Integrated cable lock With an integrated cable lock (sometimes referred to as a Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to a security slot at the rear of your computer and is operated with a key.
Page 32: Erasing A Lost Or Forgotten Password (Clearing Cmos)
Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwords. For more information about lost or forgotten passwords, see Access IBM on your desktop. Note: Some models have a POV daughter card installed on the system board. In these models, the password is stored in the EEPROM on the POV card and cannot be erased.
Page 33: Replacing The Cover And Connecting The Cables
3. Locate the Clear CMOS/Recovery jumper on the system board. See “Identifying parts on the system board” on page 10. 4. If necessary, see “Installing adapters” on page 12 to remove any adapters that impede access to the Clear CMOS/Recovery jumper. 5.
Page 34 User Guide...
Page 35: Chapter 2. Type 8191
Chapter 2. Type 8191 This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option.
Page 36 Video subsystem v Intel Extreme v Accelerated graphics port (AGP) video adapter slot on the system board (some models) Audio subsystem Integrated SoundMAX 3 audio Connectivity 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN feature System management features v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port...
Page 37 v Startup without diskette drive, keyboard, or mouse v Unattended start mode v Diskette and hard disk I/O control v Serial and parallel port I/O control v Security profile by device IBM preinstalled software Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included.
Page 38: Specifications
Specifications This section lists the physical specifications for your computer. Dimensions Height: 140 mm (5.5 in.) Width: 425 mm (16.7 in.) Depth: 425 mm (16.7 in) Weight Minimum configuration as shipped: 10.0 kg (22 lb) Maximum configuration: 11.4 kg (25.0 lb) Environment Air temperature: System on: 10°...
Page 39: Available Options
Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...
Page 40: Installing External Options
v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body.
Page 41: Locating The Connectors On The Rear Of Your Computer
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. 1 Power connector 2 Serial connector 3 Mouse connector 4 Parallel connector 5 Ethernet connector 6 Audio line in connector 7 PCI slots 8 AGP slot (some models) Note: Some connectors on the rear of the computer are color-coded to help you to...
Page 42: Obtaining Device Drivers
Connector Serial connector Mouse connector Parallel connector Ethernet connector Audio line in connector Audio line out connector Microphone connector USB connectors Keyboard connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.ibm.com/pc/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files.
Page 43: Removing The Cover
Removing the cover Important: Read “Safety Information” on page v and “Handling static-sensitive devices” on page 27 before removing the cover. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2.
Page 44: Locating Components
Locating components The following illustration will help you locate the various components in your computer. 1 CD drive or DVD drive 2 USB connector 3 USB connector 4 Optional drive bay 5 Hard disk drive 6 Diskette drive Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer.
Page 45: Installing Memory
The following illustration shows the locations of parts on the system board. 1 Microprocessor 2 DIMM connector 1 3 DIMM connector 2 4 Power connector 5 Diskette drive connector 6 Primary IDE connector 7 Front panel connector 8 Secondary IDE connector 9 Battery Installing memory Your computer has two connectors for installing dual inline memory modules...
Page 46: Installing Adapters
2. You might have to remove an adapter to gain access to the DIMM slots. See “Installing adapters” on page 34. 3. To locate the DIMM connectors. See “Identifying parts on the system board” on page 32. 4. Open the retaining clips. 5.
Page 47 2. Remove the adapter-slot-cover latch and the slot cover for the appropriate expansion slot. 3. Remove the adapter from its static-protective package. 4. Install the adapter into the appropriate slot on the system board. 5. Install the adapter-slot-cover latch. What to do next: v To work with another option, go to the appropriate section.
Page 48: Installing Internal Drives
Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media.
Page 49: Installing A Drive
The following illustration shows the locations of the drive bays. The following list describes some of the drives that you can install in each bay and their height requirements: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3 Bay 3 - Maximum height: 25.8 mm (1.0 in.) 4 Bay 4 - Maximum height: 25.8 mm (1.0 in.) Notes:...
Page 50 4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Pivot the drive-bay latch handle toward the front of the computer and then pivot the drive-bay cage upward, as shown, until it is latched in the upright position.
Page 51 7. Install the drive into the bay. Align the screw holes and insert the two screws. 8. Pivot the drive-bay cage back into place. 9. A hard disk drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board.
Page 52: Installing Security Features
Connecting an additional CD drive, DVD drive, or hard disk drive 1. Locate the secondary IDE connector on the system board and the three-connector signal cable. See “Identifying parts on the system board” on page 32. 2. Connect the extra connector in the signal cable to the new drive. 3.
Page 53 3. Insert the rope clip through the rear panel; then attach and tighten the nuts with an appropriately sized or adjustable wrench. 4. Replace the computer cover. For more information, see “Replacing the cover and connecting the cables” on page 44. 5.
Page 54: Integrated Cable Lock
Integrated cable lock With an integrated cable lock (sometimes referred to as a Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to a security slot at the rear of your computer and is operated with a key.
Page 55: Erasing A Lost Or Forgotten Password (Clearing Cmos)
Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwords. For more information about lost or forgotten passwords, see Access IBM on your desktop. Note: Some models have a POV daughter card installed on the system board. In these models, the password is stored in the EEPROM on the POV card and cannot be erased.
Page 56: Replacing The Cover And Connecting The Cables
3. Locate the Clear CMOS/Recovery jumper on the system board. See “Identifying parts on the system board” on page 32. 4. If necessary, see “Installing adapters” on page 34 to remove any adapters that impede access to the Clear CMOS/Recovery jumper. 5.
Page 57: Copyright Ibm Corp
Chapter 3. Types 2296 and 8434 This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option.
Page 58 v Internal hard disk drive v EIDE CD-ROM or DVD-ROM drive (some models) Video subsystem v Dynamic video memory technology v Accelerated graphics port (AGP) video adapter slot on the system board (some models) Audio subsystem Integrated SoundMax 3 audio subsystem Connectivity v 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on ®...
Page 59 Security features v User and administrator passwords v Support for the addition of a rope clip and lockable cable v Support for the addition of an integrated cable lock (see Access IBM) v Support for a padlock on the chassis v Startup sequence control v Startup without diskette drive, keyboard, or mouse v Unattended start mode...
Page 60: Specifications
Specifications This section lists the physical specifications for your computer. Dimensions Height: 398 mm (15.67 in.) Width: 180 mm (7.08 in.) Depth: 402 mm (15.82 in.) Weight Minimum configuration as shipped: 7.6 kg (16.8 lb) Maximum configuration: 9.97 kg (22 lb) Environment Air temperature: System on: 10°...
Page 61: Available Options
Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...
Page 62: Installing External Options
v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body.
Page 63: Locating The Connectors On The Front Of Your Computer
Locating the connectors on the front of your computer The following illustration shows the locations of the USB connectors on the front of the computer. 1 USB connector 2 USB connector Chapter 3. Types 2296 and 8434...
Page 64: Locating The Connectors On The Rear Of Your Computer
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the back of the computer. Power connector Mouse connector Keyboard connector USB connectors Serial connector Parallel connector Monitor connector USB connectors Note: Some connectors on the rear of the computer are color-coded to help you to determine where to connect the cables on your computer.
Page 65: Obtaining Device Drivers
Connector Mouse connector Keyboard connector USB connectors Serial connector Parallel connector Ethernet connector Microphone connector Audio line out connector Audio line in connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.ibm.com/pc/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files.
Page 66: Removing The Cover
Removing the cover Important Read “Safety Information” on page v and “Handling static-sensitive devices” on page 49 before removing the cover. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2.
Page 67: Locating Components
Locating components The following illustration will help you locate the various components in your computer. 1 Microprocessor and heat sink 2 DIMMs 3 AGP slot (some models) Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer.
Page 68: Installing Memory
The following illustration shows the locations of parts on the system board. 1 Microprocessor 2 DIMM connector 1 3 DIMM connector 2 4 Power connector 5 Diskette drive connector 6 Primary IDE connector 7 Front panel connector 8 Secondary IDE connector 9 Battery Installing memory Your computer has two connectors for installing dual inline memory modules...
Page 69 2. You might have to remove an adapter to gain access to the DIMM slots. See “Installing adapters” on page 58. 3. Locate the DIMM connectors. See “Identifying parts on the system board” on page 55. 4. Open the retaining clips. 5.
Page 70: Installing Adapters
Installing adapters This section provides information and instructions for installing and removing adapters. Your computer has three expansion slots for PCI adapters. One slot, used for an AGP adapter, is available on some models. You can install an adapter up to 228 mm (9 inches) long.
Page 71: Installing Internal Drives
5. Secure the adapter with the screw as shown. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 67. Installing internal drives This section provides information and instructions for installing and removing internal drives.
Page 72: Installing A Drive
v A 3.5-inch diskette disk drive in bay 3 v A 3.5-inch hard drive in bay 4 Any bay that does not have a drive installed has a static shield and bay panel installed. The following illustration shows the locations of the drive bays. The following table describes some of the drives you can install in each bay and their height requirements.
Page 73 4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Make sure the drive that you are installing is set correctly as either a master or a slave device.
Page 74: Installing Security Features
7. A hard disk drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board. The steps to connect a drive are different depending on the type of drive you are connecting.
Page 75: Identifying Security Locks
Identifying security locks The following illustration shows the locations of the security features on the rear of the computer. 1 Rope clip 2 Integrated cable lock 3 Padlock loop Rope clip Using a 3/16-inch or 5-mm rope clip (sometimes referred to as a U-bolt), a steel security cable, and a padlock can secure your computer to a desk, table, or other non-permanent fixture.
Page 76 5. Thread the cable through the rope clip and around an object that is not a part of or permanently secured to the building structure or foundation, and from which it cannot be removed; then fasten the cable ends together with a lock. User Guide...
Page 77: Integrated Cable Lock
Integrated cable lock With an integrated cable lock (sometimes referred to as a Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to a security slot at the rear of your computer and is operated with a key.
Page 78: Erasing A Lost Or Forgotten Password (Clearing Cmos)
Refer to “Lithium battery notice” on page vi for information about replacing and disposing of the battery. To change the battery: 1. Turn off the computer and all attached devices. 2. Unplug the power cord and remove the cover. See “Removing the cover” on page 54.
Page 79: Replacing The Cover And Connecting The Cables
3. Locate the Clear CMOS/Recovery jumper on the system board. See “Identifying parts on the system board” on page 55. 4. If necessary, see “Installing adapters” on page 58 to remove any adapters that impede access to the Clear CMOS/Recovery jumper. 5.
Page 80 the screws that secure the cover. 4. Reconnect the external cables and power cords to the computer. See “Installing external options” on page 50. 5. To update the configuration, see Chapter 5, “Using the IBM Setup Utility program”, on page 93. Important: When the power cord is first plugged in, the computer might appear to turn on for a few seconds and then turn off.
Page 81: Chapter 4. Types 8198 And 8199
Chapter 4. Types 8198 and 8199 This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option.
Page 82 Internal drives v 3.5-inch, 1.44 MB diskette drive v Internal hard disk drive v EIDE CD-ROM or DVD-ROM drive (some models) Video subsystem v Dynamic video memory technology v Accelerated graphics port (AGP) video adapter slot on the system board (some models) Audio subsystem Integrated SoundMax 3 audio subsystem...
Page 83 Power v 230 W power supply with manual voltage selection switch v Automatic 50/60 Hz input frequency switching v Advanced Power Management support v Advanced Configuration and Power Interface (ACPI) support Security features v User and administrator passwords v Support for the addition of a rope clip and lockable cable v Support for the addition of an integrated cable lock v Support for a padlock on the chassis v Startup sequence control...
Page 84: Specifications
Specifications This section lists the physical specifications for your computer. Dimensions Height: 413 mm (16.25 in.) Width: 191 mm (7.5 in.) Depth: 406 mm (16 in.) Weight Minimum configuration as shipped: 9.1 kg (20 lb) Maximum configuration: 11.4 kg (25.0 lb) Environment Air temperature: System on: 10°...
Page 85: Available Options
Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...
Page 86: Installing External Options
v Always handle components carefully. Handle adapters and memory modules by the edges. Never touch any exposed circuitry. v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds.
Page 87: Locating The Connectors On The Front Of Your Computer
Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer. Note: Not all computer models will have the following connectors. 1 IEEE 1394 connector 2 Microphone connector 3 Headphone connector 4 USB connector 5 USB connector...
Page 88: Locating The Connectors On The Rear Of Your Computer
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the back of the computer. 1 Power connector 2 Serial connector 3 Mouse connector 4 Keyboard connector 5 USB connectors 6 Serial connector 7 Parallel connector 8 VGA monitor connector Note: Some connectors on the rear of the computer are color-coded to help you to...
Page 89: Obtaining Device Drivers
Connector Serial connector Mouse connector Keyboard connector USB connectors Parallel connector Ethernet connector Microphone connector Audio line out connector Audio line in connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.ibm.com/pc/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files.
Page 90: Removing The Cover
Removing the cover Important Read “Safety Information” on page v and “Handling static-sensitive devices” on page 73 before removing the cover. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2.
Page 91: Locating Components
Locating components The following illustration will help you locate the various components in your computer. 1 Microprocessor and heat sink 2 DIMMs 3 AGP slot Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer.
Page 92: Installing Memory
The following illustration shows the locations of parts on the system board. 1 Microprocessor 2 DIMM connector 1 3 DIMM connector 2 4 Power connector 5 Diskette drive connector 6 Primary IDE connector 7 Front panel connector 8 Secondary IDE connector 9 Battery Installing memory Your computer has two connectors for installing dual inline memory modules...
Page 93: Installing Adapters
2. You might have to remove an adapter to gain access to the DIMM slots. See “Installing adapters”. 3. Locate the DIMM connectors. See “Identifying parts on the system board” on page 79. 4. Open the retaining clips. 5. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close.
Page 94 2. Remove the adapter-slot-cover latch and the slot cover for the appropriate expansion slot. 3. Remove the adapter from its static-protective package. 4. Install the adapter into the appropriate slot on the system board. 5. Install the adapter-slot-cover latch. What to do next v To work with another option, go to the appropriate section.
Page 95: Installing Internal Drives
Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media.
Page 96 The following illustration shows the locations of the drive bays. The following list describes some of the drives you can install in each bay and their height requirements: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3 Bay 3 - Maximum height: 25.8 mm (1.0 in.) 4 Bay 4 - Maximum height: 25.8 mm (1.0 in.) 5 Bay 5 - Maximum height: 25.8 mm (1.0 in.)
Page 97 4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Make sure the drive that you are installing is set correctly as either a master or a slave device.
Page 98 6. Install the drive into the bay and lock it into position. Note: Some drives might require screws to secure the drive into the bay. If this 7. A hard disk drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board.
Page 99 Connecting an additional CD drive, DVD drive, or hard disk drive An additional drive can be connected to either the primary IDE or secondary IDE connector. 1. Locate an available IDE connector on the three-connector signal cable attached to either the primary IDE or secondary IDE connector on the system board. See “Identifying parts on the system board”...
Page 100: Rope Clip
Rope clip Using a 3/16-inch or 5-mm rope clip (sometimes referred to as a U-bolt), a steel security cable, and a padlock can secure your computer to a desk, table, or other non-permanent fixture. For computers designed to accommodate the rope clip, knockouts at the rear of the chassis are provided.
Page 101 Integrated cable lock With an integrated cable lock (sometimes referred to as a Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to a security slot at the rear of your computer and is operated with a key.
Page 102: Erasing A Lost Or Forgotten Password (Clearing Cmos)
Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwords. For more information about lost or forgotten passwords, see Access IBM on your desktop. Note: Some models have a POV daughter card installed on the system board. In these models, the password is stored in the EEPROM on the POV card and cannot be erased.
Page 103: Replacing The Cover And Connecting The Cables
To erase a forgotten password: 1. Turn off the computer and all attached devices. 2. Remove the cover. See “Removing the cover” on page 78. 3. Locate the Clear CMOS/Recovery jumper on the system board. See “Identifying parts on the system board” on page 79. 4.
Page 104 3. Position the cover on the chassis so that the rail guides on the bottom of the cover engage the rails and push the cover closed until it latches. 4. Reconnect the external cables and power cords to the computer. See “Installing external options”...
Page 105: Chapter 5. Using The Ibm Setup Utility Program
Chapter 5. Using the IBM Setup Utility program The IBM Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of your computer. The IBM Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using.
Page 106: User Password
User password The user password feature deters unauthorized persons from gaining access to your computer. Administrator password Setting an administrator password deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set an administrator password. After you set an administrator password, a password prompt is displayed each time you try to access the IBM Setup Utility program.
Page 107: Selecting A Startup Device
Selecting a startup device If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device. Selecting a temporary startup device Use this procedure to startup from any boot device.
Page 108 User Guide...
Page 109: Appendix A. Updating System Programs
Appendix A. Updating system programs This appendix contains information about updating system programs and how to recover from a POST/BIOS update failure. System programs System programs are the basic layer of software that is built into your computer. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the IBM Setup Utility program.
Page 110: Recovering From A Post/Bios Update Failure
8. From your browser, Click Back to return to the list of files. Carefully follow the printed instructions to download, extract, and install the update. Recovering from a POST/BIOS update failure If power to your computer is interrupted while POST/BIOS is being updated (flash update), your computer might not restart correctly.
Page 111: Appendix B. Cleaning The Mouse
Appendix B. Cleaning the mouse This appendix provides instructions on how to clean your mouse. The procedure will be different depending on which type of mouse you have. Cleaning an optical mouse If you experience some problems with your optical mouse, check the following: 1.
Page 112 3. Place your hand over the retainer ring and ball 2 , and then turn the mouse over, top side up, so that the retainer ring and ball fall out into your hand. 4. Wash the ball in warm, soapy water then dry it with a clean cloth. Blow air carefully into the ball cage 4 to dislodge dust and lint.
Page 113: Appendix C. Manual Modem Commands
Appendix C. Manual modem commands The following section lists commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection.
Page 114 Command Sr=n User Guide Function Force modem off-hook (make busy) Note: H1 command is not supported for Italy Display product-identification code Factory ROM checksum test Internal memory test Firmware ID Reserved ID Low speaker volume Low speaker volume Medium speaker volume High speaker volume Internal speaker off Internal speaker on until carrier detected...
Page 115: Extended At Commands
Extended AT commands Command &C_ &D_ &F_ &G_ &K_ &M_ &P_ &R_ &S_ &T_ &V Function &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command...
Page 116: Mnp/V.42/V.42Bis/V.44 Commands
Command &W_ +MS? +MS=? +MS=a,b,c,e,f MNP/V.42/V.42bis/V.44 commands Command &Q_ +DS44=0, 0 +DS44=3, 0 +DS44? +DS44=? User Guide Function &V1 Display Last Connection Statistics &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 Disable auto-retrain Enable auto-retrain Displays the current Select Modulation settings...
Page 117: Fax Class 1 Commands
Fax Class 1 commands +FAE=n +FCLASS=n +FRH=n +FRM=n +FRS=n +FTH=n +FTM=n +FTS=n Fax Class 2 commands +FCLASS=n +FAA=n +FAXERR +FBOR +FBUF? +FCFR +FCLASS= +FCON +FCIG +FCIG: +FCR +FCR= +FCSI: +FDCC= +FDCS: +FDCS= +FDIS: +FDIS= +FDR +FDT= +FDTC: +FET: +FET=N +FHNG +FLID= +FLPL +FMDL?
Page 118: Voice Commands
+FPHCTO +FPOLL +FPTS: +FPTS= +FREV? +FSPT +FTSI: Voice commands #BDR #CID #CLS #MDL? #MFR? #REV? #VBQ? #VBS #VBT #VCI? #VLS #VRA #VRN #VRX #VSDB #VSK #VSP #VSR #VSS #VTD #VTM #VTS #VTX User Guide Phase C time out. Indicates polling request. Page transfer status.
Page 119 Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix C.
Page 120 User Guide...
Page 121: Appendix D. Customer Replaceable Unit (Cru) Parts List
Appendix D. Customer replaceable unit (CRU) parts list For your computer, the following parts are designated customer replaceable unit (CRU) parts. Refer to the warranty section of your Quick Reference for more information. CRU parts list Air duct with/without fan All bezels All cables All external speakers...
Page 122 User Guide...
Page 123: Appendix E. Notices
Appendix E. Notices IBM may not offer the products, services, or features discussed in this document in all countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.
Page 124: Television Output Notice
Television output notice The following notice applies to models that have the factory-installed television-output feature. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Page 125: Index
Index adapters accelerated graphics port (AGP) 5, 27, 49, 73 installing Type 8191 34 Type 8316 12 Types 2296 and 8434 58 Types 8198 and 8199 81 peripheral component interconnect (PCI) 5, 27, 49, 73 slots 12, 34, 58, 81 audio line in connector 8, 30, 53, 77 audio line out connector 8, 30, 53, 77 audio, subsystem 2, 24, 46, 70...
Page 126 memory dual inline memory modules (DIMMs) 11, 33, 56, 80 installing 11, 33, 56, 80 system 11, 33, 56, 80 microphone connector 8, 30, 53, 77 modem Basic AT commands 101 Extended AT commands 103 Fax Class 1 commands 105 Fax Class 2 commands 105 MNP/V.42/V.42bis/V.44 commands 104 Voice commands 106...
Page 128 Part Number: 74P2399 Printed in U.S.A. (1P) P/N: 74P2399...

This manual is also suitable for:

Thinkcentre a30 8191 Thinkcentre a30 8199 Thinkcentre 2296 Thinkcentre 8191 Thinkcentre 8198 Thinkcentre 8199 ... Show all

IBM ThinkCentre A30 8198 User Manual

Safety Information

Overview

Chapter 1. Type 8316

Chapter 2. Type 8191

Chapter 3. Types 2296 and 8434

Chapter 4. Types 8198 and 8199

Chapter 5. Using the IBM Setup Utility Program

Appendix A. Updating System Programs

Appendix B. Cleaning the Mouse

Appendix C. Manual Modem Commands

Appendix D. Customer Replaceable Unit (CRU) Parts List

Appendix E. Notices

Quick Links

User Guide

Related Manuals for IBM ThinkCentre A30 8198

Summary of Contents for IBM ThinkCentre A30 8198

This manual is also suitable for:

Table of Contents