SANYO Factory Code N8ZFE Service Reference NO. 610 DP19640 SERVICE MANUAL 18.5" HDTV LCD TVHD ACL ORIGINAL MFR'S VERSION A Design and specifications are subject to change without notice.
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. PERFORM A SAFETY CHECK AFTER SERVICING As for the places which need special attentions, they are indicated with the labels or seals on the Confirm that the screws, parts and wiring which cabinet, chassis and parts.
ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.) Caution: • Pb free solder has a higher melting point than standard solder; Typically the melting point is 86 F~104 F(30...
TABLE OF CONTENTS A1-1 SERVICING NOTICES ON CHECKING……………………………………………………………………………….. A1-1 HOW TO ORDER PARTS………………………………………………………………………………………………. A1-1 IMPORTANT……………………………………………………………………………………………………………… A1-2 ABOUT LEAD FREE SOLDER (PbF)………………………………………………………………………………….. A2-1 TABLE OF CONTENTS…………………………………………………………………………………………………. A3-1~A3-6 GENERAL SPECIFICATIONS………………………………………………………………………………………….. DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS…………………………………………………. B1-1, B1-2 2.
GENERAL SPECIFICATIONS LCD Size / Visual Size 18.50 inch / 470.1mmV System LCD Type Color TFT LCD Number of Pixels 1366(H) x 768(V) Double Scan View Range Left/Right 85/85 degree Up/Down 80/80 degree < Bright Dot Zero Bright Dot Ratio Color System NTSC Speaker...
Page 6
Game Timer Timer Back-up (at Power Off Mode) more than Remote Unit RC-RU Control Glow in Dark Remocon Remocon Format SANYO Format Custom Code 38-C7h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys 28 Keys...
Page 7
GENERAL SPECIFICATIONS G-10 Features Auto Shut Off Auto Search Power On Memory Hotel Mode Comb Filter Game Position Auto Setup Language TV Location Signal Type Automatic Search Picture Setting(TV) Picture Preference Brightness , Contrast , Color Tint Sharpness Color Temperature Backlight Picture Setting(PC) HOR Position , VER Position...
Page 8
GENERAL SPECIFICATIONS Digital Out Dolby Digital MPEG PC Monitor Input VGA (640x480) Yes (60,72,75Hz) VGA (720x400) Yes (70Hz) WVGA (848x480) SVGA (800x600) Yes (56,60,72,75Hz) XGA (1024x768) Yes (60,70,75Hz) WXGA (1280x768) Yes (60Hz) WXGA (1280x720) Yes (60Hz) WXGA (1360x768) Yes (60Hz) SXGA (1280x1024) HDMI Input VGA (640×480)
Page 9
GENERAL SPECIFICATIONS G-11 Accessories Owner's Manual Language English / Spanish w/Guarantee Card Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet Quick Set-up Sheet...
Page 10
Sets/40' container w/Pallet w/Wrapping G-16 Material Cabinet Cabinet Front PC+ABS 94V0 NON-HALOGEN Rear PS 94V0 NON-DECABROM Stand PS 94HB Jack Panel Non-Halogen Demand Eyelet Demand G-17 Environment Environmental standard requirement Green procurement of SANYO Pb-free Phase3(Phase3A) Measures for Whisker Rohs A3-6...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: MAIN PCB and REMOCON PCB AND P.C. BOARDS (Refer to Fig. 1-3) 1. Disconnect the following connectors: CAUTION (CP2804, CP3001, CP4301 and CP6204). 2. Remove the 5 screws (1). Be careful not to remove the LVDS cable forcibly, because the LVDS cable may be damaged.
Page 12
DISASSEMBLY INSTRUCTIONS 1-5: SPEAKER ASS'Y AND LCD PANEL (Refer to Fig. 1-6) 1. Remove the screw (1). 2. Remove the Speaker Ass'y in the direction of arrow (A). 3. Remove the LCD Panel in the direction of arrow (B). LCD Panel (1) Speaker Ass'y Fig.
DISASSEMBLY INSTRUCTIONS 2. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after FLAT PACKAGE IC desoldering completely, pickup the corner of the IC using tweezers and remove the IC by moving with the IC REMOVAL desoldering machine.
Page 14
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a 1. Take care of the polarity of new IC and then install the Thintip Soldering Iron. (Refer to Fig. 2-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition.
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0".
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE NO. FUNCTION NO. FUNCTION Read and perform these adjustments when repairing the 03 R DRIVE(N) 35 TINT circuits or replacing electrical parts or PCB assemblies. 04 R CUTOFF(N) 36 SHARP H1 MAX 05 G DRIVE(N) 37 SHARP H1 MIN CAUTION 06 G CUTOFF(N)
Page 18
ELECTRICAL ADJUSTMENTS 2-2: BRIGHTNESS CENT 2-3: CONTRAST MAX 1. Place the set in Aging Test for more than 15 minutes. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the color bar pattern. (RF Input) 2.
Page 19
ELECTRICAL ADJUSTMENTS 2-4: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (TV/AV/COMPONENT/HDMI//PC/DTV) COMPONENT HDMI PC/HDMI-DVI FUNCTION CVBS 480i 480p 720p 1080i 480i 480p 720p 1080i 1080p 640x480 720x400...
Page 20
ELECTRICAL ADJUSTMENTS 3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) LCD PANEL POWER PCB CP7001 CP7002 MAIN PCB CD3001 J4206 J4306 TU5801 J501 CP6204 CP4301 SPEAKER CD7601 AC IN OS7601 CD501 REMOCON PCB...
WAVEFORMS FLASH 20ns 200mV 100mV SCALER VIDEO/AUDIO JACK 10s 0.5V 100mV 10s 200mV 100mV 10s 0.2s 100mV 200mV JACK2 10s 100mV 200mV 100mV 200mV NOTE : The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) SCREW POLYBAG INSTRUCTION INSTRUCTION BOOK(E/S) TM101 INFORMATION SHEET(PICTURE QUALITY) INFORMATION SHEET(RETURN) CD501 PACKAGE TOP FLIM BAG (791WHA0173) FLIM BAG (791WHA0189) PACKAGE BOTTOM CARTON LABEL GIFT BOX LABEL GIFT BOX...
MECHANICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION 7A708A372A FRONT CABI ASS'Y 101A 708WPA0035 CABINET FRONT 708WPAA092 CANINET FRONT 101B 713WPA0452 GLASS LED 101C 800WQ00181 FELT SHEET 7A702B185A BACK CABI ASS'Y 102A 702WPAB676 CABINET BACK 102B 721000A002 SHEET BUTTON 102C 735WPAB211 STOPPER BUTTON 102D...
Page 45
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION RESISTORS CAPACITORS R4263 R808R9750J OHM 1/16W C301 CS0PB0N16K CC UF 10V B R4265 R808R9750J OHM 1/16W C303 CS0PB0N16K CC UF 10V B R4316 R808R9153J 15K OHM 1/16W C304 E7ESU2101M CE 100 UF 16V...
Page 46
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION CAPACITORS CAPACITORS C2845 CS0UB0N15K CC 0.1 UF 10V B C2940 CS0UB0N15K CC 0.1 UF 10V B C2846 CS0UB0N15K CC 0.1 UF 10V B C2944 CS0UB0N15K CC 0.1 UF 10V B C2847 CS0UB0N15K CC...
Page 47
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION CAPACITORS DIODES C4343 CS0UCH4Q2J CC 470 PF 50V CH D7024 DGERMA1110 DIODE SILICON MA111-(TX) C4344 CS0UCH4Q2J CC 470 PF 50V CH D7601 0021E9Q010 LTL-1BEFJ-002A C5808 CS0UB0N15K CC 0.1 UF 10V B C5815 CS0UCH411J CC...