hit counter script
Table of Contents

Advertisement

QQ
3 7 63 1515 0
SERVICE MANUAL
Ver. 1.1 2005. 12
• HCD-RV222 is the tuner,
deck, CD and amplifier
section in MHC-RV222.
TE
L 13942296513
Amplifier section
The following measured at AC 120, 127, 220, 240 V
50/60 Hz
DIN power output (rated):
100 + 100 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
120 + 120 watts
(6 ohms at 1 kHz, 10% THD)
Inputs
GAME INPUT AUDIO L/R (phono jacks):
voltage 250 mV,
impedance 47 kilohms
GAME INPUT VIDEO (phono jack):
1 Vp-p, 75ohms
MIC (phone jack):
sensitivity 1 mV,
impedance 10 kilohms
www
.
Sony Corporation
9-879-926-02
2005L04-1
Home Audio Division
© 2005. 12
Published by Sony Engineering Corporation
http://www.xiaoyu163.com
x
ao
u163
y
i
http://www.xiaoyu163.com
HCD-RV222
2 9
8
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Base Unit Name
Optical Pick-up Name
Q Q
Model Name Using Similar Machanism
3
6 7
1 3
1 5
TAPE
Section
Tape Mechanism Type
SPECIFICATIONS
Outputs
PHONES (stereo phone jack):
VIDEO OUT (phono jack):
SPEAKER:
CD player section
System
Laser
Frequency response
Signal-to-noise-ratio
Dynamic range
Video color system format
MINI Hi-Fi COMPONENT SYSTEM
co
.
9 4
2 8
E Model
HCD-RV22
CDM74-K4BD49
CDM74KS-KBD49
BU-K4BD49
KSM-213DHAP
HCD-RV22
0 5
8
2 9
9 4
2 8
CWM43FF13
CWM43FF25
accepts headphones of
8 ohms or more
max. output level 1 Vp-p,
unbalanced, Sync negative
load impedance 75 ohms
accepts impedance of 6 to
16 ohms
Compact disc and digital
audio system
Semiconductor laser
(λ=770 – 810 nm)
Emission duration:
continuous
2 Hz – 20 kHz (±0.5 dB)
More than 90 dB
More than 90 dB
NTSC, PAL
– Continued on next page –
m
9 9
9 9
1

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-RV222

  • Page 1 HCD-RV222 3 7 63 1515 0 SERVICE MANUAL E Model Ver. 1.1 2005. 12 • HCD-RV222 is the tuner, deck, CD and amplifier section in MHC-RV222. Model Name Using Similar Mechanism HCD-RV22 CDM74-K4BD49 CD Mechanism Type CDM74KS-KBD49 Section Base Unit Name...
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3 HCD-RV222 3 7 63 1515 0 Notes on Chip Component Replacement NOTES ON LASER DIODE EMISSION CHECK • Never reuse a disconnected chip component. The laser beam on this model is concentrated so as to be focused on • Notice that the minus side of a tantalum capacitor may be the disc reflective surface by the objective lens in the optical pick- damaged by heat.
  • Page 4 HCD-RV222 Ver. 1.1 3 7 63 1515 0 MODEL IDENTIFICATION PLAYABLE DISC You can playback the following discs on this system. The other – BACK PANEL – discs cannot be played back. Part No. List of playable discs Format of discs...
  • Page 5: Table Of Contents

    HCD-RV222 3 7 63 1515 0 TABLE OF CONTENTS 1. SERVICE NOTE 6-5. Circuit Boards Location ............ 29 6-6. Printed Wiring Board –CD Mechanism Section (1/2)– ..32 1-1. Service Position of CD Mechanism Deck ......6 6-7. Schematic Diagram –CD Mechanism Section (1/2)– ..33 1-2.
  • Page 6: Service Note

    HCD-RV222 SECTION 1 SERVICE NOTE 3 7 63 1515 0 1-1. SERVICE POSITION OF CD MECHANISM DECK Remove the CD mechanism deck and place it on top of the pedestal as shown. Inspect the BD49 board in this set up.
  • Page 7: General

    HCD-RV222 SECTION 2 GENERAL 3 7 63 1515 0 This section is extracted from instruction manual. L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 8 HCD-RV222 3 7 63 1515 0 L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 9: Disassembly

    HCD-RV222 SECTION 3 DISASSEMBLY 3 7 63 1515 0 Note : Disassemble the unit in the order as shown below. 3-1. CASE (TOP) (Page 10) 3-2. CD DOOR (Page 10) 3-3. FRONT PANEL SECTION (Page 11) 3-4. CD MECHANISM DECK 3-5.
  • Page 10: Case (Top)

    HCD-RV222 3 7 63 1515 0 Note : Follow the disassembly procedure in the numerical order given. 3-1. CASE (TOP) qd two screws (+BVTP 3 × 10) qh case (top) 7 two screws (case 3 TP2) qs case (side-L) 9 screw (+BVTP 3 ×...
  • Page 11: Front Panel Section

    HCD-RV222 3 7 63 1515 0 3-3. FRONT PANEL SECTION qf screw (+BV (3 − CR)) 4 screw (+BVTP 3 × 8) qa CN304 (8P) qg CN301 (3P) 1 CN805 (2P) 3 wier (flat type) (11 core) (CN882) 8 screw (+BVTP 3 ×...
  • Page 12: Tape Mechanism Deck, Mic Board

    HCD-RV222 3 7 63 1515 0 3-5. TAPE MECHANISM DECK, MIC BOARD 4 two MIC knobs 3 tape mechanism deck 2 six screws 1 wier (flat type) (13 core) (+BVTP 2.6 × 8) jack bracket 5 two screws 7 MIC board (+BVTP 2.6 ×...
  • Page 13: Back Panel Section, Sub Trans Board

    HCD-RV222 3 7 63 1515 0 3-7. BACK PANEL SECTION, SUB TRANS BOARD qa back panel section 0 SUB TRANS board 3 CN901 (2P) 7 two screws 9 two screws (+BVTP 3 × 10) (+BVTP 3 × 10) 2 CN906 (3P)
  • Page 14: Main Board

    HCD-RV222 3 7 63 1515 0 3-9. MAIN BOARD 6 MAIN board 3 CN907 (10P) 1 screw (+BV (3 − CR)) 2 earth wire MAIN board 5 CN441 4 two screws (+BVTP 3 × 8) L 13942296513 3-10. AMP BOARD...
  • Page 15: Bd49 Board

    HCD-RV222 3 7 63 1515 0 3-11. BD49 BOARD 3 screw 1 wier (flat type) (29 core) (+BVTP 2.6 × 8 ) (CN101) 4 gap tube 6 BD49 board 5 Remove the four solders. 2 wier (flat type) (16 core) (CN102) L 13942296513 3-12.
  • Page 16: Driver Board, Sw Board

    HCD-RV222 3 7 63 1515 0 3-13. DRIVER BOARD, SW BOARD 1 two screws (+BTTP (M2.6)) 3 CN703 (4P) 4 DRIVER board 5 screw (+BTTP (M2.6)) 6 SW board 2 wier (flat type) (5 core) (CN702) L 13942296513 3-14. OPTICAL PICK-UP...
  • Page 17: Sensor Board

    HCD-RV222 3 7 63 1515 0 3-15. SENSOR BOARD 1 floating screw (+PTPWH M2.6) 2 t ray 8 s crew (+BTTP (M2.6)) 3 b elt (table) 0 SENSOR board 4 floating screw (+PTPWH M2.6) 5 p ulley (table) 6 floating screw 9 CN731 (3P) (+PTPWH M2.6)
  • Page 18: Motor (Ld) Board

    HCD-RV222 3 7 63 1515 0 3-17. MOTOR (LD) BOARD 2 two screws (+BTTP (M2.6)) 4 Remove the two solders. 3 MOTOR (LD) board 5 l oading motor assy (M751) 1 b elt (loading) L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 19: Test Mode

    HCD-RV222 SECTION 4 TEST MODE 3 7 63 1515 0 MC COLD RESET CD TRAY LOCK MODE The cold reset clears all data including preset data stored in the This mode is used to unable to take sample disc out of tray in the RAM to initial conditions.
  • Page 20 HCD-RV222 3 7 63 1515 0 AGING MODE 3. Tape Deck Section The sequence during the aging mode is following as below. This mode can be used for operation check of CD section and tape If an error occurred, stop display that step.
  • Page 21 HCD-RV222 3 7 63 1515 0 MC TEST MODE 1. Mechanism Deck Error Code Mode When this mode is entered, mechanism deck error code is displayed This mode is used to check operations of microprocessor. with the 10-character format on the fluorescent indicator tube.
  • Page 22 HCD-RV222 3 7 63 1515 0 The 7th and 8th digit from the left indicates: The 5th and 6th digit from the left indicates: (Motor status display) (Error step display) The 7th and 8th digit from the left indicates which motor output The 5th and 6th digit from the left indicates which processing when status when an error occurred is indicated.
  • Page 23: Electrical Adjustments

    HCD-RV222 SECTION 5 ELECTRICAL ADJUSTMENTS 3 7 63 1515 0 Note: Clear RF signal waveform means that the shape “ ◊ ” can be clearly CD SECTION distinguished at the center of the waveform. Note: RF signal waveform 1. CD Block is basically designed to operate without adjustment.
  • Page 24 HCD-RV222 3 7 63 1515 0 VIDEO SECTION AUDIO LEVEL, VIDEO CLOCK, AUDIO SERVO – VMP43GY BOARD (Component Side) – CLOCK CHECK level meter VMP43GY board TP415 (L-OUT) TP413 (R-OUT) – TP70 frequency counter VMP43GY board (54 MHz) TP70 (54 MHz) TP182 (4.2336 MHz)
  • Page 25: Diagrams

    HCD-RV222 SECTION 6 DIAGRAMS 3 7 6 3 1 5 1 5 0 6-1. BLOCK DIAGRAM — CD SERVO SECTION — FREQUENCY • SIGNAL PATH SELECT SWITCH Q102 : CD PLAY FILTER RF AMP, FOCUS/TRACKING ERROR AMP IC103 170 171...
  • Page 26: Block Diagram -Audio/Video Cd Section

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-2. BLOCK DIAGRAM — AUDIO/VIDEO CD SECTION — +3.3V REGULATOR CD +5V Q581 FROM IC505 (1/2) AUDDTO0 MAIN DATA VOUTL CD L CD SERVO LOW-PASS SECTION SECTION AUDBCK FILER...
  • Page 27: Block Diagram -Main Section

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-3. BLOCK DIAGRAM — MAIN SECTION — AUDIO/VIDEO CD SECTION (Page 26) JK441 JK805 (2/2) –1 HCD-RV22 59 GAME L LINE AMP TONE OUT1 36 VIN1 VOL OUT1 GAIN INPUT...
  • Page 28: Block Diagram -Panel/Power Supply Section

    HCD-RV222 Ver. 1.1 3 7 6 3 1 5 1 5 0 6-4. BLOCK DIAGRAM — PANEL/POWER SUPPLY SECTION — MAIN POWER TRANSFORMER PT901 F904, F905 AMP B+ 1 RECT AC-1 +4.5V D401 AMP B– 1 REGULATOR CD +4.5V Q201 +2.5V...
  • Page 29: Circuit Boards Location

    HCD-RV222 3 7 63 1515 0 6-5. CIRCUIT BOARDS LOCATION VMP43GY board SENSOR board BD49 board SW board MOTOR (TB) board MOTOR (LD) board DRIVER board VCD CONNECT board TRANS board AMP board L 13942296513 VIDEO OUT board SUB TRANS board...
  • Page 30 HCD-RV222 Ver. 1.1 3 7 63 1515 0 • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF) •...
  • Page 31 HCD-RV222 3 7 6 3 1 5 1 5 0 • Waveforms – BD49 Board – – VMP43GY Board – – PANEL Board – IC103 qg (RFAC) IC504 1 (BCK), IC505 os (L CDBCK), IC505 <zmc (RFAC) IC601 qd (I-XT2) (CD Play Mode) IC505 <x/c (AUDBCK)
  • Page 32: Printed Wiring Board -Cd Mechanism Section (1/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-6. PRINTED WIRING BOARD — CD MECHANISM SECTION (1/2) — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. 1 3 9 4 2 2 9 6 5 1 3 (Page 37) •...
  • Page 33: Schematic Diagram -Cd Mechanism Section (1/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 • Refer to page 31 for Waveforms. 6-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 51 for IC Block Diagrams. TP11 C121 TP18 FB111...
  • Page 34: Printed Wiring Boards -Cd Mechanism Section (2/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-8. PRINTED WIRING BOARDS — CD MECHANISM SECTION (2/2) — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. 1 3 9 4 2 2 9 6 5 1 3...
  • Page 35: Schematic Diagram -Cd Mechanism Section (2/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-9. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 51 for IC Block Diagrams. IC701 IC B/D R702 R701 D701 C715 CN704 C751 CN721 M751...
  • Page 36: Printed Wiring Board -Vcd Connect Section

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-10. PRINTED WIRING BOARD — VCD CONNECT SECTION — 6-11. SCHEMATIC DIAGRAM — VCD CONNECT SECTION — • Refer to page 29 for Circuit Boards Location. • : Uses unleaded solder.
  • Page 37: Printed Wiring Board -Vmp Section

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-12. PRINTED WIRING BOARD — VMP SECTION — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. (Page 36) • Semiconductor Location Ref. No. Location...
  • Page 38: Schematic Diagram -Vmp Section (1/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 • Refer to page 31 for Waveforms. 6-13. SCHEMATIC DIAGRAM — VMP SECTION (1/2) — • Refer to page 52 for IC Block Diagrams. R152 C155 R158 C154 TP419...
  • Page 39: Schematic Diagram -Vmp Section (2/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 • Refer to page 31 for Waveforms. 6-14. SCHEMATIC DIAGRAM — VMP SECTION (2/2) — • Refer to page 54 for IC Pin Description of IC505. FL503 FL504 FB501...
  • Page 40: Schematic Diagram -Main Section (1/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-15. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 53 for IC Block Diagrams. CN309 Q372 R391 R386 R219 R385 (Page 47) R216 R217 R399 R388...
  • Page 41: Schematic Diagram -Main Section (2/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 • Refer to page 53 for IC Block Diagrams. 6-16. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 59 for IC Pin Description of IC371. (Page 40)
  • Page 42: Printed Wiring Board -Main Section

    HCD-RV222 Ver. 1.1 3 7 6 3 1 5 1 5 0 6-17. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. (Page 34) (Page 36) (Page 46) •...
  • Page 43: Printed Wiring Boards -Panel Section

    HCD-RV222 Ver. 1.1 3 7 6 3 1 5 1 5 0 6-18. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. IC610 (Page 36) 1 3 9 4 2 2 9 6 5 1 3...
  • Page 44: Schematic Diagram -Panel Section (1/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-19. SCHEMATIC DIAGRAM — PANEL SECTION (1/2) — CN605 R704 R706 R708 R700 JW660 JW659 R702 (Page 47) Q610 Q612 Q611 Q614 Q615 Q613 R698 CN604 JW674 JW718 (Page 47)
  • Page 45: Schematic Diagram -Panel Section (2/2)

    HCD-RV222 Ver. 1.1 3 7 6 3 1 5 1 5 0 • Refer to page 31 for Waveforms. 6-20. SCHEMATIC DIAGRAM — PANEL SECTION (2/2) — • Refer to page 60 for IC Pin Description of IC601. FL601...
  • Page 46: Printed Wiring Boards -Jack Section

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-21. PRINTED WIRING BOARDS — JACK SECTION — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. (Page 42) (Page 43) (Page 42) (Page 43)
  • Page 47: Schematic Diagram -Jack Section

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-22. SCHEMATIC DIAGRAM — JACK SECTION — S660 C830 C831 SW601 CN804 J801 (Page 40) R673 C832 W803 CN606 CN607 (Page 44) (Page 44) C833 IC803 CN808 JK802 C859...
  • Page 48: Printed Wiring Board -Power Section (1/2)

    HCD-RV222 3 7 6 3 1 5 1 5 0 6-23. PRINTED WIRING BOARD — POWER SECTION (1/2) — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. 1 3 9 4 2 2 9 6 5 1 3 •...
  • Page 49: Printed Wiring Boards -Power Section (2/2)

    HCD-RV222 Ver. 1.1 3 7 6 3 1 5 1 5 0 6-24. PRINTED WIRING BOARDS — POWER SECTION (2/2) — • Refer to page 29 for Circuit Boards Location. : Uses unleaded solder. (Page 48) 1 3 9 4 2 2 9 6 5 1 3 (Page 42) •...
  • Page 50: Schematic Diagram -Power Section

    HCD-RV222 Ver. 1.1 3 7 6 3 1 5 1 5 0 6-25. SCHEMATIC DIAGRAM — POWER SECTION — JW403 L441 R451 RY441 C441 R441 R461 JW441 IC441(1/2) C445 R413 R462 R466 R465 R411 L442 R447 D443 EP491 Q483...
  • Page 51 HCD-RV222 3 7 63 1515 0 • IC BLOCK DIAGRAMS IC103 CXA2581N-T4 (BD49 BOARD) RW/ROM DC OFST RFDCI – – RFDCO – RW/ROM VOFST APC AMP EQ ON/OFF RFAC EQ IN RW/ROM RFAC AC SUM SUMMING VOFST – –...
  • Page 52 HCD-RV222 3 7 63 1515 0 IC504 PCM1748E/2K (VMP43GY BOARD) 15 14 ZERO DETECT SYSTEM FUNCTION CLOCK OUTPUT AMP AND CONTROL MANAGER CONVERTER LOW-PASS FILTER INTERFACE 8 TIME OVER SAMPLING ENHANCED DIGITAL FILTER MULTI-LEVEL WITH SYSTEM DELTA-SIGMA FUNCTION CLOCK...
  • Page 53 HCD-RV222 3 7 63 1515 0 IC101 BD3401KS2 (MAIN BOARD) VOLOUT2 TNF2 BASS MIDDLE TREBLE TNF1 BBNF2 SUR1 BBIN2 BASS MIDDLE TREBLE SURROUND SUR2 fc=100HZ LINEOUT2 LINEOUT1 BUFFER MIC MIX SAOUT2 VOCAL FADER SWOUT SAOUT1 FILTER 1/2 Vcc GAME L...
  • Page 54 HCD-RV222 3 7 63 1515 0 • IC Pin Function Description • IC505 CXD1887R (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, MPEG VIDEO/AUDIO DECODER, VIDEO SIGNAL ENCODER) (VMP43GY BOARD (2/2)) Pin No. Pin Name Pin Description Connected to ground via a capacitor.
  • Page 55 HCD-RV222 3 7 63 1515 0 Pin No. Pin Name Pin Description IVS4 — Ground pin (for I/O) DRCAS Column address strobe signal output to the D-RAM LVD4 — Digital power supply pin (+2.5 V) (for AV decoder block)
  • Page 56 HCD-RV222 3 7 63 1515 0 Pin No. Pin Name Pin Description L SENS SENS signal input SENS SENS signal output L SLCK SENS serial data readout clock signal output SCLK SENS serial data readout clock signal input VDD3 —...
  • Page 57 HCD-RV222 3 7 63 1515 0 Pin No. Pin Name Pin Description AVS0 — Analog ground pin ADIO Output for the test Not used. RFDC RF signal input from the RF amplifier Center servo analog signal input Tracking error signal input from the RF amplifier...
  • Page 58 HCD-RV222 3 7 63 1515 0 Pin No. Pin Name Pin Description AUDDTO1 Serial audio data output Not used. (Open) AUDBCK Serial audio bit clock signal (2.8224 MHz) output to the digital filter AUDLRCK Serial audio L/R sampling clock signal (44.1 kHz) output to the digital filter...
  • Page 59 HCD-RV222 3 7 63 1515 0 • IC371 BU2099FV (SP DRIVER) (MAIN BOARD (2/2)) Pin No. Pin Name Pin Description — Ground pin N.C. — Not used. (Open) DATA Serial data input from the motor/plunger driver CLOCK Serial data transfer clock signal input from the system controller...
  • Page 60 HCD-RV222 3 7 63 1515 0 • IC601 LC876964C-52S6-E (SYSTEM CONTROLLER) (PANEL BOARD (2/2)) Pin No. Pin Name Pin Description O-MP3 CS CS signal output to CD digital processor O-MP3 LP LP signal output to CD digital processor and motor signal output...
  • Page 61 HCD-RV222 3 7 63 1515 0 Pin No. Pin Name Pin Description STREAM-LED4 Illumination LED control signal output STREAM-LED3 Illumination LED control signal output STREAM-LED2 Illumination LED control signal output STREAM-LED1 Illumination LED control signal output I-LC72121 DI Data signal input from tuner...
  • Page 62: Exploded Views

    7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3 u163 4-253-803-71 DOOR, CD (EXCEPT TH) 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3 4-244-849-71 CASE (TOP) 7-685-871-01 SCREW +BVTT 3X6 (S) 1-769-940-11 WIRE (FLAT TYPE) (11 CORE) 3-038-018-01 EMBLEM, SONY (EXCEPT TH) 4-998-417-02 EMBLEM (NO.5), SONY (TH) http://www.xiaoyu163.com...
  • Page 63: Front Panel Section (1)

    HCD-RV222 Ver. 1.1 3 7 63 1515 0 7-2. FRONT PANEL SECTION (1) not supplied (REM board) FL601 supplied L 13942296513 supplied not supplied not supplied not supplied (H/P JACK board) Ref. No. Part No. Description Remark Ref. No.
  • Page 64: Front Panel Section (2)

    HCD-RV222 3 7 63 1515 0 7-3. FRONT PANEL SECTION (2) not supplied not supplied L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-231-841-01 SPRING (HEART CAM-B) 4-231-824-01 CAM (A), HEART 4-231-825-01 CAM (B), HEART...
  • Page 65: Front Panel Section (3)

    HCD-RV222 3 7 63 1515 0 7-4. FRONT PANEL SECTION (3) not supplied not supplied not supplied supplied not supplied (6 STREAM LED board) not supplied not supplied L 13942296513 not supplied not supplied not supplied Ref. No. Part No.
  • Page 66: Main Board Section

    HCD-RV222 Ver. 1.1 3 7 63 1515 0 7-5. MAIN BOARD SECTION not supplied PT901 not supplied (TRANS board) not supplied FC901 F905 F906 F907 F904 L 13942296513 not supplied not supplied Ref. No. Part No. Description Remark Ref. No.
  • Page 67: Cd Mechanism Deck Section (1)

    HCD-RV222 Ver. 1.1 3 7 63 1515 0 7-6. CD MECHANISM DECK SECTION (1) (CDM74-K4BD49: TH) (CDM74KS-K4BD49: EXCEPT TH) M741 L 13942296513 CD mechanism deck section -2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark...
  • Page 68: Cd Mechanism Deck Section (2)

    HCD-RV222 Ver. 1.1 3 7 63 1515 0 7-7. CD MECHANISM DECK SECTION (2) (CDM74-K4BD49: TH) (CDM74KS-K4BD49: EXCEPT TH) RE701 M751 CD mechanism deck section -3 L 13942296513 not supplied (VCD CONNECT board) Ref. No. Part No. Description Remark Ref.
  • Page 69: Cd Mechanism Deck Section (3)

    HCD-RV222 Ver. 1.1 3 7 63 1515 0 7-8. CD MECHANISM DECK SECTION (3) (CDM74-K4BD49: TH) (CDM74KS-K4BD49: EXCEPT TH) L 13942296513 BU-K4BD49 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-2102-809-1 PULLEY (KH) ASSY (EXCEPT TH)
  • Page 70: Base Unit Section

    HCD-RV222 3 7 63 1515 0 7-9. BASE UNIT SECTION (BU-K4BD49) not supplied L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-4750-371-A BD49 BOARD, COMPLETE 1-782-817-11 WIRE (FLAT TYPE) (16 CORE) 0 402 8-820-122-01 OPTICAL PICK-UP (KSM213DHAP/Z-NP) 3-087-053-01 +BVTP 2.6 (3CR)
  • Page 71: Electrical Parts List

    HCD-RV222 Ver. 1.1 SECTION 8 ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 72 HCD-RV222 Ver. 1.1 BD49 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R441 1-249-417-11 CARBON 1/4W C112 1-126-209-11 ELECT CHIP 100uF R442 1-249-417-11 CARBON 1/4W C113 1-128-995-21 ELECT CHIP 100uF...
  • Page 73 HCD-RV222 Ver. 1.1 BD49 DRIVER H/P JACK MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R151 1-216-833-11 METAL CHIP 1/10W H/P JACK BOARD R152 1-216-837-11 METAL CHIP 1/10W **************...
  • Page 74 HCD-RV222 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C145 1-126-964-11 ELECT 10uF C259 1-126-957-11 ELECT 0.22uF C146 1-136-165-00 FILM 0.1uF C264 1-162-971-11 CERAMIC CHIP 0.001uF C147 1-126-964-11 ELECT...
  • Page 75 HCD-RV222 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D309 6-500-522-31 DIODE 10EDB40-TB5 Q322 6-550-580-01 TRANSISTOR 2SA1235TP-1F D310 6-500-522-31 DIODE 10EDB40-TB5 Q323 8-729-120-28 TRANSISTOR 2SC1623-L5L6 D311 6-500-522-31 DIODE 10EDB40-TB5...
  • Page 76 HCD-RV222 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R164 1-216-821-11 METAL CHIP 1/10W R250 1-216-833-11 METAL CHIP 1/10W R165 1-216-833-11 METAL CHIP 1/10W R251 1-216-833-11 METAL CHIP 1/10W...
  • Page 77 HCD-RV222 Ver. 1.1 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R374 1-216-833-11 METAL CHIP 1/10W C842 1-162-969-11 CERAMIC CHIP 0.0068uF 10% R375 1-216-833-11 METAL CHIP 1/10W C843 1-115-416-11 CERAMIC CHIP 0.001uF...
  • Page 78 HCD-RV222 Ver. 1.1 MOTOR (LD) MOTOR (TB) PANEL 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R820 1-216-837-11 METAL CHIP 1/10W C620 1-119-772-11 ELECT 47uF R821 1-216-833-11 METAL CHIP 1/10W...
  • Page 79 HCD-RV222 Ver. 1.1 PANEL 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D609 8-719-988-61 DIODE 1SS355TE-17 R605 1-216-829-11 METAL CHIP 4.7K 1/10W D610 8-719-056-78 DIODE UDZ-TE-17-4.3B R606 1-216-829-11 METAL CHIP 4.7K...
  • Page 80 HCD-RV222 Ver. 1.1 PANEL 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R670 1-216-827-11 METAL CHIP 3.3K 1/10W R743 1-216-845-11 METAL CHIP 100K 1/10W R671 1-216-829-11 METAL CHIP 4.7K 1/10W...
  • Page 81 HCD-RV222 Ver. 1.1 PANEL SENSOR SUB TRANS TRANS 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S605 1-762-875-21 SWITCH, KEYBOARD (DISC 2) SUB TRANS BOARD S606 1-762-875-21 SWITCH, KEYBOARD (DISC 3)
  • Page 82 HCD-RV222 Ver. 1.1 TRANS VCD CONNECT VIDEO OUT VMP43GY 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > C203 1-126-206-11 ELECT CHIP 100uF 6.3V C204 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 83 HCD-RV222 Ver. 1.1 VMP43GY 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C548 1-164-156-11 CERAMIC CHIP 0.1uF < COIL > C549 1-162-913-11 CERAMIC CHIP 0.5PF C550 1-162-913-11 CERAMIC CHIP 0.5PF...
  • Page 84 HCD-RV222 Ver. 1.1 VMP43GY 6 STREAM LED 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R551 1-218-852-11 METAL CHIP 1.6K 0.5% 1/10W MISCELLANEOUS R552 1-216-820-11 METAL CHIP 1/10W *************** R554...
  • Page 85 HCD-RV222 3 7 63 1515 0 MEMO L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 86 HCD-RV222 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.

Table of Contents

Save PDF