Recalling A Snapshot; Snapshot Demonstration - Sony DFS-700 Service Manual
Dme switcher, digital/analog input board, analog composite input board, digital multi effects board, 3d video mapping effects board
Hide thumbs
Also See for DFS-700:
- Operating instructions manual (212 pages) ,
- Specifications (8 pages)
Table of Contents
Advertisement
Snapshots
Recalling a Snapshot
To recall a snapshot, use the following procedure.
TITLE
1
EDITOR
LUM
LUM
GPI
CRK
CRK
SET UP
MASK
MASK
SHIFT
CCR
LIGHTING
CCR
AUXILIARY
BLACK
1
BACKGROUND
BLACK
1
FOREGROUND
1
BLACK
1
To leave the primary cross-point bus section settings unaltered, press
the HOLD INPUT button, turning it on.
2
Press the RECALL button.
The button lights, and the pattern/numeric keypad is ready to accept a
snapshot number.
3
With the buttons 0 to 9, enter the snapshot number you want to recall.
You can use the UP and DOWN buttons to adjust the number
displayed.
4
Press the ENTER button.
This recalls the specified snapshot, and the control panel settings all
change correspondingly.
If, however, you turned the HOLD INPUT button on in step 1, the
settings of the primary cross-point bus section do not change.
Direct Snapshot Recall
You can recall snapshots 0 to 9 with a single button operation.
4-22
Chapter 4 Advanced Operations
SNAP SHOT number display
USER PGM
SNAP SHOT
DSK
EDGE
2
STATUS EDIT
2
LUM
TRAIL
SHADOW
BORDER BEVELD
EDGE
INITIAL
EDIT
LEARN
MASK
SOFT
1
RECALL
MATTES
BORDER
PATTERN
PAGE
F1
F2
F3
F4
F5
HOLD
LOCATION
ADJ
INPUT
EFFECT
TRANS RATE
DSK
PATTERN NUMBER
FTB
SET
SET
TITLE 1
TITLE 2
DSK
SUPER BG FRGD 2 MEMORY
FRAME
FREEZ
MIX
EFFECT
N/R
REV
DIRECT
DIRECT
DSK PVW
SOURCE
SOURCE
FILL
RECALL
PATTERN
LAST X
FADE
TO
7
8
9
BLACK
2
3
4
5
6
7
8
MEMORY
INT
TITLE
INS
3
VIDEO
4
5
6
DEL
INT
2
3
4
5
6
7
8
MEMORY
CUT
VIDEO
P IN P
DSK
1
2
3
RST
4
DOWN
UP
ENTER
0
AUTO
2
3
4
5
6
7
8
INT
MEMORY
TRANS
VIDEO
PATTERN/KEY PAD
Use the following procedure.
1
In the pattern/numeric keypad, press the DIRECT RECALL button,
turning it on.
This switches to direct recall mode.
2
Press the one of buttons 0 to 9 corresponding to the snapshot you want
to recall.
This recalls the snapshot.
To cancel the snapshot recall operation
In step 4, press the LEARN button instead of the ENTER button. The
LEARN button goes out and the operation is canceled.
Returning to the previous image with the LAST X function
To return to the state before recalling a snapshot, use the following
procedure.
1
Press the RECALL button in the snapshot section, turning it on.
Alternatively, press the DIRECT RECALL button, turning it on.
2
Hold down the ENTER button in the pattern/numeric keypad, and
press the LAST X button.
Snapshot Demonstration
You can automatically show all of snapshots 0 to 99 in sequence.
You can use this function for checking the snapshots, and also in the same
manner as the factory setting demonstration (see page 3-8).
The snapshot registers and factory setting demonstration registers are
separate. Even after changing the settings in the snapshot registers, you can
still run the factory setting demonstration unchanged.
To start the demonstration
Hold down buttons 1 and 9 in the pattern/numeric keypad, and press the
AUTO TRANS button in the effect transition section.
This plays back the snapshots in sequence, starting from the snapshot
whose number is specified at the time. During the demonstration, the
buttons on the pattern/numeric keypad light in turn in the clockwise
direction.
• The HOLD INPUT button setting also applies to the demonstration.
• During the demonstration, the control panel does not accept any
operations other than pressing the AUTO TRANS button.
To end the demonstration
Press the AUTO TRANS button once more.
4-23
Chapter 4 Advanced Operations
- Quick Links:
- Manual Structure
Hide quick links:
Advertisement
Table of Contents
