Table of Contents
Advertisement
Quick Links
Hardware Quick Start Guide
Q-SYS™ PTZ-IP Cameras
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
Maintenance and Repair
WARNING!: Advanced technology, e.g., the use of modern materials and powerful electronics, requires specially adapted
maintenance and repair methods. To avoid a danger of subsequent damage to the apparatus, injuries to persons and/or the
creation of additional safety hazards, all maintenance or repair work on the apparatus should be performed only by a QSC
authorized service station or an authorized QSC International Distributor. QSC is not responsible for any injury, harm or
related damages arising from any failure of the customer, owner or user of the apparatus to facilitate those repairs.
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
RoHS STATEMENT
The QSC Q-SYS PTZ-IP Cameras PTZ-12x72 and PTZ-20x60 are in compliance with European Directive 2011/65/EU – Restriction of
Hazardous Substances (RoHS2).
The QSC Q-SYS PTZ-IP Cameras PTZ-12x72 and PTZ-20x60 are in compliance with "China RoHS" directives. The following chart is
provided for product use in China and its territories:
Packing List
Camera PTZ-12x72 or PTZ-20x60
Quick Start Guide TD-000541-00
Safety document
Wall Bracket
Fastener Kit (fi ve M3*6 screws, and one 1/4 20 screw)
CAUTION!: Do not carry the camera by the lens assembly, do not turn the lens assembly by hand. Mechanical damage
may occur.
TD-000541-01-B
*TD-000541-01*
™
IMPORTANT SAFETY INSTRUCTIONS
5. Install in accordance with the
manufacturer's instructions.
6. Only use attachments/accessories
specifi ed by the manufacturer.
Item
7. Refer all servicing to qualifi ed service
8. Adhere to all applicable, local codes.
9. Use only a Class 2 / LPS Power Supply.
Quantity
1
1
1
1
1
personnel.
®
Advertisement
Table of Contents
Related Manuals for QSC Q-SYS
Summary of Contents for QSC Q-SYS
-
Page 1: Important Safety Instructions
To avoid a danger of subsequent damage to the apparatus, injuries to persons and/or the creation of additional safety hazards, all maintenance or repair work on the apparatus should be performed only by a QSC authorized service station or an authorized QSC International Distributor. QSC is not responsible for any injury, harm or related damages arising from any failure of the customer, owner or user of the apparatus to facilitate those repairs. -
Page 2: Connections And Controls
5 seconds. This resets all parameters to the factory defaults. 4. Kensington™ Lock slot – Security cable not supplied. 5. LAN / POE – Q-SYS Gigabit Ethernet port / CAT5e or better / RJ45 / connect to the Q-LAN™ network switch with Power over Ethernet 6. -
Page 3: Installation
Installation (x4) Install the Wall Mount Bracket (x4) Refer to Figure 3 1. Select location on the wall or other vertical surface where the camera is to be mounted. Make sure the surface is strong enough to hold the weight of the camera and bracket. -
Page 4: Specifications
Pan / Tilt Angle and Speed Pan: ±170° rotation, speed: 1.7° to 100°/sec, Tilt: -30° to +90° rotation, speed: 1.7° to 69.9°/s Ceiling Mountable Image rotation for ceiling mounting set in Q-SYS Designer. Ceiling mount bracket accessory available. HD Video Outputs HDMI v1.3 and 3G-SDI... - Page 5 FAX: +1 (714) 754-6173 © 2016 – 2017 QSC, LLC. All rights reserved. QSC, the QSC logo, Q-SYS, and the Q-SYS logo are registered trademarks of QSC, LLC in the U.S. Patent and Trademark Offi ce and other countries. Q-LAN is a trademark of QSC, LLC. Patents may apply or be pending. All other trademarks are the property of their respective owners.