Related Manuals for Toro 72049
Summary of Contents for Toro 72049
- Page 1 Form No. 3322–962 Wheel Horse 265–6 Lawn and Garden Tractor Model No. 72049 – 200000001 & Up Operator’s Manual...
- Page 2 The warning system in this manual identifies potential hazards and has special safety messages that All of us at Toro want you to be completely satisfied help you and others avoid personal injury, even death. with your new product, so feel free to contact your...
-
Page 3: Table Of Contents
Contents Page Page Attachment Lift Lever ....Safety ....... . . Adjusting Dial-A-Height . -
Page 4: Safety
Safety This machine meets or exceeds the B71.1–1998 Be aware of the mower discharge direction and specifications of the American National Standards do not point it at anyone. Do not operate the Institute, in effect at the time of production. mower without either the entire grass catcher or However, improper use or maintenance by the the guard in place. -
Page 5: Slope Operation
Never carry children, even with the blades off. They may fall off and be seriously injured or Follow Toro’s recommendations for wheel interfere with safe machine operation. weight or counterweights to improve stability. -
Page 6: Toro Riding Mower Safety
The following list contains safety information Battery gases can explode. Keep cigarettes, specific to Toro products or other safety information sparks and flames away from battery. that you must know that is not included in the ANSI standards. -
Page 7: Slope Chart
Safety Slope Chart Read all safety instructions on pages 2–4. - Page 9 Safety Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. ON STEERING TOWER ON SEAT BRACKET ON FRAME STEP (Part No. 92–0301) (Part No.
-
Page 10: Gasoline And Oil
Gasoline and Oil Recommended Gasoline Use UNLEADED Regular Gasoline suitable for POTENTIAL HAZARD automotive use (85 pump octane minimum). Leaded In certain conditions gasoline is extremely regular gasoline may be used if unleaded regular is flammable and highly explosive. not available. WHAT CAN HAPPEN IMPORTANT: Never use methanol, gasoline A fire or explosion from gasoline can burn... -
Page 11: Stabilizer/Conditioner
Gasoline and Oil Stabilizer/Conditioner Filling the Fuel Tank Using a stabilizer/conditioner in the machine: Shut the engine off and set the parking brake. Keeps gasoline fresh during storage of 90 days Clean around each fuel tank cap and remove the or less. -
Page 12: Operation
Operation Think Safety First Key Choice Switch Please carefully read all the safety instructions on A turn and release switch used for deactivating the pages 2–7. Knowing this information could help you, “Operating–In–Reverse” interlock feature. Located on your family, pets or bystanders avoid injury. the seat bracket on the right hand just below the seat (Fig. -
Page 13: Releasing The Parking Brake
Operation Releasing the Parking Brake Push down on the brake pedal (Fig. 3). The parking brake lever should release. Gradually release the brake pedal. 1244a Figure 3 1. Brake pedal 2. Parking brake lever... -
Page 14: Starting And Stopping The Engine
Operation Starting and Stopping the Engine Starting Sit down on the seat. Set the parking brake; refer to Setting the Parking Brake, page 10. 1207 1206 Figure 4 Figure 5 Note: The engine will not start unless you set the parking brake or fully depress the 1. -
Page 15: Operating The Power Take Off (Pto)
Operation Operating the The Safety Interlock System Power Take Off (PTO) Understanding the Safety Interlock System The power take off (PTO) engages and disengages power to the electric clutch. The safety interlock system is designed to prevent the engine from starting unless: While the ignition key is in “RUN”... - Page 16 Operation “Key Choice” key (Fig. 9), located on the seat bracket on the right hand side just below the seat, after engaging the blade (PTO). A red light on the front POTENTIAL HAZARD console (Fig. 10) will turn on as a reminder that the operating–in–reverse interlock has been deactivated.
- Page 17 Operation Set the parking brake. Move the power take off (PTO) to “ON”. Now turn the ignition key to “START”; the engine should not crank. Push the power take off (PTO) to “OFF” and release the parking brake. Now turn the ignition key to “START”;...
-
Page 18: Indicator Control Module
Operation Indicator Control Module Hourmeter The indicator control module (Fig. 10) contains lights The hourmeter (optional on some models) records the for: number of hours the engine has operated (Fig. 10). It is turned on when the ignition switch is in the “RUN” Operating–in–Reverse or “LIGHTS”... -
Page 19: Selecting Ground Speeds
Operation IMPORTANT: Do not “Ride the Brakes” or use brakes to slow tractor movement when in gear. On hills shift to a lower gear for slower POTENTIAL HAZARD ground speed. Someone could move or attempt to operate the tractor while it is unattended. Selecting Ground Speeds WHAT CAN HAPPEN Children or bystanders may be injured if... -
Page 20: Attachment Lift Lever
Operation Attachment Lift Lever Adjusting Dial-A-Height The attachment lift lever (Fig. 12) is used to raise and The Dial-A-Height control (Fig. 12) is used to limit lower various attachments. the downward travel of the attachment. The Dial-A-Height knob is rotated to change the location of this stop, up or down. -
Page 21: Positioning The Seat
Operation Positioning the Seat Positioning the Tilt Steering Wheel The seat can move forward and backward. Position the seat where you have the best control of the The steering wheel has four tilt locations. Position the machine and are most comfortable. steering wheel where you have the best control of the machine and are most comfortable. -
Page 22: Maintenance
Maintenance Service Interval Chart Each Storage Spring Service Operation Hours Hours Hours Hours Service Service Oil—check level Oil—change* Initial Oil Filter—change* (200 hours, every other oil change or yearly) Safety System—check Brake—check Chassis—grease* Foam Air Cleaner—service* Paper Air Cleaner—replace* Spark Plug(s)—check Belts—check for wear/cracks Gasoline—drain Engine—clean outside... -
Page 23: Air Cleaner
Maintenance Air Cleaner Carefully slide the foam element off the paper element (Fig. 16). Service Interval/Specification Unscrew the cover nut and remove the cover and paper element (Fig. 16). Foam Element: Clean and re-oil after every 25 operating hours, or yearly, whichever occurs first. Cleaning the Foam and Paper Elements Paper Element: Replace after every 100 operating hours or yearly, whichever occurs first. - Page 24 Maintenance Paper Element Installing the Foam and Paper Elements A. Lightly tap the element on a flat surface to IMPORTANT: To prevent engine damage, remove dust and dirt (Fig. 18). always operate the engine with the complete foam and paper air cleaner assembly B.
-
Page 25: Engine Oil
Maintenance Engine Oil Checking Oil Level Park the machine on a level surface, disengage Service Interval/Specification the power take off (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the Change oil: engine. Remove the key. After the first 5 operating hours. - Page 26 Maintenance Changing/Draining Oil Change Oil Filter Service Interval/Specification Start the engine and let it run five minutes. This warms the oil so it drains better. Replace the oil filter every 200 hours or every other Park the machine so that the drain side is slightly oil change.
-
Page 27: Spark Plug
Maintenance Spark Plug Checking the Spark Plug Look at the center of the spark plug(s) (Fig. 23). Service Interval/Specification If you see light brown or gray on the insulator, the engine is operating properly. A black coating Check the spark plug(s) after every 200 operating on the insulator usually means the air cleaner is hours. -
Page 28: Greasing And Lubrication
Maintenance Greasing and Lubrication Lubricate the traction control pedal on hydrostatic models (or brake and clutch pedals on gear drive models) where they pivot on Service Interval/Specification mounting shaft (Fig. 25). Grease the machine after every 50 operating hours or yearly, whichever occurs first. -
Page 29: Tire Pressure
Maintenance Tire Pressure Service Interval/Specification Maintain the air pressure in the front and rear tires as specified. Check the pressure at the valve stem after every 25 operating hours or monthly, whichever occurs first (Fig. 26). Check the tires when they are cold to get the most accurate pressure reading. -
Page 30: Brake
Maintenance Brake The brake is on the right side of the rear axle, inside the rear tire (Fig. 27). If the brake does not hold securely or stopping power is insufficient, an adjustment is required. Checking the Brake Park the machine on a level surface, disengage the power take off (PTO), shift into neutral, set Figure 27 the parking brake, and turn the ignition key to... -
Page 31: Fuel Tank
Maintenance Fuel Tank Pull the fuel line off the filter (Fig. 29). Open fuel shut-off valve and allow gasoline to drain into an approved gas can. Draining The Fuel Tank Note: Now is the best time to install a new fuel filter because the fuel tank is empty. -
Page 32: Fuel Filter
Maintenance Fuel Filter Service Interval/Specification Replace the fuel filter after every 100 operating hours or yearly, whichever occurs first. Replacing the Fuel Filter Never install a dirty filter if it is removed from the fuel line. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to “OFF”... -
Page 33: Front Wheel Toe-In
Maintenance Front Wheel Toe-In Adjusting Toe-In Check the toe-in before you adjust it; refer to Service Interval/Specification Measuring Toe-In, Page 31. Maintain toe-in of the front wheels as specified. If Remove ball joint from one steering lever uneven tire wear, lawn scuffing or hard steering (Fig. -
Page 34: Fuse
Maintenance Fuse Service Interval/Specification The electrical system is protected by fuses. It requires no maintenance, however, if a fuse blows check component/circuit for malfunction or short. To replace fuses pull up on the fuse (Fig. 32) to remove or replace it. Fuse: Main/Starter F1–30 amp, blade-type Alternator F2–25 amp, blade-type... -
Page 35: Headlights
Maintenance Headlights Installing the Bulb The bulb has metal pins on the side of its base. Specification: Bulb # 1156 Automotive Type Align the pins with the slots in the bulb holder and insert the base into the holder (Fig. 34). Removing the Bulb Push and rotate the bulb clockwise until it stops. -
Page 36: Battery
Maintenance Battery Service Interval/Specification Check the electrolyte level in the battery before each use. Always keep the battery clean and fully charged. Use a paper towel to clean the battery case. If the battery terminals are corroded, clean them with a solution of four parts water and one part baking soda. -
Page 37: Adding Water To The Battery
Maintenance Adding Water to the Battery The best time to add distilled water to the battery is just before you operate the machine. This lets the water mix thoroughly with the electrolyte solution. Clean the top of the battery with a paper towel. Lift off the filler caps (Fig. - Page 38 Maintenance Charging the Battery IMPORTANT: Always keep the battery fully charged (1.260 specific gravity). This is especially important to prevent battery damage when the temperature is below 32 F (0 C). Remove the battery from the chassis; refer to Removing the Battery, page 34. Check the electrolyte level;...
-
Page 39: Wiring Diagram
Maintenance Wiring Diagram... -
Page 40: Cleaning And Storage
Maintenance Cleaning and Storage 40 F (4 C). If the temperatures will be above 40 F (4 C), check the water level in the battery and charge it every 30 days. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to Check the tire pressure;... -
Page 41: Troubleshooting
Troubleshooting PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Starter does not crank Blade control (PTO) is Move blade control (PTO) to ENGAGED. DISENGAGED. Parking brake is not on. Set parking brake. Operator is not seated. Sit on the seat. Speed selector not in “N” Move speed selector to “N”... - Page 42 Troubleshooting PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Engine loses power (continued) Dirt in fuel filter. Replace fuel filter. Dirt, water, or stale fuel is in Contact Authorized Service fuel system. Dealer. Engine overheats. Engine load is excessive. Shift into lower gear to reduce ground speed.
- Page 44 Rev. 7/21/97...