Table of Contents
Advertisement
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For printed wiring boards)
(Measuring conditions voltage and waveform)
• b: Pattern from the side which enables seeing.
• Voltages and waveforms are measured between the measure-
(The other layers' patterns are not indicated.)
ment points and ground when camera shoots color bar chart of
• Through hole is omitted.
pattern box. They are reference values and reference wave-
• Circled numbers refer to waveforms.
forms.
• There are few cases that the part printed on diagram
(VOM of DC 10 MΩ input impedance is used.).
isn't mounted in this model.
• Voltage values change depending upon input impedance of VOM
• Chip parts.
used.)
Transistor
Diode
C
6
5
4
4
5
6
4
5
1
2
3
3
3
1. Connection
B
E
1
2
3
3
2
1
3
2
1
5
4
3
2
1
2
1
2
1
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µµF.
50V or less are not indicated except for electrolytics and
tantalums.
• Chip resistors are 1/10W unless otherwise noted.
kΩ=1000Ω, MΩ=1000kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Be-
cause it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
2. Adjust the distance so that the output waveform of Fig. a and
Kinds of capacitor
the Fig. b can be obtain.
Temperature characteristics
External dimensions (mm)
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name
XEDIT → EDIT PB/XREC → PB/REC
Fig. a (Video output terminal output waveform)
• 2 : non flammable resistor
• 1 : fusible resistor
• C : panel designation
• A : B+ Line
• B : B– Line
• J
: IN/OUT direction of (+,–) B LINE.
• C : adjustment for repair.
• Circled numbers refer to waveforms.
Note :
Note :
Fig.b (Picture on monitor TV)
The components identified by
Les composants identifiés par
mark ! or dotted line with mark
une marque ! sont critiques
! are critical for safety.
pour la sécurité.
When indicating parts by reference number, pleas include
Replace only with part number
Ne les remplacer que par une
specified.
pièce portant le numéro spécifié.
the board name.
4-7
CD-209 BOARD
C1401
A-2
C1405
A-1
C1406
A-1
C1407
B-2
C1408
B-2
C1409
B-1
C1410
B-1
C1411
B-2
C1412
B-1
CN1401 A-3
IC1401 A-3
IC1402 B-2
L1401
A-2
Pattern box
L1402
B-1
R1401 A-1
R1405 A-1
R1406 B-2
R1407 B-2
R1408 B-2
1.5 m
R1409 B-1
Front of the lens
H
A
B
A=B
B
A
Electron beam
scanned frame
For printed wiring boards
• This board is six-layer print board. However, the pat-
CRT picture frame
terns of layers two to five have not been included in
the diagram.
There are few cases that the part printed on this
diagram isn't mounted in this model.
CD-209
(CCD IMAGER)
VF-129
(B/W EVF)
VL-23
(VIDEO LIGHT)
DD-117
(DC/DC CONVERTER)
PJ-92
(AV IN/OUT)
SE-83
(STEADY SHOT)
CD-209 (CCD IMAGER) PRINTED WIRING BOARD
— Ref. No. CD-209 Board; 10,000 Series —
CD-209
BOARD
CAMERA REC
1
2
IC1401 1,2
IC1401 3,4
6.8Vp-p
H
MA-351
(STEREO MIC AMP, LASER LINK)
4-8
3
4
5
IC1401 7
IC1401 !™
IC1401 !£,!¢
6.8Vp-p
3.3Vp-p
H
14.318 MHz
1.1Vp-p
H
CCD-TRV63/TRV66/TRV66PK
6
IC1402 6
3.7Vp-p
14.318 MHz
1.2Vp-p
H
CCD IMAGER
4-9
CD-209
Hide quick links:
Advertisement
Table of Contents
