Advertisement
Quick Links
HUAWEI USG6310/6320 Unified Security Gateway
V100R001
Quick Start
Issue: 04
Part Number: 31507267
Date: 2015-06-18
Thank you for using Huawei USG6310/6320 products. This USG product series protects your network against Internet
threats. This Quick Start shows the product appearance and provides the essential information required for installing the
device and setting up Internet access. For detailed hardware description and installation guidelines, refer to the
Guide
. For detailed configurations, refer to the
Safety Precautions
Be aware of the following safety precautions when installing the device.
• Deactivate power whenever possible before performing maintenance on power cables.
• Always wear a properly-grounded wrist strap before touching the device or expansion cards in it.
Device and Accessories
Your product package includes the following items:
Secospace USG6000
PWR SYS ALM USB
Indicators
Equipment
Serial Number
XXXXXXXXXXXXXXXXXXXXXXXXXXX
CONSOLE
10/100/1000M autosensing
Console port
Ethernet electrical interface
• The rack-mounting ear is optional.
• AC power cables vary by country or area, and the AC power cable in the figure is used for reference only.
Cabling
1. Connect the ground terminal on the device to the ground bar using a PGND cable.
2. Connect the device to the WAN and LAN through Ethernet ports (GE0/0/4 and GE0/0/6 in this example, respectively).
3. Connect the device' interface GE0/0/0 to a PC where the NMS client is installed using a network cable.
4. Insert the cable retention clip into the hole close to the power socket. Connect the AC power cable to power adapter, and
insert the 4-pin self-locking plug of the power adapter into the power socket on the device. Then round the clip over the
power cable and fix it using the clip. Insert the AC power cable plug into the power supply socket.
As USG does not provide a power switch, it starts up immediately after receiving power. When the SYS indicator
on the SPUA panel is blinking (once every two seconds), the device is running and ready for configuration.
Administrator Guide
1
3
5
7
0
2
4
6
ETH
Port indicators
USB
Protection ground
terminal
1
3
5
7
Secospace USG6000
RST
12V ; 3A
0
2
4
6
Power
Reset button
.
Rack-mounting ears
M4 screw
AC power cable
Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.
1
All other trademarks and trade names mentioned in this document are the
property of their respective holders.
Hardware
Rubber feet
Quick start
M6 screw
Power Cable
retention clip
36W power adapter
PGND cable
Advertisement
Related Manuals for Huawei USG6310
Summary of Contents for Huawei USG6310
- Page 1 Issue: 04 Part Number: 31507267 Date: 2015-06-18 Thank you for using Huawei USG6310/6320 products. This USG product series protects your network against Internet threats. This Quick Start shows the product appearance and provides the essential information required for installing the Hardware device and setting up Internet access.
- Page 2 Rear panel Secospace USG6000 XXXXXXXXXXXXXXXXXXXXXXXXXXX CONSOLE 12V ; 3A GE0/0/0 GE0/0/4 GE0/0/6 Switch Administrator Intranet Default Configuration The following table lists the default configuration. Item Description GE0/0/0 The IP address is 192.168.0.1. Administrator account/password You can use the default account/password (admin/Admin@123) to log in through web or console.
- Page 3 5. In the Time Settings step, configure the system clock of the device according to your local time zone, and click Next. 6. In the WAN Mode step, select a WAN mode and click Next. 7. In the WAN Settings step, set the parameters and click Next. 8.
- Page 4 License Authorization Code field. 5. Click Activate to activate the license. • Obtaining Product Documents The latest documents of all products are published at the technical support website (http://support.huawei.com/enterprise) of Huawei Technologies Co., Ltd.. • Obtaining Technical Support Contact your local representative for further information.