X'over Setting - Kenwood KDC-X997 Instructions Manual
Hide thumbs
Also See for KDC-X997:
- Quick start manual (48 pages) ,
- Quick start manual (22 pages) ,
- Manual (151 pages)
Table of Contents
Advertisement
KDC-X997/KDC-BT955HD/KDC-X897/KDC-BT855U/KDC-X697/KDC-655U/KMR-555U
5-5. X'Over setting
5-5. X'Over setting
Fine adjusting the following setting values corresponding to the X'Over values set in the section
er
setting>.
1. Press [SRC] and select a source other than Standby ("STANDBY") using [Control] knob.
Refer to
<Source
2. Press [Control] knob.
Enters the Function setting mode.
3. Select "Audio Control"
For how to use [Control] knob, refer to
4. Select a speaker type using [Control] knob.
Speaker type
"Front"
"Rear"
"SubWoofer"
"Tweeter"[2]
(Colored
text: Factory setting)
[1]
Displayed only when "FC" is set to a value other than "Through".
[2]
Function of KDC-X997.
5. Select a setting item using [Control] knob.
6. Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [1/6].
selection>.
>
"Pro Setup"
Setting item
Setting value
Front high pass filter
KDC-X997
"FC"
Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 Hz
KDC-BT955HD
Through, 40, 60, 70, 80, 100, 120, 150, 180, 220 Hz
Front high pass slope
"SLOPE"[1][2]
-6, -12, -18, -24 dB/Oct
Front gain
"GAIN"
-8 ,-7, -6, -5, -4, -3, -2, -1,
Rear high pass filter
KDC-X997
"FC"
Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 Hz
KDC-BT955HD
Through, 40, 60, 70, 80, 100, 120, 150, 180, 220 Hz
Rear high pass slope
"SLOPE"[1][2]
-6, -12, -18, -24 dB/Oct
Rear Gain
"GAIN"
-8, -7, -6, -5, -4, -3, -2, -1,
Subwoofer low pass filter
KDC-X997
"FC"
30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250,
KDC-BT955HD
40, 60, 70, 80, 100, 120, 150, 180, 220,
Subwoofer slope
"SLOPE"[1][2]
-6, -12, -18, -24 dB/Oct
Subwoofer gain
"GAIN"
-8 ,-7, -6, -5, -4, -3, -2, -1,
Subwoofer phase
"PHASE"
"REV" (180°)/ "NML" (0°)
Shelving filter
"FC"
1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 kHz
Tweete volume
"Volume"
-8 ,-7, -6, -5, -4, -3, -2, -1,
>
"X'Over" using [Control] knob.
<3-3. How to select the
0
dB
0
dB
0
dB
0
dB
5. DSP settings (KDC-X997, KDC-BT955HD)
item>.
Through
Through
Hz
<5-4. Speak
Hz
- Quick Links:
- To Reset
- Specifications
Hide quick links:
Advertisement
Table of Contents
