Pioneer XY-81 Installation Manual

Xy series 8-inch two-way loudspeaker / 10-inch two-way loudspeaker / 12-inch two-way loudspeaker / 15-inch two-way loudspeaker / three-way bi-amp loudspeaker / 15-inch bass reflex subwoofer / 18-inch bass reflex subwoofer / dual 15-inch quasi-bandpass sub

Hide thumbs Also See for XY-81:

User manual (12 pages)

Installation manual (92 pages)

Installation manual (78 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual See also: User Manual

XY-81

8-inch two-way loudspeaker

XY-101

10-inch two-way loudspeaker

XY-122

12-inch two-way ｌoudspeaker

XY-152

15-inch two-way ｌoudspeaker

XY-3B

Three-way bi-amp loudspeaker

XY-115S

15-inch bass reflex Subwoofer

XY-118S

18-inch bass reflex Subwoofer

XY-215S

Dual 15-inch quasi-bandpass subwoofer

XY-218S

Dual 18-inch bass reflex Subwoofer

Loudspeaker XY Series

Installation manual

http://pioneerproaudio.com/

Version 4.0 Oct 2017

Table of Contents

Summary of Contents for Pioneer XY-81

Page 1: Installation Manual
XY-152 15-inch two-way ｌoudspeaker XY-3B Three-way bi-amp loudspeaker XY-115S 15-inch bass reflex Subwoofer XY-118S 18-inch bass reflex Subwoofer XY-215S Version 4.0 Oct 2017 Dual 15-inch quasi-bandpass subwoofer XY-218S Dual 18-inch bass reflex Subwoofer ©2017 Pioneer DJ Corporation All rights reserved...
Page 2: Table Of Contents
5.1.2 XY-122/152 P.52 5.2 Three-way loudspeaker P.55 P.55 5.2.1 XY-3B 5.3 Subwoofer P.60 P.60 5.3.1 XY-115S/118S/218S P.63 5.3.2 XY-215S P.65 5.3.3 XY-218HS 6 Specifications 6.1 Spec sheet P.67 6.2 drawing P.71 Page 2 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 3: Introduction
Pioneer DJ shall accept no liability for damage or injury caused by accidents resulting from Pioneer products tipping over or falling due to them being insufficiently secured.
Page 4: About Trademarks And Registered Trademarks
Do not use headphones while operating a motorised vehicle; the use of headphones may create a traffic hazard and is illegal in many areas. About trademarks and registered trademarks ・Pioneer is a registered trademark of PIONEER CORPORATION. ・SpeakON is a registered trademark of Neutrik. The names of companies and products mentioned herein are the trademarks of their respective owners.
Page 5: Installation Guidelines
Take measures to prevent a speaker from sliding off a shelf or a stage, etc. Full-range loudspeakers The XY-81, XY-101, XY-122 and XY-152 come with pre-inserted mounting screws. These screws can be taken out and used to attach either special mounting hardware designed for the product or commercially available mounting hardware.
Page 6: System Set-Up
Damage to the ear can result from levels above 90 dB under prolonged exposure. Stand mounting The XY-81, XY-101, XY-122 and XY-152 can be mounted from a loudspeaker stand using the integral polemount adapter for a standard 35 mm (1.4 in.) loudspeaker stand.
Page 7: Accessories
(see Table 2-1 and 2-2 "Accessories List") Please ensure that you read "Section 1: Introduction" and "Section 3.1 - 3.2" fully, and have the product installed by a professional. Have the installer carefully follow the installation instructions. Page 7 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 8 XY-218S XY-218HS 2 x M20 Hardware polemount Speaker Pole polemount polemount standby sockets socket socket (top,right side) Accessories Caster set CP-XYCS1 CP-XYCS1 CP-XYCS1 CP-XYCS1 List Refer to 　Setting procedure Section 3.2.7 Page 8 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 9 White socket cover seal for the white models Applicable models: XY-81-W : 1 piece of white seal is shipped with XY-81-W. XY-101-W : 1 piece of white seal is shipped with XY-101-W. XY-122-W : 1 piece of white seal is shipped with XY-122-W.
Page 10: Rigging And Caster Setting
Eye bolts to be used as secondary safety feature are not included with the products. When you use any commercially-available eyebolts, the above- listed safe working load limits and other specifications should be met. Page 10 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 11 (1) Make a small slit around the pre-inserted screws using an appropriate cutting knife. (2) Carefully remove the screws using a screwdriver, and ensure the cabinet coating is not peeled off. Page 11 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 12: Horn Rotation
3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.1.2 Horn rotation HF dispersion orientation on XY-81/101/122/152 can be changed by rotating the HF waveguide 90 degrees. (Fig.3-1-3-A) NOTE: XY-122 is shown in the illustration 90 deg 60 deg After rotating Factory default...
Page 13 Reinstate the bolts and retighten. Avoid over tightening as this may crack the waveguide. Reinstate the grille by gently placing it in place over the front of the loudspeaker. Reinstate the bolts to secure it in place. Fig.3-1-2-C Page 13 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 14: Logo Badge Replacement
3 Rigging And Caster Setting __________________________________________________________________________________________________________ 3.1.3 Logo badge replacement The location of Logo badge attached to the grilles on XY-81/101/122/152 can be changed. Required tools XY-81 / XY-101 XY-122 / XY-152 ・Phillips head screwdriver ・3mm hex key ・Phillips head screwdriver ・4mm hex key...
Page 15 __________________________________________________________________________________________________________ CAUTION: XY-81/101 Location where the Logo badge should be attached: The Logo badge can be attached to only the limited locations on the grille. Please see the Fig.3-1-3-F, G, H, I. If the Logo badge is attached to other locations than the specified ones, the speaker could be damaged.
Page 16 DO NOT ATTACH THE LOGO BADGE 5 holes 9 holes DO NOT ATTACH THE LOGO BADGE. GRAY AREA Any part of the LOGO BADGE should not protrude to the gray area. Fig.3-1-3-G For horizontal installation (XY-81) Page 16 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 17 A plate supporting the grille DO NOT ATTACH THE LOGO BADGE. GRAY AREA Any part of the LOGO BADGE should not protrude to the gray area. Fig.3-1-3-I For horizontal installation (XY-101) Page 17 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 18: Procedures
For all the models, the following situations are quite dangerous. Suspending from sloped Suspending Suspending (non-horizontal) ceiling from the wall multiple Only for the following model: CP-XY8VC1/XY10VC1/XY15VC1 Inclining over 75 deg (XY-81/101), 45 deg (XY-152) Page 18 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 19: Vertical Flying Cradle
Page 19 / 80 M10 s ocket hea d bol t 06B522 M10 x 20mm (P=1.5), http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION 8mm hex s ocket hea d Spri ng Wa s her 06D015 Fl a t wa s her 06D014...
Page 20 Using the supplied two M8 countersunk bolts(B), align the mounting holes in the inner yoke of the Vertical Flying Cradle(A) with the mounting points on the top of the enclosure. Tighten the bolts over 7N·m torque. Page 20 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 21 Ensure the commercially-available eyebolt is secured to the mounting point to suspend it with wire as a secondary safety feature. (Fig.3-2-1-F) Only XY-152 Commercially- available Fig.3-2-1-F Page 21 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 22 (Fig.3-2-1-I) Ensure the commercially-available eyebolt is secured to the mounting point to suspend it with wire as a secondary safety Fig.3-2-1-I feature. (Fig.3-2-1-J) Commercially- available eyebolt Fig.3-2-1-J Page 22 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 23: Horizontal Flying Cradle
Available Available prohibited Note: The dispersion orientation when placing the XY-81/101/122/152 enclosure horizontally will be changed from the orientation when placing it vertically. Rotate the horn inside of the enclosure to reverse the dispersion orientation to the original orientation when it is placed vertically. Also, the location and the orientation of the logo badge can be changed.
Page 24 Mounting Plate Neoprene Washer 05B010 40mm x 2mm Flat Washer 06D009 ・6mm hex key Spring Washer 06D011 Knob 05A101 M8 x 30mm (P=1.25), M8 socket head bolt 06G046 6mm hex socket head Page 24 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 25 Note: The yoke length can be changed by unscrewing the lever and choosing mounting holes in the both plate ends of the Horizontal Flying Cradle. Remove the four pre-inserted mounting screws on the top and the bottom of XY-81/101/122/152. (XY-81/101/122: Fig.3-2-2-A), (XY-152: Fig.3-2-2-B) XY-152 XY-122/101/122 Fig.3-2-2-B...
Page 26 Fig.3-2-2-E feature. (Fig.3-2-2-F) NOTE: XY-122 is shown in the illustration. Commercially -available eyebolt Fig.3-2-2-F NOTE: XY-122 is shown in the illustration. Page 26 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 27: Variable Angle Bracket
3pcs Front Back Wide Narrow NOTE: A serial label is stuck on the front of the angle bracket. NOTE: XY-122 and CP-XY12AB1 is used in the illustration below. +17° -31° Fig.3-2-3-A Page 27 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 28 M10 x 40mm (P=1.5), M10 hex head bolt 06C007 ・8mm hex key 16mm hex head Spring washer for (D) 06D015 Flat washer 06D014 06E012 16mm width across flat ・16mm hex spanner Page 28 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 29 Note: For larger down-tilt angles, position the pivot on the last hole and use the point on the rear or underside as a pull-back. The hole (φ13) on the hook-clamp(B) can be used to install the speaker to the ceiling. (Fig.3-2-3-D) Fig.3-2-3-D Page 29 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 30 Ensure the commercially-available eyebolt are secured to either right Commercially -available or left mounting point on the top of the enclosure to suspend it with eyebolt wire as a secondary safety feature. (Fig.3-2-3-E) Fig.3-2-3-E Page 30 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 31: Dual Enclosure Flying Plate Set(*Dual + Variable)
Dual Enclosure Flying Plate Set is not supposed to be used in the following situations, which may cause an injury or accident. A° B° B deg A deg ≠ A deg B deg Suspending Suspending from sloped Unsymmetry (non-horizontal) ceiling Over 2 enclosures placement Page 31 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 32 Spring washer(C) and Flat washer(D) are used in between the Dual enclosure flying plate(A) and the M10 socket head bolt(B). Tighten the bolts at 15N·m torque. (Fig.3-2-4-B) NOTE: XY-122 is shown in the illustration. Fig.3-2-4-A Fig.3-2-4-B Page 32 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 33 Remove the two mounting screws pre-inserted in the M10 holes on the side of the XY-122/152 enclosure. (Fig.3-2-4-F) The XY-122/152 enclosure can be suspended from the ceiling when using two commercially-available M10 eyebolts as shown in the figure below. Fig.3-2-4-F (Fig.3-2-4-G) Page 33 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 34 A deg B deg ≠ A deg B deg Suspending from sloped Suspending Suspending Unsymmetry (non-horizontal) ceiling from the wall Over 2 enclosures placement Page 34 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 35 Variable Angle Bracket to the plate and place the Variable Angle Bracket in the right position to align its front and the ( I ) top front of the plate. Front Back Fig.3-2-4-I Page 35 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 36 Hook-clamp(J) and M10 socket head bolt(K) as well as the nut(O) and the hook-clamp(J). (Fig.3-2-4-L) The hole (Φ13) on the Hook-clamp(J) can be used to install the speaker to the ceiling. (Fig.3-2-4-L) Page 36 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 37 Since eyebolts should be mounted to the enclosure as secondary safety feature, the angle between the 2 enclosures should be between minimum degrees and maximum degrees in order to mount the eyebolts. Fig.3-2-4-L Commercially -available Fig.3-2-4-M Page 37 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 38: Suspension Of Enclosure Using The Eye Bolt
3 Rigging And Caster Setting ___________________________________________________________________________________________________________ 3.2.5 Suspension of the enclosure using the eyebolt The XY-81/101/122/152/3B enclosure has the mounting points where commercially-available eyebolts can be mounted. Using the commercially-available eyebolts, a XY-81/101/122/152/3B enclosure or a combination of them can be vertically or horizontally suspended.
Page 39 For all models : Over 120 kg Suspending horizontally using eyebolts Not suspending Only for the following models : XY-81 / 101 / 122 / 152 Suspending using M8 bolt Suspended by 1 line of Suspending holes for wall mount brackets...
Page 40 3 Rigging And Caster Setting ___________________________________________________________________________________________________________ If eyebolts are secured to the rear side of the XY-81/101/122/152/3B enclosure for suspension, the enclosure can be inclined downward. The locations and number of mounting points of each model are listed in the Table.3-2-5-A.
Page 41: Wall Mount Bracket
The holes for commercially-available wall mount brackets are provided on the rear of the XY-81/101/122/152. Note: Pioneer does not sell wall mount brackets. Please ensure that the commercially-available wall mount bracket is compatible with the sizes shown in Table 3-2-6-A Table 3-2-6-A: Size of the hole and the area for a wall mount bracket to be attached.
Page 42: Caster
- the Flat washer(C) should be in contact with the Caster(A). Tighten the bolts at 7N·m torque. (Fig.3-2-7-B) Turn the XY-118S/215S/218HS enclosure with its grille up to roll on the casters. (Fig.3-2-7-C) Fig.3-2-7-A Fig.3-2-7-C Fig.3-2-7-B Page 42 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 43: Wheel Board
Also, when raising up the enclosure after transportation, be sure to Fig.3-2-8-A lock the lock casters. ・Be sure to lock the lock casters except during transportation. Locking Castor Fig.3-2-8-B Page 43 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 44: System Configuration
Impedance 8Ω 8Ω 4Ω 4Ω 4Ω Power 700W 1000W 800W 1600W 1400W Program 1400W 2000W 1600W 3200W 2800W Handling Recommended K3DSP K10DSP K3DSP K10DSP K10DSP Amplifier Minimum K3DSP K2DSP K6DSP K6DSP Page 44 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 45 M30DHDSP 8Ω 900W x 2ch 4Ω 1200W x 2ch M20DHDSP 8Ω 600W x 2ch 4Ω 3000W x 8ch 8Ω 1600W x 8ch X-Series 4Ω 3000W x 4ch 8Ω 1600W x 4ch Page 45 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 46 Given below are the recommended maximum cable lengths for different cross-sections and impedances. Maximum Recommended Cable Length Conductor Cross Sectional Area 4 Ω 8 Ω 16 Ω 1.0mm 1.5mm 2.0mm 2.5mm 116m 4.0mm 176m 6.0mm 132m 264m XY-3B XY-81/101/122/152 XY-215S/218S/218HS XY-115S/118S Page 46 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 47 OUT1 1+ : Speaker 1+ OUT1 1+ : Speaker 1+ 1- : NC 1- : Speaker 1- OUT2 2+ : NC OUT2 1+ : Speaker 2+ 2- : Speaker 1- 1- : Speaker 2- Page 47 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 48: Drive Unit Replacement
Part list Grille XY-81 Note Item Part Name Service Part No. Required tools ・3mm hex key Grille 04X901 Grille M4 x 20mm (P=0.7) M4 socket head bolt 06G016 3mm hex socket head Page 48 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 49 Service Part No. Required tools ・4mm hex key LF drive unit PT-XY101LF1 M5 x 30mm (P=0.8) M5 socket head bolt 06G001 4mm hex socket head Flat washer 06D003 Spring washer 06D005 Page 49 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 50 Remove the four socket head bolts from the HF waveguide. Lift the waveguide up and remove the cables from the HF drive unit. XY-81: Remove the two packing from the inside of the horn. Insert an hex key into the two slits appearing after the packing was...
Page 51 Remove the socket head bolts from the LF drive unit. The number of socket head bolts to be removed from XY-81 is 8 and from XY-101 is 4. Lift the LF drive unit up and remove the cables from the LF drive unit.
Page 52: Xy-122/152
Remove the grille from the enclosure. Reverse the above steps when placing the grille back to the enclosure. The grille should be placed back in the same orientation before it was removed. Page 52 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 53 Replace the LF drive unit with a new one. Connect the cables to the two terminals. Red Terminal (+) Brown cable Blue cable Brown cable Black Terminal (-) : Blue cable Black terminal Red terminal Page 53 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 54 Ensure that the terminals of the drive unit are placed as shown below. Location of Tighten the bolts to ensure a solid fit to the grille. terminals Additional information (XY-122/152) For the connection information, please refer to following circuit diagram. Page 54 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 55: Xy-3B
Remove the grille from the enclosure. Reverse the above steps when placing the grille back to the enclosure. The grille should be placed back in the same orientation before it was removed. Fig.5-2-1-A Page 55 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 56 Removing and reinstalling the moulded Bi-horn Set. To replace the MF/HF drive unit, you need to remove the moulded Bi-horn from the cabinet. Remove twelve M6 countersunk bolts from the Horn. (Fig.5-2-1-E) Fig.5-2-1-E Page 56 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 57 Black Terminal (-) : Yellow cable Fig.5-2-1-G Replacement of MF drive unit Remove the two waddings from the heat sink. (Fig.5-2-1- Fig.5-2-1-H Remove the eight socket head bolts from the MF chamber. (Fig.5-2-1-I) Fig.5-2-1-I Page 57 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 58 Bi-Horn in the same orientation as before replacing the drive unit. Tighten twelve M6 countersunk bolts of the moulded Bi- Fig.5-2-1-M-1 Horn and two M10 countersunk bolts of the cabinet. Page 58 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 59 5 Drive unit replacement ___________________________________________________________________________________________________________ Additional information (XY-3B) For the connection information, please refer to following circuit diagram. Page 59 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 60: Subwoofer
Required tools Item Part Name Qty Service Part No. Note ・5mm hex key Drive unit PT-XY118SL1 M6 x 40mm (P=1.0), M6 socket head bolt 06G003 5mm hex socket head Spring washer 06D0075 Page 60 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 61 Black Terminal Tighten the socket head bolts on the LF drive unit. Tighten the screw to ensure a solid fit to the grille. XY-118S XY-115S Location of Location of terminals terminals XY-218S Page 61 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 62 5 Drive unit replacement ___________________________________________________________________________________________________________ XY-218S Location of Location of terminals terminals Additional information (XY-115S/118S/218S) For the connection information, please refer to following circuit diagram. XY-115S/118S XY-218S Page 62 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 63: Xy-215S
Reinstall the LF drive unit to the enclosure. Tighten the socket head bolts on the LF drive unit. Tighten the countersunk bolts to ensure a solid fit to the grille. Left drive unit Right drive unit Page 63 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 64 5 Drive unit replacement ___________________________________________________________________________________________________________ Location of terminals Location of terminals (Right drive unit) (Left drive unit) Additional information (XY-215S) For the connection information, please refer to following circuit diagram. Page 64 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 65: Xy-218Hs
Reinstall the LF drive unit to the enclosure. Tighten the socket head bolts on the LF drive unit. Location of terminals Tighten the bolt to ensure a sodoor fit to the door. Front Back Red Terminal Black Terminal Page 65 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 66 5 Drive unit replacement ___________________________________________________________________________________________________________ Additional information (XY-218HS) For the connection information, please refer to following circuit diagram. Page 66 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 67: Specifications
Accessories (-W model only) (-W model only) (-W model only) (-W model only) The specifications and design of this product are subject to change without notice. Page 67 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 68 15 mm (0.6 inch) birch plywood Impact-resistant, Black semi-matt Finish textured Suggested Power Recommended : X4 Amplifier — Accessories The specifications and design of this product are subject to change without notice. Page 68 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 69 2 x polemount socket cover — Accessories (-W model only) (-W model only) (-W model only) The specifications and design of this product are subject to change without notice. Page 69 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 70 18 mm (0.7 inch) birch plywood Impact-resistant, Black semi-matt Finish textured Suggested Power Recommended : K10DSP Amplifier — Accessories The specifications and design of this product are subject to change without notice. Page 70 / 80 http://pioneerproaudio.com/ ©2016 Pioneer DJ CORPORATION...
Page 75: Drawing
6 Specifications 6.2 Drawing NOTE: The nuts of the threaded fixing points on XY-3B are structured so that bolts cannot pass through them. (max threaded length is 15mm.)

This manual is also suitable for:

Xy-122 Xy-152 Xy-3b Xy-101 Xy-115s Xy-118s ... Show all

Pioneer XY-81 Installation Manual

1 Introduction

2 Accessories

3 Rigging and Caster Setting

4 System Configuration

5 Drive Unit Replacement