Creating Named Mac Extended Acls - Cisco 3845 - Security Bundle Router Software Manual
Software configuration guide
Hide thumbs
Also See for 3845 - Security Bundle Router:
- Manual (94 pages) ,
- Quick start manual (38 pages) ,
- Hardware installation manual (418 pages)
Table of Contents
Advertisement
Chapter 26
Configuring Network Security with ACLs
Creating Named MAC Extended ACLs
Log Buffer (4096 bytes):
00:00:48: NTP: authentication delay calculation problems
<output truncated>
00:09:34:%SEC-6-IPACCESSLOGS:list stan1 permitted 0.0.0.0 1 packet
00:09:59:%SEC-6-IPACCESSLOGS:list stan1 denied 10.1.1.15 1 packet
00:10:11:%SEC-6-IPACCESSLOGS:list stan1 permitted 0.0.0.0 1 packet
This example is a named extended access list ext1 that permits ICMP packets from any source to 10.1.1.0
0.0.0.255 and denies all UDP packets.
Switch(config)# ip access-list extended ext1
Switch(config-ext-nacl)# permit icmp any 10.1.1.0 0.0.0.255 log
Switch(config-ext-nacl)# deny udp any any log
Switch(config-std-nacl)# exit
Switch(config)# interface gigabitethernet0/2
Switch(config-if)# ip access-group ext1 in
This is a an example of a log for an extended ACL:
01:24:23:%SEC-6-IPACCESSLOGDP:list ext1 permitted icmp 10.1.1.15 -> 10.1.1.61 (0/0), 1
packet
01:25:14:%SEC-6-IPACCESSLOGDP:list ext1 permitted icmp 10.1.1.15 -> 10.1.1.61 (0/0), 7
packets
01:26:12:%SEC-6-IPACCESSLOGP:list ext1 denied udp 0.0.0.0(0) -> 255.255.255.255(0), 1
packet
01:31:33:%SEC-6-IPACCESSLOGP:list ext1 denied udp 0.0.0.0(0) -> 255.255.255.255(0), 8
packets
Note that all logging entries for IP ACLs start with
with minor variations in format
%SEC-6-IPACCESSLOG
depending on the kind of ACL and the access entry that has been matched.
This is an example of an output message when the log-input keyword is entered:
00:04:21:%SEC-6-IPACCESSLOGDP:list inputlog permitted icmp 10.1.1.10 (Vlan1
0001.42ef.a400) -> 10.1.1.61 (0/0), 1 packet
A log message for the same sort of packet using the log keyword does not include the input interface
information:
00:05:47:%SEC-6-IPACCESSLOGDP:list inputlog permitted icmp 10.1.1.10 -> 10.1.1.61 (0/0), 1
packet
Creating Named MAC Extended ACLs
You can filter non-IPv4 traffic on a VLAN or on a Layer 2 interface by using MAC addresses and named
MAC extended ACLs. The procedure is similar to that of configuring other extended named ACLs.
Note
You cannot apply named MAC extended ACLs to Layer 3 interfaces or to Layer 2 interfaces configured
with service instances.
For more information about the supported non-IP protocols in the mac access-list extended command,
see the command reference for this release.
Cisco ME 3800X and 3600X Switch Software Configuration Guide
26-26
OL-23400-01
- Quick Links:
- Performance Features
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
