Intended use Cleaning and maintenance . . . 23 Intended use Overall condition of the machine . . . 23 I n t e n d e d u s e Special salt and rinse aid ..23 This appliance is intended for Filters .
Safety instructions Delivery The electrical connection conditions must correspond 1. Check the packaging and with the specifications dishwasher immediately for on the dishwasher rating plate 92. damage caused in transit. Do not switch on a damaged If the power cord of this appliance, but contact your appliance is damaged, supplier.
Safety instructions If you cannot obtain any In daily use information from Read and observe the safety the manufacturer, you must information and instructions not install the dishwasher for use on the packaging above or below these for cleaning and rinsing agents. appliances.
Safety instructions Disposal Warning Risk of explosion! 1. Make redundant appliances Do not add any solvents unusable to prevent to the washing chamber. subsequent accidents. Danger of explosion! 2. Dispose of the appliance in a n environmentally friendly Warning manner. Risk of scalding! Warning Open the door carefully when...
Protection of the environment Ensure that children do not Protection of the place fingers in the tablet environment collecting tray 12. Small fingers could become i o n P r o t e c t o f t e n v i r o n m e n t caught in the slots.
Getting to know your appliance Appliance interior Getting to know your appliance 1" Top basket G e t t i t o k n o w y o u r a p p l i a n c 1* Knife shelf * Diagrams of the control panel 12 Tablet collecting tray and the interior of the appliance can be...
Water softening system/Special salt Setting 5. Press and hold down the START button @. 6. Rotate programme selector 8 until The amount of salt dispensed can be the salt refill indicator ` flashes. set in 4 stages depending on the hardness of your 7.
Water softening system/Special salt Using special salt Using detergents with salt component D e t e r g e n t s w i t h s a l t c o m p o n e n t Always refill with special salt immediately before switching on the If combined detergents with a salt appliance.
Rinse aid 3. Close cover until it clicks shut. Rinse aid 4. To prevent excessive foam formation R i n s e a i d during the next rinse cycle, remove any rinse aid which has run over with As soon as the rinse-aid refill indicator X is lit on the fascia, there a cloth.
Utensils Switching off rinse-aid refill Glass and utensil damage indicator Causes: If the rinse-aid refill indicator X is Glass type and glass production impaired (e.g. when using combined process. detergents containing rinse-aid Chemical composition of the component), it can be switched off. detergent.
Utensils Unloading the dishwasher Pans Bottom basket 1b To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
Utensils Cutlery basket Small accessories holder * S m a l l a c c e s s o r i e s h o l d e r You should always place cutlery * depending on model unsorted with the points downwards. Light-weight plastic accessories, e.g.
Utensils A djusting the height of the 3. To raise the basket, hold the basket A d j u s t i n g t h e h e i g h t o f t h e b a s k e t on the sides of the upper edge and basket * lift it up.
Detergent Adding detergent Detergent 1. If the detergent dispenser 9" is still D e t e r g e closed, press the lock 9* to open You can use tablets as well as powder the detergent dispenser. or liquid detergents for dishwashers, but never use washing up liquid.
Detergent Notes If the utensils are only lightly soiled, You will obtain optimum rinsing slightly less than the indicated amount and drying results by using solo of detergent is usually adequate. detergents and applying salt and rinse aid separately. Suitable detergents and care products If programmes are short, tablets can be purchased online may not have full cleaning effect...
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options Ï Programme selection Intensive zone * I n t e n s i v e z o n e You can select a suitable programme Perfect for a mixed load. You can wash according to the type of utensils and very soiled pots and pans in the lower degree of soiling.
Operating the appliance Switching on the appliance Operating the appliance 1. Turn on the tap fully. 2. Close the door. O p e r a t i i a n c e t h e a p p l 3. Switch on ON/OFF switch (. Programme data The Cleaning display )* flashes.
Operating the appliance End of programme T erminating the programme T e r m i n a t i n g t h e p r o g r a m m e (Reset) The programme has ended when the End display )"...
Cleaning and maintenance Never use a steam cleaner to clean your Cleaning and dishwasher. The manufacturer is not liable for any consequential damage. maintenance Regularly wipe the front of the appliance C l e a n i a n d n a n c e m a i n t e and fascia with a damp cloth;...
Cleaning and maintenance Filters Spray arms The filters 1R keep large foreign Limescale objects in the rinsing water away from and contaminants in the rinsing water the pump. These foreign objects may may block nozzles and bearings on the spray arms 1: occasionally block the filters.
Fault, what to do? 3. Remove the filters 1R. Fault, what to do? 4. Scoop out water, use a sponge if F a u l t , w h a t d o ? required. Experience has shown that you can 5.
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display h lights up. Tap turned off. Turn the tap on. Tap jammed or calcified. Turn the tap on. Flow rate must be min.
Page 27
Fault, what to do? Fault Cause Remedial action Displays flash. Door not closed properly. Close the door. Ensure that no objects (utensil, fragrance dispenser) are protruding over the basket and preventing the door from closing. Refill indicator for salt ` No rinse aid.
Page 28
Fault, what to do? Fault Cause Remedial action Cutlery not dry. Cutlery not arranged properly in Separate cutlery if possible, prevent contact the cutlery basket. points. Cutlery not arranged properly in Arrange cutlery properly and separate if the cutlery drawer. possible.
Page 29
Fault, what to do? Fault Cause Remedial action Detergent residue. Detergent dispenser cover Detergent dispenser cover must not be blocked by utensils and therefore obstructed by utensils. does not open fully. Do not place utensils or fragrance dispenser in the tablet collecting tray. Detergent dispenser cover Tablet must be inserted flat and not upright.
Page 30
Fault, what to do? Fault Cause Remedial action White, stubborn coatings; Detergent substances are Change detergent brand. limescale on the utensils, deposited. These coatings cannot Clean appliance mechanically. container or door. usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or Set water softening system according to water hardness greater than 8.9 instructions for use or top up salt.
Page 31
Fault, what to do? Fault Cause Remedial action Removable streaks on Too much rinse aid. Set rinse aid amount to lower setting. glasses, glasses with No rinse aid added or setting too Add rinse aid and check dosage metallic appearance and low.
Page 32
Fault, what to do? Fault Cause Remedial action Appliance cannot be set Appliance is in the programme. Perform reset (see “Terminating the (hardness, final rinse, ...). Appliance can be set at the start programme”) and set the appliance of the programme only. according to the instructions for use.
Customer service Customer service Installation and connection C u s t o m e r s e r v i c e If you are unable to rectify the fault, l a t i o n I n s t a l a n d c o n n e c t i please contact your customer service.
Installation and connection Safety instructions Installation Please follow the safety instructions The required installation dimensions can under “Installation”. be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the Delivery appliance is situated securely on the floor.
Installation and connection Drinking water connection Electrical connection 1. Fasten the drinking water connection Connect the appliance to an to the tap according alternating current only, ranging from to the installation instructions using 220 V to 240 V and 50 Hz or 60 Hz the enclosed parts.
Installation and connection Removing the appliance Protection against frost P r o t e c t i o n a g a i n s t f r o s t ( E m p t y i n g t h e a p p l i a n c e ) Also observe If the appliance is in a room where there the sequence of worksteps here.
Page 38
*9000867503* 9000867503 en (9401) 440EA...