Rsp720 With 10Ge Uplink Ports; Rsp720-10Ge Features - Cisco 7600 Series Manual
Router supervisor engine and route switch
Hide thumbs
Also See for 7600 Series:
- Hardware installation manual (144 pages) ,
- Module manual (128 pages) ,
- Hardware manual (122 pages)
Table of Contents
Advertisement
RSP720 with 10GE Uplink Ports
RSP720 with 10GE Uplink Ports
Cisco IOS Release 12.2SRC introduces a new RSP720 with 10 Gigabit Ethernet (GE) uplink ports
(RSP720-10GE). The Cisco 7600 RSP720-10GE consists of a full-size board and two integrated
daughter cards: an MSFC4 and a PFC. The RSP720-10GE has an integrated switch fabric that
interconnects all of the line cards in the router with point-to-point 20-Gbps full-duplex serial channels.
Two versions of the RSP720-10GE module are available:
•
•
Because of physical differences between the RSP720 and RSP720-10GE (such as the CPU memory map
and ASIC operation), there are several configuration guidelines and restrictions you should be aware of.
See the
Following are the total power requirements for the RSP720-10GE:
•
•
Figure 2-2
See
Figure 2-2
Disk LEDs
RSP720-3C-10GE
RSP720 WITH INTERATED SWITCH FABRIC/PFC3C-10GE
Use Category 5 Shielded Twisted Pair cable at the port that supports the10/100/1000-Mbps RJ-45
Note
connector.
RSP720-10GE Features
The RSP720-10GE provides all of the features of the RSP720 and also provides the following benefits:
•
Note
Use CAT5 Shielded Twisted Pair cable at the port that supports the10/100/1000-Mbps RJ-45 connector.
•
Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide
2-8
RSP720-3C-10GE
RSP720-3CXL-10GE
"RSP720-10GE Usage Guidelines and Limitations" section on page 2-10
RSP720-3C-10GE = 355 watts (total power)
RSP720-3CXL-10GE = 378 watts (total power)
shows the RSP720-3C-10GE front panel. The RSP720-3CXL-10GE front panel is similar.
Table 2-2
and
Table 2-3
for information about the front-panel controls and LEDs.
RSP720-3C-10GE Front Panel
1-GE uplink
ports
DISK 0
EJECT
SFP
1
STATUS SYSTEM ACTIVE PWR MGMT
RESET
LINK
STATUS
LEDs
CompactFlash
LINK
LEDs
Type II slots
The RSP720-10GE has two 10GE uplink ports and three 1GE uplink ports. You can use the 10GE
ports as high-bandwidth uplinks and save chassis slots for high-density interfaces, such as a
SIP/SPA. This is especially useful in smaller chassis and in redundant configurations. For the three
1GE uplink ports, two ports support 1-Gbps SFP modules and one port supports a 10/100/1000-Mbps
RJ-45 connector.
The RSP720-10GE supports the following line rates for uplink traffic and backplane forwarding:
Chapter 2
10-GE uplink
CONSOLE
port
UPLINK
4
10/100/100
3
3
CONSOLE
LINK
LINK
LINK
10/100/1000
uplink port
Route Switch Processors and Supervisor Engines
for details.
ports
10GE UPLINK
5
LINK
LINK
LEDs
OL-10100-04
- Quick Links:
- Supported Hardware
Hide quick links:
Advertisement
Table of Contents
