Page 1
SSB RADIO TELEPHONE iC-m700pro S-14410XZ-C1 June. 2007...
Page 2
8. READ the instructions of test equipment throughly before connecting a test equipment to the transceiver. Icom, Icom Inc. and logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
SECTION 3 CIRCUIT DESCRIPTION 3-1 RECEIVER CIRCUITS 3-1-3 2ND MIXER AND IF CIRCUITS (MAIN UNIT) The 1st IF signal from the crystal filter (FI1b) is converted 3-1-1 RF FILTER CIRCUIT (MAIN UNIT) again into a 9.0115 MHz 2nd IF signal at the 2nd mixer Received signals from the antenna connector pass through circuit (D52, L66, L67).
Page 7
The detected voltage is also applied to the noise blanker 3-1-8 S-METER CIRCUIT (MAIN UNIT) AGC circuit (Q12, Q10) and is then fed back to the noise The S-meter indicates the AGC level on the display, since amplifier (IC8) as a bias voltage. The noise AGC circuit the AGC level varies with the received signal strength.
The comparator outputs “High” when the integrated signals The SSB signal from FI2 is amplified at the 9 MHz amplifi- exceed the reference voltage. C269, R310 and R780 are ers (Q17–Q19) and is then applied to the mixer circuit (D52). used as a time constant circuit.
Page 9
3-2-6 POWER AMPLIFIER CIRCUIT 3-2-7 ALC CIRCUIT The transceiver has two ALC (Auto Level Control) loops for (PA150W BOARD) constant output power over all marine bands and for high This circuit provides a stable 150 W (at 13.6 V) of output power setting.
3-2-8 APC CIRCUIT 3-3 PLL CIRCUIT The APC (Auto Power Control) circuit protects the power 3-3-1 GENERAL amplifiers on the PA unit from high SWR and excessive The PLL unit generates a 1st LO frequency (69.5115– current. 99.0114 MHz), 2nd LO frequency (60 MHz) and a BFO fre- quency (9.0106–9.013 MHz) for the MAIN unit.
3-4 PORT ALLOCATIONS 3-3-3 2ND LO AND REFERENCE OSCILLATOR CPU (MAIN unit; IC132) CIRCUITS The reference oscillator (X3001) generates 30.0 MHz fre- Port Description quency used for the both DDS ICs as a system clock and number name for the LO output. The oscillated signal is doubled at the Input port for the CPU reset signal.
Page 12
(MAIN unit; IC132)–Continued Port Description number name Outputs AF gain control signal to the control (IC36). Outputs the "tuner start" pulse to an STAT optional AT-130E. Outputs a BEEP signal (1 kHz or BEEP 500 Hz). Outputs a strobe signal to the main STB1 loop PLL IC (C3005).
Pin 1 MIC [PTT] Connect pins 3 and 4 CAUTION: for AF output DO NOT connect the signal generator while transmitting. to DC power receptacle DC power supply 13.6 V/30 A [ANT] [DC 13.6 V] IC-M700PRO to [MICROPHONE] 4 - 1...
4-2 PLL ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST REFERENCE • Display frequency : 7.9999 MHz Connect a digital 3.2 V C3049 LOOP LOCK • Mode : J3E m u l t i m e t e r VOLTAGE •...
Page 15
• MAIN AND PLL UNITS C3049 Reference loop lock voltage adjustment J3004 Reference loop lock voltage P3002 Reference check point frequency check point J3005 Main loop lock voltage check point L3004 Reference frequency L3003 adjustment L3024 Main loop L3005 lock voltage adjustment 4 - 3...
4-3 TRANSMITTER ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST R4022 IDLING • Display frequency : 12.2300 MHz Cut the lead wire 100 mA CURRENT • mode : J3E (W4011) and connect (For drive • Apply no audio signal to the a DC ammeter (1 A) transistors) [MICROPHONE] connector.
Page 17
• PA AND FILTER BOARDS IC APC check point Ammeter 7 8 9 DC power supply R4022 Idling current (for drive transistors) adjustment R4025 Idling current (for final transistors) W4011 Idling current adjustment (for drive transistors) check point Ammeter EP4003 EP4004 W4011 C4392...
Page 18
TRANSMITTER ADJUSTMENTS (continued) ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST MAIN R184 TRANSMIT • Display frequency : 12.2300 MHz Rear C o n n e c t a n R F 140 W GAIN • mode : A1A Panel power meter to the...
Page 19
• MAIN UNIT AND LOGIC BOARD L108 Tune power R159 preparation Transmit gain check point Transmit R205 Tune power gain adjustment R184 adjustment R184 Output power R211 adjustment R212 Carrier R239 suppression R238 adjustment R2066 Mic gain adjustment R2070 Mic limitter adjustment 4 - 7...
4-4 RECEIVER ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST RECEIVER • Display frequency : 2.1820 MHz Rear C o n n e c t a n A C Muximum output level MAIN Adjust in GAIN •...
Page 21
SECTION 5 PARTS LIST [FRONT UNIT] [LOGIC-J UNIT] ORDER ORDER DESCRIPTION DESCRIPTION S2801 2260001581 SW JPZ2120-0301F R2058 7010003101 RES PSD1/4V 3.3 R2061 7030000260 S.RES MCR10EZHJ 100 (101) R2062 7030000440 S.RES MCR10EZHJ 3.3 k SP2801 2510000441 SP F77G08-6205 (-13) R2063 7030000300 S.RES MCR10EZHJ 220 (221) R2064 7030000610 S.RES MCR10EZHJ 82 k R2065...
Page 51
Phone : +81 (06) 6793 5302 F ax : +81 (06) 6793 0013 : http://ww w .icom.c o .jp/ w o r ld/ind e x.html <Co r po r ate Headqua r ters> Com m unication Equipment 2380 116th A v e n ue N.E., Bell e vu e , W A 98004, U . S .A.