Table of Contents
Advertisement
HCD-DZ530/DZ630
SERVICE MANUAL
Ver. 1.0 2007.03
HCD-DZ530/DZ630 are the amplifier, DVD/CD and
tuner section in DAV-DZ530/DZ630.
This system incorporates with Dolby* Digital and Dolby Pro Logic (II)
adaptive matrix surround decoder and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic", and the double-D symbol are trademarks of
Dolby Laboratories.
** Manufactured under license from DTS, Inc.
"DTS" and "DTS Digital Surround" are registered trademarks of DTS,
Inc.
Amplifier section
Stereo mode (rated)
108 W + 108 W (at 3 ohms,
1 kHz, 1 % THD)
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*: 142 watts
(per channel at 3 ohms, 1
kHz, 10 % THD)
Subwoofer*: 140 watts (at
3 ohms, 80 Hz, 10 % THD)
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
TV (AUDIO IN)
Sensitivity: 450/250 mV
LINE (AUDIO IN)
Sensitivity: 450/250 mV
AUDIO IN
Sensitivity: 250/125 mV
Outputs (Analog)
Phones
Accepts low-and high-
impedance headphones.
DVD system
Laser
Semiconductor laser
(DVD: λ = 650 nm)
(CD: λ = 790 nm)
Emission duration:
continuous
Signal format system
PAL/NTSC
Sony Corporation
9-887-598-01
Home Audio Division
2007C16-1
Published by Sony Techno Create Corporation
© 2007.03
Photo : HCD-DZ530
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Tuner section
System
PLL quartz-locked digital
synthesizer
FM tuner section
Tuning range
87.5-108.0 MHz (50 kHz
step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
531 – 1,602 kHz (with the
interval set at 9 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Video section
Outputs
VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
/C
, P
B
B
R
75 ohms
R/G/B: 0.7 Vp-p 75 ohms
HDMI OUT: Type A (19
pin)
General
Power requirements
Power output (DIGITAL MEDIA PORT)
Power consumption
Dimensions (approx.)
Mass (approx.)
Design and specifications are subject to change
without notice.
/C
: 0.7 Vp-p
R
DVD RECEIVER
AEP Model
HCD-DZ530/DZ630
UK Model
HCD-DZ630
HCD-DZ230
CDM85-DVBU102
KHM-313CAA
220 – 240 V AC, 50/60 Hz
DC OUT: 5 V, 700 mA
On: 150 W
Standby: 0.3 W (at the
Power Saving mode)
430 × 63 × 380 mm (w/h/d)
incl. projecting parts
4.2 kg
Advertisement
Table of Contents
Related Manuals for Sony HCD-DZ530
Summary of Contents for Sony HCD-DZ530
-
Page 1: Service Manual
HCD-DZ530/DZ630 UK Model HCD-DZ630 Ver. 1.0 2007.03 Photo : HCD-DZ530 HCD-DZ530/DZ630 are the amplifier, DVD/CD and tuner section in DAV-DZ530/DZ630. This system incorporates with Dolby* Digital and Dolby Pro Logic (II) Model Name Using Similar Mechanism HCD-DZ230 adaptive matrix surround decoder and the DTS** Digital Surround System. - Page 2 WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. Flexible Circuit Board Repairing REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE • Keep the temperature of the soldering iron around 270 °C PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR during repairing.
- Page 3 [VER.X.XX] (X is a number) may appear on the TV screen. Although this is not a malfunction and for Sony service use only, normal system operation will not be possible. Turn off the system, and then turn on the system again to operate.
-
Page 4: Table Of Contents
HCD-DZ530/DZ630 TABLE OF CONTENTS SERVICING NOTE 6-8. Schematic Diagram – MAIN Board (1/9) – ....37 ........... 5 6-9. Schematic Diagram – MAIN Board (2/9) – ....38 6-10. Schematic Diagram – MAIN Board (3/9) – ....39 GENERAL ..............9 6-11. -
Page 5: Servicing Note
HCD-DZ530/DZ630 SECTION 1 SERVICING NOTE Note about CDs/DVDs NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK The system can play CD-ROMs/CD-Rs/CD-RWs recorded in the OR BASE UNIT following formats: – audio CD format The laser diode in the optical pick-up block may suffer electrostatic –... - Page 6 HCD-DZ530/DZ630 How to open the disc table when power switch turns off Insert a tapering driver into the aperture of the unit bottom, and slide it in the direction of the arrow. Peel off the seal and so the lever is moved in the direction of the arrow with the thin rod.
- Page 7 Parts that require fixing using adhesive agent The following parts on the POWER board and on the MAIN board must be fixed by using the adhesive agent (such as Sony Bond Master) as it is specified by Safety Regulations. When any part or printed circuit board is replaced during repair work, be sure to confirm that the following capacitors and resistors are fixed by using the adhesive agent (such as Sony Bond Master) without fail.
- Page 8 HCD-DZ530/DZ630 Attention of the direction at replacement Please defend and install the direction of the below fig in the following parts on the POWER board. mark this side L931 POWER BOARD LF902 LF901 R912 R912 Precaution when installing a new OP unit /...
-
Page 9: General
HCD-DZ530/DZ630 SECTION 2 GENERAL This section is extracted from instruction manual. Front panel A "/1 (on/standby) (31) G VOLUME control (31) B A (open/close) (31) H PHONES jack (31) C Disc operation (31) I AUDIO IN/A.CAL MIC jack (20, 29) - Page 10 HCD-DZ530/DZ630 Front panel display About the indications in the front panel display A Lights up when the HDMI OUT jack is I Current repeat mode (43) correctly connected to HDCP (high- J Lights up when the child lock function bandwidth digital content protection) is set to on.
-
Page 11: Remote Control
HCD-DZ530/DZ630 Remote control ALPHABETICAL ORDER BUTTON DESCRIPTIONS [/1 (on/standby) 1 A – O P – Z TV [/1 (on/standby) ej ANGLE 5 PICTURE NAVI 6 C/X/x/c/ AUDIO 4 PRESET +/– wk es REPLAY/ CLEAR ef SOUND FIELD qh ADVANCE 9 D.TUNING wf... -
Page 12: Disassembly
HCD-DZ530/DZ630 SECTION 3 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. 3-2. CASE (DS), FRONT PANEL ASSY (Page 13) 3-5. DMPORT BOARD, 3-10. DVD MECHANISM DECK 3-8. SPEAKER BOARD, 3-3. FL BOARD TUNER (FM/AM) (CDM85-DVBU102) D.C. -
Page 13: Case (Ds), Front Panel Assy
HCD-DZ530/DZ630 Note: Follow the disassembly procedure in the numerical order given. 3-2. CASE (DS), FRONT PANEL ASSY 5 two screws (CASE3 TP2) Route the harness as shown below. 7 five screws (+BVTP 3 × 8) harness notch 8 case (DS) -
Page 14: Fl Board
HCD-DZ530/DZ630 3-3. FL BOARD 7 wire (flat type) 21core (CN801) 6 wire (flat type) 13core (CN805) 8 FL board 5 two screws (+BVTP 2.6 × 10) 4 shield plate (FR) 3 five screws (+BVTP 2.6 × 10) wire (flat type) 13core... -
Page 15: Jack Board, P-Sw Board
HCD-DZ530/DZ630 3-4. JACK BOARD, P-SW BOARD 7 button (base) q; P- SW board 6 screw (+BVTP 2.6 × 10 ) harness 1 knob (vol) 4 button (base) 2 nut 5 wire (flat type) 13core (CN806) Remove the solderings. qa JACK board 3 four screws (+BVTP 2.6 ×... -
Page 16: Io-Scart Board
HCD-DZ530/DZ630 3-6. IO-SCART BOARD 8 wire (flat type) 6 three screws (+BV 3 × 6 ) 11core (CN305) 7 wire (flat type) 9core (CN301) 9 IO-SCART board 5 four screws (+BVTP 3 × 8 ) 4 connector 4p (CN302) 2 wire (flat type) -
Page 17: Speaker Board, D.c. Fan
HCD-DZ530/DZ630 3-8. SPEAKER BOARD, D.C. FAN 3 two screws (+BV 3 × 6 ) 7 D.C. fan 4 SPEAKER board 2 screw (+BVTP 3 × 8 ) 1 connector 5 connector 8p (CN303) 2p (CN3000) 6 two screws (+BVTT 4 × 8 ) -
Page 18: Main Board
HCD-DZ530/DZ630 3-9. MAIN BOARD 6 screw (+BVTP 3 × 12) Attaching the two radiation sheets 5 two screws (+BV 3 × 10) on the IC MAIN board first, and then attach the heatsink (AMP). 7 heatsink (AMP), HEATSINK B board,... -
Page 19: Dvd Mechanism Deck (Cdm85-Dvbu102)
HCD-DZ530/DZ630 3-10. DVD MECHANISM DECK (CDM85-DVBU102) 1 wire (flat type) 9 three screws (+BV 3 × 6) 2 unweaved 5core (CN307) cloth q; cover (MD) 3 Remove the wire. 8 Remove the wire and harness. qa three screws (+BV 3 × 6) -
Page 20: Belt, Ms-203 Board
HCD-DZ530/DZ630 3-12. BELT, MS-203 BOARD 2 chuck cam 3 belt 4 screw (M 1.7 × 2.5) 1 two claws 7 MS-203 board 6 DC motor 5 three claws... -
Page 21: Optical Pick-Up (Khm-313Caa)
HCD-DZ530/DZ630 3-13. OPTICAL PICK-UP (KHM-313CAA) 3 two claws 2 chuck cam 1 two claws 4 base unit 8 two insulators 6 four insulator screws 9 two insulators 0 optical pick-up (KHM-313CAA) 5 two claws 7 bu holder... -
Page 22: Test Mode
HCD-DZ530/DZ630 SECTION 4 TEST MODE 3. Disc Tray Lock Note: Incorrect operations may be performed if the test mode is not The disc tray lock function for the antitheft of an demonstration entered properly. disc in the store is equipped. - Page 23 HCD-DZ530/DZ630 7. Volume Test 9. Automatic Acoustic Field Calibration Microphone Procedure: Test Mode 1. Press the button to turn the power on. Procedure: 2. Press three buttons . , H and > simultaneously. 1. Press the ?/1 button to turn the power on.
- Page 24 HCD-DZ530/DZ630 (2) Select “2. Drive Manual Operation” by pressing the 2 button DVD SECTION on the remote commander. The screen will appear as shown. 11. General Description Drive Manual Operation The IOP measurement allows you to make diagnosis and adjustment 1.
- Page 25 HCD-DZ530/DZ630 14. Emergency History 52: Open kick spindle error To check the emergency history, please follow the following 51: Spindle stop error procedure. 60: Focus on error 61: Seek fail error (1) From the Top Menu of Remocon Diagnosis Menu, select “3.
- Page 26 HCD-DZ530/DZ630 14-4. Return to the Top Menu of Remocon Diagnosis Menu Press 0 button on the remote commander. • Check Version Information To check the version information, please follow the following procedure. (1) From the Top Menu of Remocon Diagnosis Menu, select “4.
-
Page 27: Electrical Adjustment
HCD-DZ530/DZ630 SECTION 5 ELECTRICAL ADJUSTMENT DVD SECTION When the optical pick-up assy is replaced, perform the “Executing IOP Measurement”. Executing IOP Measurement (See page 24) TUNER SECTION [FM Tune Level Check] generator OUT (75 Ω ) Procedure: 1. Turn the power on. -
Page 28: Diagrams
HCD-DZ530/DZ630 SECTION 6 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams. For Printed Wiring Boards. Note: Note: • All capacitors are in μF unless otherwise noted. (p: pF) •... -
Page 41: Schematic Diagram - Main Board (5/9)
IC3400 CXD9883M IC3300 CXD9883M... -
Page 42: Schematic Diagram - Main Board (6/9)
1 6 . 5... -
Page 48: Schematic Diagram - Io-Scart Board
31 30 32 31 30... - Page 57 HCD-DZ530/DZ630 – MAIN Board – IC772 PCM1808PWR Serial LRCK Interface DOUT Mode/ Format Control Clock Timing SCKI Control × 1/64 Decimation Filter with HighúPass Filter DGND DeltaúSigma DeltaúSigma Modulator Modulator Power Supply Antialias AGND VINL Reference VREF Antialias VINR – IO-SCART Board –...
- Page 58 HCD-DZ530/DZ630 – IO-SCART Board – IC201, IC230 BH7868FS-E2 6MHz VCC1 75Ω 32 C OUT S-DC OUT 31 S-DC OUT S1/S2 C IN BIAS MUTE1 MUTE1 6MHz 75Ω CV OUT CV IN CLAMP CV OUT SAG SEL (CV/MIX) 6MHz Y IN CLAMP 75Ω...
-
Page 59: Dmport Board
HCD-DZ530/DZ630 – FL Board – IC802 uPD16315GB-3BS Grid driver Multiplexed driver SEG19/GRID10 Command decoder LED1 SEG18/GRID11 LED2 Display memory LED3 SEG17/GRID12 24 bits x 12 words LED4 Timing generator key scan DOUT SEG16/KS16 Key data memory Serial SEG15/KS15 (2 x 16 bits) - Page 60 HCD-DZ530/DZ630 • IC Pin Function Description MAIN BOARD IC1101 CXD9889R (CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGTAL SERVO PROCESSOR) Pin No. Pin Name Description AGND — Ground terminal DVDA AC coupled input path A DVDB AC coupled input path B...
- Page 61 HCD-DZ530/DZ630 Pin No. Pin Name Description RESERVED — USB port DMINUS pin for HS DL (not used (Open)) USB_VDD3 — Power supply (SW+3.3V) SPFG Spindle FG input DVD/CD switch (H:DVD / L:CD) CKSW CKSW input OCSW OCSW input EEWP EEPROM Write Protect control (L:Write allowed) DVDD18 —...
- Page 62 HCD-DZ530/DZ630 Pin No. Pin Name Description RWE# Write enable output to SDRAM (IC1104) CAS# Column address strobe output to SDRAM (IC1104) RAS# Row address strobe output to SDRAM (IC1104) RCS# Chip select output to SDRAM (IC1104) 137, 138 BA0, 1...
- Page 63 HCD-DZ530/DZ630 Pin No. Pin Name Description SCORE Calculation of SCORE (not used (Fixed to Ground)) Detection of MIC signal (H:Voice exist / L:Voice is absence) XVOICE (not used (Fixed to Ground)) Fixed_Low — Not used (Open) ASDATA1 Audio serial data 1: SL/SR...
- Page 64 HCD-DZ530/DZ630 Pin No. Pin Name Description RFRPDC RF ripple detect output RFRPAC RF ripple detect input (through AC-coupling) HRFZC High frequency RF ripple zero crossing CRTPLP Defect level filter capacitor connecting RFGND18 — Ground terminal RF offset cancellation capacitor connecting...
- Page 65 HCD-DZ530/DZ630 MAIN BOARD IC501 M30622MEP-B02FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description DAMP_SCDT/ DAMP processor data output DIAT_SDATA/DIR_DIN DAMP_SHIFT/ DAMP processor clock output DIAT_SCLK/DIR_CLK CEC_RX_IN CEC data input SIRCS_IN Sircs input NO USE Not used (Open) NO USE Not used (Open)
- Page 66 HCD-DZ530/DZ630 Pin No. Pin Name Description DAMP LATCH2 DAMP processor latch2 DAMP LATCH3 DAMP processor latch3 DAMP INIT DAMP processor reset DAMP SOFT MUTE DAMP processor soft muting HP_SW Headphone detect HP_MUTE Headphone muting NO USE Not used (Open) NO USE...
- Page 67 HCD-DZ530/DZ630 Pin No. Pin Name Description KEY0 Key input 0 input VREF — Reference voltage (E3.3V) — Power supply (BUP+3.3V) NO USE Not used (Open)
-
Page 68: Exploded Views
HCD-DZ530/DZ630 SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied. -
Page 69: Front Panel Section
HCD-DZ530/DZ630 7-2. FRONT PANEL SECTION supplied supplied supplied supplied supplied supplied including S800 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-889-990-01 KNOB (VOL) A-1218-017-A JACK BOARD, COMPLETE 2-889-985-61 WINDOW, INDICATION (HM) (DZ630) 1-828-325-51 WIRE (FLAT TYPE) (13 CORE) -
Page 70: Chassis Section
HCD-DZ530/DZ630 7-3. CHASSIS SECTION supplied supplied supplied supplied supplied supplied supplied not supplied supplied DVD mechanism F901 deck section (CDM85-DVBU102) not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-077-331-21 +BV3 (3-CR) 0 110... -
Page 71: Dvd Mechanism Deck Section (Cdm85-Dvbu102)
HCD-DZ530/DZ630 7-4. DVD MECHANISM DECK SECTION (CDM85-DVBU102) not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-6071-669-A LOADING ASSY (M) -
Page 72: Electrical Parts List
HCD-DZ530/DZ630 SECTION 8 DMPORT ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, uH: μH parts list may be different from the parts please include the board name. specified in the diagrams or the components •... - Page 73 HCD-DZ530/DZ630 IO-SCART Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D805 6-501-193-01 DIODE 1SS355WTE-17 C215 1-126-933-11 ELECT 100uF C216 1-126-933-11 ELECT 100uF < IC > C221 1-107-826-11 CERAMIC CHIP 0.1uF C222 1-104-658-91 ELECT 100uF IC801 6-600-349-21 IC NJL23H400A...
- Page 74 HCD-DZ530/DZ630 IO-SCART Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > R244 1-218-285-11 METAL CHIP 1/10W R245 1-218-285-11 METAL CHIP 1/10W CN301 1-779-277-11 CONNECTOR, FFC (LIF (NON-ZIF)) 9P R246 1-218-285-11 METAL CHIP 1/10W CN302...
- Page 75 HCD-DZ530/DZ630 IO-SCART JACK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > R397 1-216-833-11 METAL CHIP 1/10W R398 1-216-841-11 METAL CHIP 1/10W D470 6-501-193-01 DIODE 1SS355WTE-17 R399 1-216-841-11 METAL CHIP 1/10W D492 6-501-193-01 DIODE 1SS355WTE-17...
- Page 76 HCD-DZ530/DZ630 JACK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R434 1-216-864-11 SHORT CHIP R435 1-216-857-11 METAL CHIP 1/10W C511 1-162-964-11 CERAMIC CHIP 0.001uF C515 1-107-826-11 CERAMIC CHIP 0.1uF R444 1-216-864-11 SHORT CHIP C516 1-165-908-11 CERAMIC CHIP...
- Page 77 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1137 1-107-826-11 CERAMIC CHIP 0.1uF C1138 1-162-964-11 CERAMIC CHIP 0.001uF C1214 1-162-964-11 CERAMIC CHIP 0.001uF C1139 1-162-919-11 CERAMIC CHIP 22PF C1215 1-162-970-11 CERAMIC CHIP 0.01uF C1217...
- Page 78 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3012 1-107-826-11 CERAMIC CHIP 0.1uF C3013 1-107-826-11 CERAMIC CHIP 0.1uF C3094 1-162-927-11 CERAMIC CHIP 100PF C3014 1-107-826-11 CERAMIC CHIP 0.1uF C3095 1-162-964-11 CERAMIC CHIP 0.001uF C3100 1-104-329-11 CERAMIC CHIP 0.1uF...
- Page 79 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3255 1-107-725-11 CERAMIC CHIP 0.1uF C3256 1-115-185-11 CERAMIC CHIP 0.033uF C9772 1-107-826-11 CERAMIC CHIP 0.1uF C3257 1-115-185-11 CERAMIC CHIP 0.033uF < CONNECTOR > C3258 1-104-329-11 CERAMIC CHIP 0.1uF...
- Page 80 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB1601 1-469-324-21 FERRITE, EMI (SMD) (2012) L3000 1-469-527-91 INDUCTOR 47uH L3051 1-414-754-11 INDUCTOR 10uH FB1602 1-469-324-21 FERRITE, EMI (SMD) (2012) L3052 1-414-754-11 INDUCTOR 10uH FB1603 1-469-324-21 FERRITE, EMI (SMD) (2012)
- Page 81 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R501 1-216-857-11 METAL CHIP 1/10W R577 1-216-841-11 METAL CHIP 1/10W R505 1-216-829-11 METAL CHIP 4.7K 1/10W R578 1-216-809-11 METAL CHIP 1/10W R506 1-216-839-11 METAL CHIP 1/10W...
- Page 82 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1205 1-216-833-11 METAL CHIP 1/10W R785 1-216-801-11 METAL CHIP 1/10W R1206 1-216-833-11 METAL CHIP 1/10W R786 1-216-295-91 SHORT CHIP R1207 1-216-826-11 METAL CHIP 2.7K 1/10W R790...
- Page 83 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R2505 1-216-864-11 SHORT CHIP R1736 1-216-864-11 SHORT CHIP R2705 1-216-821-11 METAL CHIP 1/10W R1738 1-216-864-11 SHORT CHIP R2706 1-216-821-11 METAL CHIP 1/10W R1740 1-216-864-11 SHORT CHIP...
- Page 84 HCD-DZ530/DZ630 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R3251 1-216-809-11 METAL CHIP 1/10W R3069 1-216-809-11 METAL CHIP 1/10W R3252 1-216-809-11 METAL CHIP 1/10W R3070 1-216-809-11 METAL CHIP 1/10W R3253 1-216-864-11 SHORT CHIP R3071 1-216-809-11 METAL CHIP...
- Page 85 HCD-DZ530/DZ630 MAIN MS-203 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MS-203 BOARD, COMPLETE R4515 1-216-805-11 METAL CHIP 1/10W *********************** R4516 1-216-805-11 METAL CHIP 1/10W R4517 1-216-864-11 SHORT CHIP < CONNECTOR > R4519 1-216-864-11 SHORT CHIP...
- Page 86 HCD-DZ530/DZ630 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C958 1-162-970-11 CERAMIC CHIP 0.01uF < IC > C960 1-162-970-11 CERAMIC CHIP 0.01uF 0 C963 1-117-697-51 CERAMIC 470PF 250V 0 IC901 6-707-742-01 IC STR-F6168-LF1352 0 IC921...
- Page 87 HCD-DZ530/DZ630 POWER P-SW SPEAKER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R932 1-218-883-11 METAL CHIP 0.5% 1/10W SPEAKER BOARD R933 1-216-829-11 METAL CHIP 4.7K 1/10W ************** R934 1-216-821-11 METAL CHIP 1/10W R935 1-216-821-11 METAL CHIP 1/10W <...
-
Page 88: Revision History
HCD-DZ530/DZ630 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...