Advertisement
Quick Links
Safety instructions
- The washing machine is heavy caution when lifting it.
- Warning: Frozen hoses may tear/burst. Do not install washing machine in areas where there
is a risk of frost and/or outdoors.
- Washing machine may be damaged. Do not lift by projecting components (e.g. washing
machine door).
- In addition to the instructions mentioned here, special regulations of the relevant water
and power supply companies may apply.
- If in doubt, have the appliance connected by a technician.
- Lay hoses and cables in such a way that there is no risk of stumbling.
Humidity in the drum
Scope of delivery
is caused by the final
according to model
Model:
Aqua Stop
Aqua Secure
Standard
Power cord
Water drainage
Water supply
Wrench (according to model)
Covers
Elbow
for fixing the waste water
hose
Depending on the connection
- 1 hose clip
24-40 mm (specialist outlet) for connection of the siphon is also required ->
page 4; Water connection.
Useful tool
- Spirit level for alignment.
Installation area
- Stability is important to prevent the machine from wandering!
- The installation area must be firm and level.
- Soft floors/floor coverings are not suitable.
If installing the appliance on a base
- The feet of the appliance must be secured with holding brackets;
order no. WMZ 2200, WX 9756, CZ110600, Z 7080X 0.
If installing the appliance on a wooden joist
- If possible, install the washing machine in a corner.
- Screw a water resistant wooden panel (min. 30 mm thick) to the floor.
- The feet of the appliance must be secured with holding brackets; order no. see above.
Hose and cable lengths
depending on model
Connection on left side
or
100 cm
145 cm
145 cm
95 cm
inspection.
85 cm
*
Standard and Aqua Secure models: min. 60 cm max. 100 cm
Aqua Stop model: 0 max. 100 cm
Available from dealer/customer service:
- Extension for Aqua Stop and cold water inlet hose (approx. 2.50 m),
Order no. WMZ 2380, WZ 10130, CZ11350, Z 7070X 0.
- Longer supply hose (approx. 2.20 m), for standard model.
Built under/Built in appliance
Build under/build in before connection to the power supply.
Installed in between kitchen units
(built under or built in)
- 60 cm cavity width required.
- Install washing machine only under a continuous worktop connected
firmly to the adjacent cupboards.
Built under appliance
Risk of electric shock!
- 60 cm cavity width required.
- Instead of the appliance cover panel, have a technician install a sheet
metal cover * (* order no. WMZ 2420, WZ 10190).
1
Remove transportation protection
devices
Connection on right side
- Before using the appliance for the first time, remove all the transportation
protection devices and retain for subsequent transportation of the
appliance.
- For any future transport, the transport braces must be refitted this
prevents the machine from being damaged. -> page 6.
- Keep the bolt and sleeve screwed together.
1. Take the hoses and elbow out of the holders, depending on model.
135 cm
2. Loosen the bolts ....
... until they are freely movable in the sleeves.
3. Completely remove all 4 transportation protection devices and
take the mains cable out of the holder.
4. Insert covers.
2
Water connection
depending on model
- Risk of electric shock! Do not immerse Aqua Stop safety device in water
(contains an electric valve).
- To prevent leakage or water damage, follow the instructions in this chapter!
- Attention: Operate the washing machine with cold drinking water only.
Do not connect to a mixer tap of a pressureless hot water heater.
- Do not use a used inlet hose. Only use the inlet hose supplied or one which was purchased
from an authorised specialist dealer.
- If in doubt, have the appliance connected by a technician.
Water supply
Water supply hose:
Attention: Do not kink, crush, modify or sever water supply hose
(strength is no longer guaranteed).
Optimum water pressure in the mains: 100-1000 kPa (1-10 bar)
- When the tap is turned on, the water flow is at least 8 l/min.
- If the water pressure is higher, install a pressure reducing valve.
Model:
Aqua Stop
Aqua Secure
1. Connect water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Open water tap carefully, checking the leak tightness
max.
of the connection points.
90_
Attention: Screw fitting is under mains water
pressure.
min. 10 mm
Water drainage
Water drainage hose:
Attention: Do not kink or protract the drainage hose.
Height difference between installation area and outlet:
- min. 60 cm - max. 100 cm for aqua secure and standard models
- 0 - max. 100 cm for aqua stop model
Drainage into a washbasin:
Attention: Secure the drainage hose from slipping out.
Attention: The washbasin outlet must not be sealed by the plug.
Check that the water is pumped out quickly enough. Do not insert the end
of the drainage hose into the pumped off water! There is a risk that water
will be drawn back into the washing machine!
Drainage into a siphon:
Attention: Secure connection point with hose clip,
24-40 mm (dealer).
3
Standard
3/4"
min. 10 mm
max.
90_
3/4"
4
Advertisement
Related Manuals for Bosch WAE24166GB
Summary of Contents for Bosch WAE24166GB
- Page 1 Safety instructions Hose and cable lengths Remove transportation protection Water connection depending on model depending on model devices - The washing machine is heavy caution when lifting it. - Risk of electric shock! Do not immerse Aqua Stop safety device in water Connection on left side Connection on right side - Warning: Frozen hoses may tear/burst.
- Page 2 Alignment Transportation, e.g. if moving house Customer service Loud noise formation, intense vibrations and wandering" may be due to incorrect alignment! Before calling customer service, please check whether you can eliminate the fault yourself. -> operating instructions, What to do if ... Before transporting the washing machine: Align washing machine with spirit level.