Sharp MX-M904 Installation Manual
Digital multifunctional
system
Hide thumbs
Also See for MX-M904:
- Technical handy manual (77 pages) ,
- Brochure & specs (12 pages) ,
- Manual (16 pages)
Advertisement
Quick Links
Download this manual
See also:
Manual
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
INSTALLATION MANUAL
DIGITAL MULTIFUNCTIONAL
SYSTEM
MODEL
SHARP CORPORATION
MX-M904
MX-M1054
MX-M1204
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
Advertisement
Related Manuals for Sharp MX-M904
Summary of Contents for Sharp MX-M904
-
Page 1: Sharp Corporation
INSTALLATION MANUAL DIGITAL MULTIFUNCTIONAL SYSTEM MX-M904 MX-M1054 MX-M1204 MODEL Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. -
Page 2: Note For Servicing
If toner or developer contact the eyes, wash eyes immediately and contact a doctor if necessary. The interior of the machine has sharp edges. Be careful when servicing the machine, to avoid contact with these edges. - Page 3 The organic photoconductor (OPC) drum used in the machine may undergo qualitative change due to organic gases such as ammonium. Installation of this machine near a diazo-type copier may result in copy quality problems. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 2...
- Page 4 208V lamp (RLMPU0764FCPZ). (Measurement method) Voltage reference points for wall outlet. Cut the four corners of the bottom case. Measure the voltage between L and N of the figure above using a digital multi meter. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 3...
- Page 5 Cut the part of the bottom case that overlaps with slope. Remove the vinyl bag from the main unit. Carefully roll the main unit down the ramps in the direction of the arrow. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 4...
- Page 6 NOTE: When moving the machine again after unpacking, be sure to attach the protection material. (If not, the OPC drum may be damaged.) Open the front cover. Pull out the intermediate frame. Remove the protection sheet and the Operation Manual. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 5...
- Page 7 Remove the scanner lock screw (a) and the caution label (b). Name Quantity Operation panel Panel cover B Panel cover below Screw 3 x 6 Screw 4 x 8 Clamp Panel support plate unit Panel cover A Height adjuster plate Lower cover MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 6...
- Page 8 Attach the document scan section label to the top of the DSPF the wires. unit. NOTE: When wiring the harness, be sure to check that the cable is not in the hole. Remove slack from the har- ness. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 7...
- Page 9 NOTE: Be careful not to pinch the lead wires. Attach the panel cover A (Packed items No.8) with the screw. (Packed items No.4 x2). NOTE: At that time, pass the harness through the hole in the cover. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 8...
- Page 10 Attach the operation Panel cover B (Packed items No.2) with the screw. (Packed items No.4 x2). And, attach the lower cover (Packed items No.10) with the screw. (Packed items No.4). 11) Attach the operation panel upper cover with the screw. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 9...
- Page 11 Slide the developing unit (a) to the right, and pull it out until the grip (b) can be held. NOTE: If the machine is left unused for one month or more, the heat roller rubber may be deformed. In such a case, release the pressure. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 10...
- Page 12 Remove the connector (a), the screw (b), and the cover (c). * Be careful not to smear the pin of the connector (a) with toner. 10) Attach the cover (a). 11) Attach the guide (a), and secure it with the screw (b). MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 11...
- Page 13 OFF. 16) Attach the cover (a), and secure it with the screw (b). 17) Insert the toner tray (a), and close the front cover (b). MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 12...
- Page 14 [EXECUTE] key returns to the normal display, showing completion of the setting operation. I. Toner cartridge installation Pull out the toner tray (a). Check to confirm that toner collection container (a) is securely installed. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 13...
- Page 15 Select "recycled" on the selection box of the "Type". Select "A4" on the selection box of the "Size". Touch the [Submit] key. (2) Tray size setup a. Inch series tray 1, tray 2 (LT to A4) Pull out the tray 1/2 (a). MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 14...
- Page 16 (A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.) the desired size, press the lock button (c). * If slid to a standard paper size, guide plate (b) will lock auto- matically. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 15...
- Page 17 The copy density and gradation adjustment is performed auto- matically, and the adjustment pattern is printed. If there is any streak or unclear print on the printed check pat- tern, check the print engine for any problems. High density density MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 16...
- Page 18 (ADJ11C (2)). Also when the service target is selected in procedure 4) to exe- cute the automatic adjustment and a satisfactory result is not obtained, perform the manual gray balance adjustment (ADJ 11C (2)). MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 17...
- Page 19 • Use the "packing material for fixing the separation pawls" which was removed when unpacking. NOTE: Since the hard disk drive is built in the machine, refrain from vibrations or shocks to the machine when in transit. MX-M1204 MX-M904/M1054/M1204 (MAIN UNIT) 2 – 18...