Page 1
PCV-RX6 __ Series SERVICE MANUAL For American Area US Model Ver. 4-2002F Canadian Model Revision History Lineup: PCV-RX640 PCV-RX671 PCV-RX650 PCV-RX672 S400 PCV-RX660 PCV-RX681 PCV-RX670 PCV-RX682 PCV-RX680G PCV-RX651 PCV-RX690G PCV-RX641 PCV-RX600E PCV-RX600N Specifications Model-name PCV-RX690G PCV-RX680G PCV-RX670 PCV-RX660 PCV-RX650 PCV-RX681 PCV-RX682 P4 2.2GHz...
Page 2
Information in this document is subject to change without notice. CAUTION Danger of explosion if battery is incorrectly replaced. Sony, VAIO and CLIE are trademarks or registered trademarks of Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf Replace only with the same or equivalent type and other Microsoft products are trademarks or registered trademarks recommended by the manufacturer.
TABLE OF CONTENTS OPERATION PROGRAMS FOR SERVICE ............3-1. General ..............DISASSEMBLY 3-2. PC-Doctor Starting Method ........3-3. intel815E-B Video Diag Starting Method ....2-1. Flow Chart ..............2-2. Top Panel Section ............ SERVICE INFORMATION 2-3. Left Panel Section ............ 2-4.
2-2. TOP PANEL SECTION 2 Remove the top panel section in the direction of arrow A . 1 two claws 2-3. LEFT PANEL SECTION 1 Pull thelever. 2 Remove the left panel section in the direction of arrow A . Confidential PCV-RX6__Series (AM)
2-4. DVD-ROM, DVD-RW, CD-RW, CD-ROM 2 harness (IDE CD/DVD) 1 power connector 5 Remove the CD holder ass’y in the direction of arrow A . 4 harness (IDE CD/DVD) 7 DVD-ROM DVD-RW 3 power connector 9 Remove the drive adaptor in the direction of arrow C .
2-5. SWITCHING POWER (1-468-417-72) 2 Push the lever. 3 bracket power supply ass’y 5 three screws (No.6-32UNC) 1 screw (No.6-32UNC) 4 Disconnect respective power connectors on the 6 switching power mother board, DVD-ROM, CD-RW, FDD and HDD. (1-468-601-14) 2 Push the lever 3 bracket power supply ass’y 5 three screws (No.6-32UNC)
2-12. PANEL ASS’Y (LOWER) (U) 3 two claws 4 Remove the front panel ass’y (lower) (U) in the direction of arrow A . 2 two claws 1 two claws 2-13. RIGHT PANEL 2 Remove the right panel in the direction of arrow A . 1 two claws Confidential PCV-RX6__Series (AM)
2-14. CNX-138 BOARD 4 two screws (SW) (No.6-32UNC) 2 harness (USB/LU) 1 harness 5 CNX-138 board (1394) 3 Remove the bracket AV ass’y in the direction of arrow A . 2-15. CNX-137 BOARD 5 three screws (SW) (No.6-32UNC) 3 harness (USB/LU) 2 harness (1394)
2-16. SWX-66 BOARD 1 harness (SW/LED) 4 LED shield 2 screws (SW) (No.6-32UNC) 3 SWX-66 board 2-17. FDD 3 Push the lever. 4 Remove the FDD bracket ass’y in the direction of arrow A . 1 harness (FDD) 2 harness 5 two screws (PWH3 ×...
2-19. MEMORY (DIMM) 1 Open two clips. 2 memory (DIMM) × 2 1 Open two clips. Note 1: In opening the clips, hold lightly the top of the memories with your fingers to prevent a drop. Note 2: In removing the memories, always start from the one having largest bank number.
Page 16
(DDR) 1 Open two clips. 2 memory (DDR) × 2 1 Open two clips. Note 1: In opening the clips, hold lightly the top of the memories with your fingers to prevent a drop. Note 2: In removing the memories, always start from the one having largest bank number.
2-20. CPU 1 harness 4 Elect the lever in the direction of arrow A . 2 clip 5 CPU 3 DC fan (with heat sink) 1 harness 2 clip 5 CPU 3 DC fan (with heat sink) 4 Elect the lever in the direction of arrow A .
• CPU INSTALLATION Note : When heat sink is removed from CPU, install new ones after thermal diffusion grease is wiped off and silicon compound is applied to the place shown in the figure. Thermal diffusion grease : silicon compound (G-765) 90G Amount to apply : 0.1 g (as the same size as the tip of a match) (Celeron) 0.5 g (as the same size as the tip of a match) (Pentium 4)
SECTION 3 PROGRAM FOR SERVICE 3-1. General DISKETTE TEST FDD is tested. As the read/write operation is performed to the floppy disk, The Diagnostic Programs for Service are available with the fol- set the DOS formatted 1.44M disk without the write protec- lowing three kinds.
SECTION 4 SERVICE INFORMATION 4-1. JUMPER SETTING ON HARD DISK DRIVE The hard disk drive of service parts can be used without changing factory jumper setting, when it was replaced for service. Capacity Part No. Maker Code Memo (formatted) A-8110-897-A Seagate ST340810A 40 GB...
SECTION 5 FRAME HARNESS 5-1. CONNECTOR LIST MOTHER BOARD (BI) PGA370 socket Internal connector Coppermine-128k, Coppermine-256K , Tualatin-128K, Tualatin-256K supported Power supply Connector location on MB See the frame harness daigram 20pin ATX t ype connector. Connector location on MB See the frame harness daigram Pin assignments: PCI Slot x3...
Page 23
CD audio I/O header 4 pin standard 2mm single line header for CD Audio signal input 20 pin standard 2.5mm dual line header for LED/Switch unit Connector location on MB See the frame harness daigram Connector location on MB See the frame harness daigram Pin assignments: Pin assignments: Signal Name...
Page 24
Line In pin assignments: IEEE1394 Rear connector Signal Name 6 pin standard IEEE1394 Rear connector. Sleeve Ground Connector location on MB See the frame harness daigram Audio Left In Pin assignments: Ring Audio Right In Signal Name VP (Power ) Microphone In pin assignments: Ground Signal Name...
MOTHER BOARD (AN) 2-1 Internal connector CD audio Power supply 4 pin standard 2mm single line header for CD Audio signal input 20 pin ATX type connector. Connector location on MB See the frame harness diagram Pin assignments: Connector location on MB See the frame harness diagram Signal Name 4 pin ATX12V type connector.
Page 26
USB/LAN I/O header One USB connectors for external USB devices (Support the stacked connector) 20 pin standard 2.5mm dual line header for LED/Switch unit One 10/100Base-T connector Connector location on MB See the frame harness diagram Pin assignments: Connector location on MB See the frame harness diagram Pin assignments: Signal Name...
MOTHER BOARD (EE) 3-1 Internal connector IEEE1394 access header x2 Power supply 8 pin standard 2.5mm single line header for IEEE1394 Front connector. Connector location on MB See the frame harness diagram 20 pin ATX type connector. Pin assignments: Connector location on MB See the frame harness diagram Signal Name Shell Ground...
Page 28
USB/LAN One USB connectors for external USB devices (Support the stacked connector) One 10/100Base-T connector Connector location on MB See the frame harness diagram Pin assignments: Signal Name Signal Name ACTLEDP LANP8 ACTLEDN LANP8 LILEDP USBVCC1 LILEDN USBP1- TXPCON UCBP1+ TXNCON RXPCON LANP5...
SECTION 6 REPAIR PARTS LIST NOTE: • The parts listed here are for service, and therefore they may be different The components identified by from the parts shown in circuit diagrams or used in the set. mark 0 or dotted line with mark •...
MEMO 6-4. ACCESSORIES AND PARTS LIST POWER CORD (1) CONVERSION CONNECTOR (VIDEO CONNECTING) (2) ANTENNA CABLE (1) i. LINK CABLE (1) VIDEO CABLE (1) KEYBOARD (1) REMOTE COMMANDER (1) MOUSE (1) RAY-CATCHER UNIT (1) AUDIO CABLE (1) AC ADAPTOR (1) SPEAKER UNIT (1) MODEM CABLE (1) Confidential...
Page 37
Ref.No. Part No. Description RX690G RX682 RX681 RX680G RX672 RX671 RX670 RX660 RX651 RX650 RX641 RX640 RX600E RX600N 4-648-912-02 PANEL, LEFT 4-648-912-41 PANEL, LEFT X-4624-140-1 LEFT CHASSIS ASSY 1-468-417-72 POWER, SWITCHING 1-468-601-14 POWER UNIT X-4624-060-1 BRACKET PS (280W) ASSY X-4624-061-1 BRACKET PS (150W) ASSY 4-635-795-01 SCREW (NO.6-32UNC)
Page 38
CRIMM (YODA) 4-648-884-11 PANEL, BLANK A-8067-057-A IFX-185 MOUNTED PWB A-8067-157-A CNX-169 MOUNTED PWB 4-657-321-21 ADAPTOR (SONY), DRIVE z z z z z z z z 4-657-322-21 ADAPTOR (PIONEER), DRIVE z z z z z z z z 4-657-322-21 ADAPTOR (PIONEER), DRIVE...
Page 39
ACCESSORIES & PACEKING MATEIRALS ****************************************************** Ref.No. Part No. Description RX690G RX682 RX681 RX680G RX672 RX671 RX670 RX660 RX651 RX650 RX641 RX640 RX600E RX600N 4-662-040-11 USER GUIDE 4-662-043-11 GETTING STARTED GUIDE (RX) 1-777-786-11 CORD, AC 1-777-801-21 CORD, CONNECTION (F TYPE RF) 1-777-802-21 CORD, CONNECTION (VIDEO) 1-772-704-71...