Configuring The Router - Cisco ASR 1002 Quick Start Manual
Asr 1002 router
Hide thumbs
Also See for ASR 1002:
- Hardware installation manual (57 pages) ,
- Software configuration manual (378 pages) ,
- Replacing (120 pages)
Table of Contents
Advertisement
*Feb 13 13:01:28.701: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down
*Feb 13 13:01:29.728: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to
down
*Feb 13 13:01:14.738: %CPPHA-7-SYSREADY: F0: cpp_ha:
*Feb 13 13:01:14.895: %IOSXE-6-PLATFORM: F0: cpp_cp:
successful
*Feb 13 13:01:15.016: %CPPHA-7-START: F0: cpp_ha:
*Feb 13 13:01:15.756: %CPPHA-7-START: F0: cpp_ha:
*Feb 13 13:01:25.217: %CPPHA-7-START: F0: cpp_ha:
*Feb 13 13:01:25.473: %CPPHA-7-READY: F0: cpp_ha:
*Feb 13 13:01:25.473: %CPPHA-6-SYSINIT: F0: cpp_ha:
*Feb 13 13:01:26.752: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER
*Feb 13 13:01:26.913: %CPPHA-6-SYSINIT: F0: cpp_ha:
*Feb 13 13:01:26.920: %CPPHA-6-SYSINIT: F0: cpp_ha:
*Feb 13 13:01:33.990: %SYS-5-CONFIG_I: Configured from memory by console
*Feb 13 13:01:33.999: %ASR1000_OIR-2-REMSPA: SPA removed from subslot 0/1, interfaces disabled
*Feb 13 13:01:33.999: %ASR1000_OIR-2-REMSPA: SPA removed from subslot 0/2, interfaces disabled
*Feb 13 13:01:34.002: %ASR1000_OIR-2-INSCARD: Card (fp) inserted in slot F0
*Feb 13 13:01:34.002: %ASR1000_OIR-2-ONLINECARD: Card (fp) online in slot F0
*Feb 13 13:01:34.029: %ASR1000_OIR-2-INSCARD: Card (cc) inserted in slot 0
*Feb 13 13:01:34.029: %ASR1000_OIR-2-ONLINECARD: Card (cc) online in slot 0
*Feb 13 13:01:34.030: %ASR1000_OIR-2-INSSPA: SPA inserted in subslot 0/1
*Feb 13 13:01:34.034: %ASR1000_OIR-2-INSSPA: SPA inserted in subslot 0/2
*Feb 13 13:01:34.370: %SYS-5-RESTART: System restarted --
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVIPSERVICESK9-M), Experimental Version
12.2(20080114:101630) [BLD-v122_33_xn_asr_rls0_throttle.MCP_CRYPTO_THROTTLE_BLD_20080114 102]
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Mon 14-Jan-08 02:19 by mcpre
*Feb 13 13:01:36.253: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded from the Shell
Manager
*Feb 13 13:01:36.326: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
Router>
You have the option of proceeding with the setup command facility to configure the interfaces or exiting from setup
Note
and using configuration commands to configure global (system-wide) and interface-specific parameters. You do not
have to configure the interfaces immediately; however, you cannot enable the interfaces or connect them to any
networks until you have configured them. For detailed software configuration information, see the Cisco ASR 1000
series Aggregation Services Routers Software Configuration Guide.
6
Configuring the Router
Use this section for information on configuring the Cisco ASR 1002 Router.
Using the Console to Access the CLI
To access the command-line interface using the console, follow these steps:
Your system is booting and if you answer No, at the prompt:
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Press Return to enter user EXEC mode. The following prompt appears:
Step 1
Router>
From user EXEC configuration mode, enter the enable command as shown in the following example:
Step 2
22
CPP client process FMAN-FP (5 of 5) ready.
cpp_mlp_svr_client_bind: cpp_mlp_svr_ifm_init()
CPP 0 preparing image /usr/cpp/bin/cpp-mcplo-ucode
CPP 0 startup init image /usr/cpp/bin/cpp-mcplo-ucode
CPP 0 running init image /usr/cpp/bin/cpp-mcplo-ucode
CPP 0 loading and initialization complete
CPP HA system configuration start.
CPP HA system enabled.
CPP HA system initializaton complete.
Advertisement
Table of Contents
