hit counter script
Sony PMW-200 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Camcorder
  5. PMW-200
  6. Service manual

Sony PMW-200 Service Manual

Solid-state memory camcorder
Hide thumbs Also See for PMW-200:
Table of Contents

Advertisement

Quick Links

SOLID-STATE MEMORY CAMCORDER
PMW-200
PMW-EX280
SERVICE MANUAL
1st Edition (Revised 1)

Advertisement

Table of Contents
loading

Related Manuals for Sony PMW-200

Summary of Contents for Sony PMW-200

  • Page 1 SOLID-STATE MEMORY CAMCORDER PMW-200 PMW-EX280 SERVICE MANUAL 1st Edition (Revised 1)
  • Page 2 Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. PMW-200/PMW-EX280...
  • Page 3 Batterien nur durch den vom Hersteller empfohlenen Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. PMW-200/PMW-EX280...

  • Page 5: Table Of Contents

    IO-254 Board......................2-10 PMW-200/PMW-EX280...
  • Page 6 Error Code List.......................3-13 PMW-200/PMW-EX280...
  • Page 7 Frame Wiring......................... . .7-1 PMW-200/PMW-EX280...

  • Page 9: Manual Structure

    Manual Structure Purpose of this manual This document is the service manual of Solid-State Memory Camcorder PMW-200/EX280 When servicing this unit, parts are replaced on a board basis in principle. Therefore, this manual includes no circuit diagram or board layout.

  • Page 11: Service Overview

    2. TC IN/OUT 2-Pin, DC JACK TYPE 4 Both IN and OUT, BNC type TC IN: 0.5 V to 18 Vp-p EXT DC TC OUT: 1.0 Vp-p, 75 Ω, Unbalanced - External View - 3. HEADPHONE Stereo mini jack PMW-200/PMW-EX280...
  • Page 12 Composite OUT 5-pin, mini-B, USB2.0 Hi-Speed 11. HDMI - External View - 19-pin, Type A Signal Specifications — USB Vcc D– IN/OUT I/O USB– - External View - IN/OUT I/O USB+ — Signal Specifications — Ground TMDS DATA2+ — Continued PMW-200/PMW-EX280...
  • Page 13 USB (Series A), 4-pin - External View - Signal Specifications USB_VBUS — USB Vcc DATA (–) IN/OUT I/O USB– DATA (+) IN/OUT I/O USB+ — Ground 13. LENS REMOTE 8-pin, Female - External View - Signal Specifications COMMON –V Continued PMW-200/PMW-EX280...

  • Page 14: Location Of Printed Wiring Boards

    Location of Printed Wiring Boards BI-204A HN-384 VR-350 HN-399 BI-202A EC-75 SWC-54 SW-1579 DCP-56 SW-1578 SW-1577 DPR-343 SW-1573 SW-1559 HN-398 BI-203A HN-403 IO-255 CN-3540 IF-1188 RM-238 DR-670 HN-387 HN-404 RM-237 AXM-48 PSW-97 DC-167 FP-179 RE-299 RE-298 RE-300 KSW-62 IF-1182 AU-342 HN-386 KSW-61 DET-55 PMW-200/PMW-EX280...

  • Page 15: Circuit Description

    The digital video signal (Y/C) sent from the camera signal processor IC RISE (IC200) on the DCP-56 board is input to the baseband processing IC T-ONE (IC900). The baseband processing IC T-ONE that incorporates scaler functions (supporting multi-format output), OSD, PLL (54 to 74 MHz), and CPU performs baseband processing for video and audio signals. PMW-200/PMW-EX280...

  • Page 16: Media Recording/Playback System

    Controlled by the system controller (IC2101) in the same way as other main devices, the DPR-343 board performs video/ audio stream control, SxS memory card access, mass storage operation through the USB connection, and HDV device control through the i-LINK connection. PMW-200/PMW-EX280...

  • Page 17: Audio System

    Q104, Q103 and Q105) and outputs balanced audio signals. • When the LINE input level (+4 dBu) is selected for the EXT input signal, an input attenuator is inserted by switches (Q150 to Q153, Q158 to Q162). • A speaker is connected to the speaker connector (CN102). PMW-200/PMW-EX280...
  • Page 18 • Analog audio circuit control signals are output by the FPGA. Clock • The audio system clock is supplied from IC900 on theDCP-56 board to the FPGA and is distributed from the FPGA to the A/D converter and the D/A converter. PMW-200/PMW-EX280...

  • Page 19: System Control

    IC2101 (DPR-343 board). After that, it controls the power for each circuit block according to the system controller. The system controller controls the respective power supply systems in the RE-299 and RE-300 boards according to the operation mode of the device, via the power supply microcomputer (IC202) on the RE-298 board. PMW-200/PMW-EX280...

  • Page 20: Power Supply System

    Each power system monitors respective output voltages and the protection circuit is configured so that it works for each block. When a short-circuit is detected even in a single block, entire camera is shut down. The protection circuit is not automatically reset even after the short-circuit is cleared, and power must be turned on again. 1-10 PMW-200/PMW-EX280...
  • Page 21 In the specified battery pack, information such as the number of recycling times and the internal temperature can be monitored internally. This allows the operation with detailed information about the battery, including information whether the battery pack is damaged or has reached its lifetime. 1-11 PMW-200/PMW-EX280...

  • Page 22: Service Tools/Measuring Equipment List

    J-6252-510-A Torque driver (6 kg•cm) (0.6 N•m) 7-432-114-11 Locking compound 200 g For preventing screws from being loosened 7-651-000-10 Sony (SGL-601) 50 g grease Lubricant 1-4-2. Measuring Equipment Use the following calibrated equipment or equivalent for adjustments. Equipment Model name...

  • Page 23: Firmware Upgrade

    Install the upgrade software in the PC. Note For how to obtain the upgrade software, contact your local Sony Sales Office/Service Center. When a PC is connected to the unit for the first time, driver software need to be installed in the PC. For details, check the readme file supplied with the upgrade software.

  • Page 24: Circuit Protection Parts

    After that, replace the defective parts. Board name Ref.No. Address Part No. Rating IF-1188 PS100 A1 (Side A) 0.4 A/72 V 1-576-122-21 PS101 A1 (Side A) 0.4 A/72 V 1-576-122-21 RE-299 F100 A2 (Side B) 10A/125V 1-576-329-21 1-14 PMW-200/PMW-EX280...

  • Page 25: Notes On Service

    • RE-298 board • SWC-54 board When any of the following boards or part has been replaced, make adjustments again. For the adjustment method, contact your local Sony Sales Office/Service Center. • DCP-56 board • 3.5-inch LCD assembly • CMOS block 1-7-2.

  • Page 26: Flexible Card Wire And Fine-Wire Coaxial Cable

    • When disconnecting the fine-wire coaxial cable, be sure to hold the connector. Do not attempt to pull the cable. • Check that the contact surface of the fine-wire coaxial cable connector is free from dirt or dust. 1-16 PMW-200/PMW-EX280...
  • Page 27 Both sides of connector Hold the connector to disconnect. Do not attempt to disconnect by Fine-wire coaxial cable pulling the cable. Hold both sides of the fine-wire coaxial cable connector, and pull the connector straight to disconnect it. 1-17 PMW-200/PMW-EX280...
  • Page 28 Connecting Both sides of connector Fine-wire coaxial cable Note When connecting the fine-wire coaxial cable, insert it straight into the connector. Insert firmly the connector of fine-wire coaxial cable in the interior. 1-18 PMW-200/PMW-EX280...

  • Page 29: Lead-Free Solder

    • The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-19 PMW-200/PMW-EX280...

  • Page 31: Replacement Of Main Parts

    Lithium battery Outside panel assembly Battery lid Bottom cover SxS slot assembly Inside panel assembly Handle assembly Rear panel assembly DCP-56 board IO-255 assembly Front panel assembly Front lens assembly DPR-343 board RE-299 board RE-298 board RE-300 board AU-342 board PMW-200/PMW-EX280...

  • Page 32: Lithium Battery

    Remove the precision screw (M2 x 5) to detach the battery lid. Remove the lithium battery with an insulated stick. Insulated stick Precision screw Lithium battery (M2 x 5) Battery lid Install the removed parts by reversing steps of removal. PMW-200/PMW-EX280...

  • Page 33: Bottom Cover And Tripod Washer

    Remove the four precision screws (M2.6 x 5) to detach the bottom spacer and tripod washer. Precision screws (M2 x 5) Precision screws (M2 x 5) Bottom cover Precision screws (M2.6 x 5) Tripod washer Bottom spacer Install the removed parts by reversing steps of removal. PMW-200/PMW-EX280...

  • Page 34: Inside Panel

    Install the removed parts by reversing steps of removal. 2-4-2. SW-1577/SW-1578/SW-1579 Board Preparation Remove the battery lid. (Refer to “2-2. Lithium Battery”.) Remove the bottom cover. (Refer to “2-3. Bottom Cover and Tripod Washer”.) Remove the inside panel assembly. (Refer to “2-4-1. Inside Panel Assembly”.) PMW-200/PMW-EX280...
  • Page 35 Position the SW bracket A at three points and the SW bracket B at two points when installing them. SW bracket B SW bracket A Positioning locations Positioning locations Remove the SW conductivity sheet from the SW bracket A. SW conductivity sheet SW bracket A PMW-200/PMW-EX280...

  • Page 36: Sxs Lid Assembly

    Battery”.) Remove the bottom cover. (Refer to “2-3. Bottom Cover and Tripod Washer”.) Remove the inside panel assembly. (Refer to “2-4-1. Inside Panel Assembly”.) Procedure Remove the two tapping screws (2 x 5) to detach the lid shaft retainer. PMW-200/PMW-EX280...

  • Page 37: Au Cover Sub Assembly

    Remove the two parallel pins to detach the AU cover sub assembly. Note The parallel pins are press-fit. Use a tool to remove them. Parallel pin Tapping screw (2 x 5) Washer AU shaft retainer Parallel pin AU cover sub assembly PMW-200/PMW-EX280...
  • Page 38 Install the removed parts by reversing steps of removal. PMW-200/PMW-EX280...

  • Page 39: Outside Panel

    Install the removed parts by reversing steps of removal. 2-5-2. Zoom Seesaw Assembly Preparation Remove the battery lid. (Refer to “2-2. Lithium Battery”.) Remove the bottom cover. (Refer to “2-3. Bottom Cover and Tripod Washer”.) PMW-200/PMW-EX280...

  • Page 40: Io-254 Board

    Install the removed parts by reversing steps of removal. 2-5-3. IO-254 Board Preparation Remove the battery lid. (Refer to “2-2. Lithium Battery”.) Remove the bottom cover. (Refer to “2-3. Bottom Cover and Tripod Washer”.) Remove the outside panel assembly. (Refer to “2-5. Outside Panel”.) 2-10 PMW-200/PMW-EX280...
  • Page 41 Procedure Remove the two screws to detach the USB ground plate and the IO-254 board. IO-254 board USB ground plate P3.5 x 5 Install the removed parts by reversing steps of removal. 2-11 PMW-200/PMW-EX280...

  • Page 42: Top Panel Assembly

    Remove the four screws. Remove the top panel, waterproof sheet (IN), and waterproof sheet (OUT). Precision screws Precision screws (M2 x 5) (M2 x 5) Waterproof sheet (OUT) Waterproof sheet (IN) Install the removed parts by reversing steps of removal. 2-12 PMW-200/PMW-EX280...

  • Page 43: Sxs Slot

    (EC-75 board) Precision screws (M2 x 4) CN300 (SWC-54 board) CN103 CN104 (AU-342 board) (SWC-54 board) CN103 Flexible board Flexible board (SWC-54 board) Precision screws (M2 x 4) Harness Install the removed parts by reversing steps of removal. 2-13 PMW-200/PMW-EX280...

  • Page 44: Au Volume Block

    Remove the two (a) precision screws (M2 x 4) to detach the AU hold plate. Remove the tapping screw (2 x 5) to detach the escutcheon. Disconnect the harness from the connector (CN100) on the SW-1575 board. Remove the three (b) precision screws (M2 x 4). 2-14 PMW-200/PMW-EX280...
  • Page 45 Inside shield plate Tape Remove the three precision screws (M2 x 4) to detach the EC-75 board. EC-75 board Precision screws (M2 x 4) Precision screws (M2 x 4) Install the removed parts by reversing steps of removal. 2-15 PMW-200/PMW-EX280...

  • Page 46: Front Panel

    Install the removed parts by reversing steps of removal. 2-8-2. SW-1559 Board/SW-1573 Board Preparation Remove the battery lid. (Refer to “2-2. Lithium Battery”.) Remove the bottom cover. (Refer to “2-3. Bottom Cover and Tripod Washer”.) Remove the inside panel assembly. (Refer to “2-4-1. Inside Panel Assembly”.) 2-16 PMW-200/PMW-EX280...
  • Page 47 (2 x 5) SW-1559 board Front panel assembly Knob Note Align the phase of the slide switch on the SW-1573 board and the knobs on the front panel assembly during installation. Install the removed parts by reversing steps of removal. 2-17 PMW-200/PMW-EX280...

  • Page 48: Rear Panel Assembly

    Remove the four (b) precision screws (M2 x 5) to detach the rear panel assembly. Rear panel assembly (b) Precision screws (M2 x 5) USB cap (a) Precision screw (M2 x 5) (b) Precision screws (M2 x 5) Install the removed parts by reversing steps of removal. 2-18 PMW-200/PMW-EX280...

  • Page 49: Cn-3540 Board

    Disconnect the harness from the connector CN103 on the CN-3540 board. Remove the two screws to detach the CN-3540 board. Flexible flat cable CN101 P2 x 4 Harness CN-3540 board CN103 Install the removed parts by reversing steps of removal. 2-19 PMW-200/PMW-EX280...

  • Page 50: Io-255 Board

    IO-255 assembly Precision screws (M2 x 4) Unsolder the coaxial connectors (BNC type) on the IO-255 board. Remove the IO-255 board in the arrow direction, and then remove the coaxial connectors (BNC type) and the V- OUT spacer. 2-20 PMW-200/PMW-EX280...
  • Page 51 Disconnect the flexible flat cable from the connector (CN102) on the IO-255 board. Flexible flat cable CN102 IO-255 board Coaxial connectors (BNC type) V-OUT spacer Solderings Install the removed parts by reversing steps of removal. 2-21 PMW-200/PMW-EX280...

  • Page 52: Dcp-56 Board

    Disconnect the HN-387 board from the connector CN2300 on the DCP-56 board. Disconnect the HN-384 board from the connector CN2402 on the DCP-56 board. Disconnect the three fine-wire coaxial cables from the three connectors CN001, CN303 and CN305 on the DCP-56 board. 2-22 PMW-200/PMW-EX280...
  • Page 53 If the radiation sheet has peeled off, attach a new one referring to the figure. Remove the four tapes, cushion main C, and cushion main A. Cushion main C Cushion main A DCP-56 board Tapes 10. Install the removed parts by reversing steps of removal. 2-23 PMW-200/PMW-EX280...

  • Page 54: Handle

    (M2.6 x 5) Handle assembly Precision scerws (M2.6 x 5) Precision scerws HN-404 board (M2.6 x 5) HN-403 board Tape (BT) Fine-wire coaxial cable IF-1182 board CN2301 CN104 (DCP-56 board) CN101 Install the removed parts by reversing steps of removal. 2-24 PMW-200/PMW-EX280...

  • Page 55: Control Switch Block (Gz92000)

    Install the removed parts by reversing steps of removal. 2-13-3. MIC Unit Preparation Remove the handle (upper) case assembly.(Refer to “2-13-2. Control Switch Block (GZ92000)”.) Procedure Remove the two precision screws (M2 x 5) to detach the hinge (front) cover assembly. 2-25 PMW-200/PMW-EX280...
  • Page 56 (M2 x 5) Disconnect the flexible board from the connector CN100 on the KSW-62 board. Remove the precision screw (M2 x 4) to detach the FP-179 board. Remove the two tapping screws (2 x 5) to detach the MIC case. 2-26 PMW-200/PMW-EX280...

  • Page 57: Evf Case Assembly

    Remove the two precision screws (M2 x 5) to detach the handle rear cabinet assembly. Remove the four precision screws (M2 x 4) to detach the rear (cold) shoe. Disconnect the harness from the connector CN101 on the DR-670 board. Remove the EVF harness sheet. 2-27 PMW-200/PMW-EX280...

  • Page 58: Lcd Assembly

    Remove the handle (upper) case assembly.(Refer to “2-13-2. Control Switch Block (GZ92000)”.) Remove the control panel assembly. (Refer to “2-13-3. MIC Unit”.) Procedure Peel off the tape (BT). Disconnect the harnesses from the connectors CN402 and CN403 on the KSW-62 board. 2-28 PMW-200/PMW-EX280...

  • Page 59: Det-55 Board

    Assembly”.) Procedure Remove the two precision screws (M2 x 5) and the two claws to detach the panel hinge cabinet T and the panel hinge cabinet B. Disconnect the harness from the connector CN100 on the DET-55 board. 2-29 PMW-200/PMW-EX280...

  • Page 60: Lcd Panel

    Remove the two precision screws (M2 x 5) and the two claws to detach the LCD cabinet. Peel off the tape 50 and the LCD conductive tape. Remove the main gasket (H). Remove the two precision screws (M2 x 4). 2-30 PMW-200/PMW-EX280...
  • Page 61 Peel off the tape 25. CN100 IF-1188 board CN300 Tape25 Ferrite core Flexible board Harness Hinge 10. Remove the panel retainer and panel ground plate, and then remove the LCD panel. 11. Peel off the UL tape W8L25. 2-31 PMW-200/PMW-EX280...

  • Page 62: Dr-670 Board/Rm-237 Board/Rm-238 Board

    Remove the EVF case assembly and rear (cold) shoe. (Refer to “2-13-4. EVF Case Assembly”.) Procedure Remove the two precision screws (M2 x 4) to detach the DR-670 board. Precision screws (M2 x 4) DR-670 board Disconnect the HN-404 board from the connector CN100 on the RM-237 board. 2-32 PMW-200/PMW-EX280...

  • Page 63: Axm-48 Board

    RM-238 board CN100 Install the removed parts by reversing steps of removal. 2-13-9. AXM-48 Board Preparation Remove the handle (upper) case assembly. (Refer to “2-13-2. Control Switch Block (GZ92000)”.) Remove the control panel assembly. (Refer to “2-13-3. MIC Unit”.) 2-33 PMW-200/PMW-EX280...
  • Page 64 (M2 x 5) Precision screws (M2 x 4) MIC bracket Remove the two push buttons. Remove the precision screws (M2 x 5) to detach the cable holder. Remove the four screws (PTT2.6 x 6) to detach the AXM-48 board. 2-34 PMW-200/PMW-EX280...

  • Page 65: 2-13-10. Ksw-62 Board/Ksw-61 Board/Speaker

    Disconnect the Three harnesses from the connectors CN102, CN402, and CN403 on the KSW-62 board. Disconnect the two flexible boards from the connectors CN100 and CN101 on the KSW-62 board. Remove the eight precision screws (M2 x 4). 2-35 PMW-200/PMW-EX280...
  • Page 66 CN403 CN402 CN101 CN100 CN102 Disconnect the KSW-61 board from the connector CN404 on the KSW-62 board. KSW-62 board CN404 KSW-61 board Remove the two precision screws (M2 x 4) and the speaker retainer to detach the speaker. 2-36 PMW-200/PMW-EX280...
  • Page 67 Remove the speaker holder and the speaker cushion from the speaker. Note The speaker cushion is attached to the speaker with double-sided adhesive tape. Precision screws (M2 x 4) Speaker retainer Speaker cushion Speaker Speaker holder Install the removed parts by reversing steps of removal. 2-37 PMW-200/PMW-EX280...

  • Page 68: Front Lens

    Precision screws (M2.6 x 5) Harness Front lens assembly AU-342 board CN102 Precision screws (M2.6 x 5) Harness Front bracket Install the removed parts by reversing steps of removal. 2-14-2. HN-399 Board Preparation Remove the battery lid. (Refer to “2-2. Lithium Battery”.) 2-38 PMW-200/PMW-EX280...
  • Page 69 P2 x 4 P2 x 4 P2 x 4 Remove the harness and three fine-wire coaxial cables from the six claws. Disconnect the two BI boards from the two connectors CN100, CN200 on the HN-399 board. Remove the two screws. 2-39 PMW-200/PMW-EX280...
  • Page 70 Fine-wire Hole coaxial cable (G) CN200 Fine-wire coaxial cable (R) Fine-wire coaxial cable (B) Claws Note When installing the HN-399 board, fit the boss with the hole. Disconnect the harness from the connector CN102 on the HN-399 board. 2-40 PMW-200/PMW-EX280...

  • Page 71: Prism Block Unit

    10. Remove the main heat spreader DCP. (Refer to “2-12. DCP-56 Board”.) 11. Remove the handle assembly. (Refer to “2-13-1. Handle Assembly”.) 12. Remove the front lens assembly. (Refer to “2-14-1. Front Lens Assembly”.) 13. Remove the HN-399 board. (Refer to “2-14-2. HN-399 Board”.) 2-41 PMW-200/PMW-EX280...

  • Page 72: Optical Nd Filter

    “2-3. Bottom Cover and Tripod Washer”.) Remove the inside panel assembly. (Refer to “2-4-1. Inside Panel Assembly”.) Remove the outside panel assembly. (Refer to “2-5-1. Outside Panel Assembly”.) Remove the top panel assembly. (Refer to “2-6. Top Panel Assembly”.) 2-42 PMW-200/PMW-EX280...

  • Page 73: Lens Unit

    “2-14-1. Front Lens Assembly”.) 13. Remove the HN-399 board. (Refer to “2-14-2. HN-399 Board”.) 14. Remove the prism block unit. (Refer to “2-14-3. Prism Block Unit”.) 15. Remove the optical ND filter. (Refer to “2-14-4. Optical ND Filter”.) 2-43 PMW-200/PMW-EX280...
  • Page 74 Preparation Remove the five screws to detach the front frame from the lens unit. Lens unit Front frame P2.6 x 5 Install the removed parts by reversing steps of removal. 2-44 PMW-200/PMW-EX280...

  • Page 75: Battery Case

    Harness Harness Harness Install the removed parts by reversing steps of removal. 2-15-2. DC-167 Board/PSW-97 Board Preparation Remove the battery lid. (Refer to “2-2. Lithium Battery”.) Remove the bottom cover. (Refer to “2-3. Bottom Cover and Tripod Washer”.) 2-45 PMW-200/PMW-EX280...
  • Page 76 Remove the two precision screws (M2 x 4) to detach the PSW-97 board. Harness CN100 CN100 Precision screws Harness DC-167 board (M2 x 4) Precision screws (M2 x 4) PSW-97 board Install the removed parts by reversing steps of removal. 2-46 PMW-200/PMW-EX280...

  • Page 77: Main Chassis

    Remove the front panel assembly. (Refer to“2-8-1. Front Panel Assembly”.) Remove the rear panel assembly. (Refer to “2-9. Rear Panel Assembly”.) Remove the IO-255 assembly. (Refer to“2-11. IO-255 Board”.) 10. Remove the DCP-56 board. (Refer to “2-12. DCP-56 Board”.) 2-47 PMW-200/PMW-EX280...

  • Page 78: Au-342 Board, Re-298 Board, Re-299 Board, And Re-300 Board

    Remove the SxS slot assembly. (Refer to “2-7-1. SxS Slot Assembly”.) Remove the front panel assembly. (Refer to “2-8-1. Front Panel Assembly”.) Remove the rear panel assembly. (Refer to “2-9. Rear Panel Assembly”.) Remove the IO-255 assembly. (Refer to “2-11. IO-255 Board”.) 2-48 PMW-200/PMW-EX280...
  • Page 79 CN100 CN202 CN2400 (DPR-343 board) HN-386 board 3 Precision screws Positioning pins (M2 x 4) U groove U groove Precision screw CN104 (M2 x 4) Precision screws (M2 x 4) AU-342board Remove the precision screws (M2 x 4). 2-49 PMW-200/PMW-EX280...
  • Page 80 12. Remove the three (b) precision screws (M2 x 4) to detach the bracket RE and the bracket (RE-299) from the RE-299 board. (a) Precision screws RE-299 board (M2 x 4) (b) Precision screws (M2 x 4) Bracet RE Bracket (RE-299) (b) Precision screw (M2 x 4) CN800 AU-342 board 2-50 PMW-200/PMW-EX280...
  • Page 81 13. Remove the five precision screws (M2 x 4) to detach the AU-342 board from the bracket AU. Precision screws Precision screws (M2 x 4) (M2 x 4) AU-342 board Bracket AU 14. Install the removed parts by reversing steps of removal. 2-51 PMW-200/PMW-EX280...

  • Page 83: Service Menu

    Description MAINTENANCE Adjustment of parameters RPN CORRECT Operations regarding the RPN correction INFORMATION Display of information on this unit and self-diagnosis Note The MAINTENANCE menu and the RPN CORRECT menu are available while a camera image is being displayed. PMW-200/PMW-EX280...

  • Page 84: Display/Hide The Service Menu

    Once the SERVICE menu is displayed, it is displayed instead of the ordinary setup menus by pressing the MENU button, unless the power is turned off. To Exit the SERVICE Menu Display Press the MENU button again. The display of the SERVICE menu is finished. PMW-200/PMW-EX280...

  • Page 85: Service Menu List

    Cursor Next — — Moves the correction point indicator cursor to the next address. Cursor Prev — — Moves the correction point indicator cursor to the previous address. Record — Execute, Cancel Registers the RPN. Continued PMW-200/PMW-EX280...

  • Page 86: Information Menu

    This item is not selectable.(Display only) Item11 — This item is not selectable.(Display only) Item12 — This item is not selectable.(Display only) Item13 — This item is not selectable.(Display only) Log Dump — Execute, Cancel Records the error log to media. PMW-200/PMW-EX280...

  • Page 87: Self-Diagnosis

    SHUTTER switch and the SETUP menu. Item Menu Submenu Setting for self-diagnosis SHUTTER switch — — CAMERA SET menu SLS/EX SLS — P.Cache Rec Setting OTHERS menu System 　 Country NTSC Area UDF/FAT HD/SD Format HD422 50/1080/59.94i PMW-200/PMW-EX280...

  • Page 88: Details Of Self-Diagnosis

    -1: Exceeding RPN max number 1 ,2 — 0x09 Reading/Writing data test to CMOS -1: CMOS Read/Write NG or CMOS 1 ,2 — block, video signal bus connection video signal bus NG test between CMOS and camera sig- nal processor IC Continued PMW-200/PMW-EX280...
  • Page 89 Startup must be com- matching check agnosis" pleted 0x21 ExpressCard ExpressCard power Non-installation "-6" is Startup must be com- switch ON/OFF control always returned. pleted 0x22 (SlotA) ExpressCard overcur- Non-installation "-6" is Startup must be com- rent detection always returned. pleted Continued PMW-200/PMW-EX280...
  • Page 90 1, 2 　 　 — 　 IC1700 on the DCP-56 board 　 　 put data and input data Error number of failed diagnosis is displayed as an error value. For error values, refer to "Error values of di- agnosis items ID 0x15". PMW-200/PMW-EX280...
  • Page 91 Path: Pin L1 → pin P7 Data: 0xaaaaaa00 Starting serial input channel: Channel 6 Starting serial output channel: Channel 6 Path: Pin N11 → pin P7 Data: sine wave (1 kHz) Starting serial input channel: Channel 0 Starting serial output channel: Channel 0 Continued PMW-200/PMW-EX280...
  • Page 92 0x08 　 -1: Error 1, 2 　 Normal end "0" is always re- C communication test (sub-micro- turned because there is no ap- computer of the viewfinder) plicable device in this unit. Continued 3-10 PMW-200/PMW-EX280...
  • Page 93 Type1/2 Note 0x80 Video signal line test -1: Test pattern check error 1, 2 Video signal line test between the camera signal processor IC and the baseband processing IC. Monitor output images will be distorted during the test. 3-11 PMW-200/PMW-EX280...
  • Page 94 Diagnosis between the display block and the media block tests the following contents. Diagnosis Error value Type1/2 Note 0x91 　 Video signal line communication test -1: Test pattern check error 1, 2 　 — in playback direction (Direction from MEDIA to DIS- PLAY) 3-12 PMW-200/PMW-EX280...

  • Page 95: Error Code List

    Repair theDPR-343 board or replace it. E-17001 　 The media ID data in the EEPROM is abnormal Rewrite the media ID data in the EEPROM. For details, contact your local Sony Sales Office/Serv- ice Center. E-17002 The image processor block does not start Repair the DCP-56 board or replace it.

  • Page 97: Electrical Alignment

    4-1-1. Notes on Adjustments • When making electrical adjustment or self-diagnosis, contact your local Sony Sales Office/Service Center. • When adjusting this unit, use an AC adapter or a fully-charged battery pack. • When disconnecting the AC adapter or the battery pack after adjustment, turn off the power switch and wait for at least 10 seconds.

  • Page 98: Maintenance Menu

    Do not change the Black Shading correction values from ±0 unless it is necessary. Setting It can be set to enable or disable the Black Shading correction function. This function is enabled automatically after the power is turned on. PMW-200/PMW-EX280...

  • Page 99: White Shading Adjustment

    • Use a full-white pattern having uniform brightness for the White Shading adjustment. • If a full-white pattern having uniform brightness is not available, do not perform the G-channel White Shading adjustment, but perform adjustment in the way of matching the R-channel waveform and the B-channel waveform with the G-channel waveform. PMW-200/PMW-EX280...

  • Page 100: Flare Adjustment

    Adjust H Saw, H Para, V Saw, and V Para for each of G-channel, B-channel, and R-channel until the waveform on the waveform monitor becomes flat. (H SAW) (H PARA) (V SAW) (V PARA) 4-2-5. Flare Adjustment The Flare Adjustment menu enables flare compensation for the respective channels of G-channel, B-channel and R- channel. PMW-200/PMW-EX280...

  • Page 101: Executing Auto Fb Adjust

    The result of Auto FB Adjust is saved. • When the Auto FB Adjust menu is selected, the Execute and Cancel choices appear. In addition, selecting Execute starts automatic adjustment of flange back. PMW-200/PMW-EX280...
  • Page 102 • Upgrade the firmware to the latest version. (Refer to “1-5. Firmware Upgrade”) • Prepare a star chart (reflective type) and set this unit at a distance of 3 meters from the star chart. Star chart (reflective type) PMW-200 • Set the camera as follows. Item Setting FOCUS RING...
  • Page 103 Set the lens iris to OPEN, set the zoom to TELE end, and adjust the focus. Move the zoom to WIDE end, and check that the lens stays in focus throughout the travel between TELE end to WIDE end. PMW-200/PMW-EX280...

  • Page 104: Rpn Correct Menu

    RPN point. • When the RPN correction point is moved to an already-registered correction point by the Cursor Next or Cursor Prev operation, the display automatically switches to the numeric value of the vertical position of the RPN point. PMW-200/PMW-EX280...

  • Page 105: Operating Cursor Next

    • The RPN data registered at the factory and the RPN data registered manually cannot be deleted by Reset. • When the Reset menu is selected, the Execute and Cancel choices appear. In addition, selecting Execute starts reset of RPN. RPN manual registration procedure Set Video Format to HD422 50/1080/59.94i. PMW-200/PMW-EX280...
  • Page 106 When the Record menu is attempted, if the RPN registration of a pixel fails at a specific address due to a problem with the small interval between the current and previous registered RPN spots, a message “NG : Adjacent Pixel” appears. 4-10 PMW-200/PMW-EX280...

  • Page 107: Spare Parts

    Therefore, specified parts should be used in the case 指定の部品を使ってください。 of replacement. 2. Standardization of Parts 2. 部品の共通化 Some repair parts supplied by Sony differ from those ソニーから供給する補修用部品は，セットに使われ used for the unit. These are because of parts common- ているものと異なることがあります。 ality and improvement.

  • Page 108: Exploded Views

    5-2. Exploded Views Overall 2.6 x 5 2.6 x 5 2.6 x 5 2.6 x 5 2.6 x 5 PMW-200/PMW-EX280...
  • Page 109 4-427-934-02 s BATTERY LID 4-427-935-02 s PANEL, BOTTOM 4-427-940-01 s COVER USER TAP 4-433-453-01 s SPACER, BOTTOM 4-446-349-01 s BRACKET, WIFI 4-446-827-01 s HOLDER, MICROPHONE 4-447-306-01 s CUSHION (B), BOTTOM 4-447307-01 s CUSHION (C), BOTTOM 7-627-556-58 s SCREW +P 2.6X5 PMW-200/PMW-EX280...
  • Page 110 4-428-408-01 s SPRING, HELICAL TORSION COIL 4-446-019-01 s SW INSULATING SHEET H 4-428-410-01 s SW INSULATING SHEET B 4-428-411-01 s SW INSULATING SHEET C 4-428-985-01 s COVER, AU VOLUME 4-446-018-01 s SHEET (H), SW CONDUCTIVITY 7-688-001-02 s W 2, SMALL PMW-200/PMW-EX280...
  • Page 111 3-056-233-21 s SCREW (M2), LOCK ACE, P2 3-080-206-21 s SCREW, TAPPING, P2 4-410-288-01 s BUTTON, REC 4-441-559-01 s CAP, WIFI USB 4-414-598-01 s TAPE (12X35) 1-759-071-11 s CORE, FERRITE 4-119-886-01 s TA;PE (13X50) 4-446-016-01 s TAPE AS (0720) 7-627-556-58 s SCREW +P2.6X5 PMW-200/PMW-EX280...
  • Page 112 3-080-206-21 s SCREW, TAPPING, P2 3-278-255-01 s TAPE (BT) 3-878-657-01 s TAPE 50 4-414-598-01 s TAPE (12X35) 4-428-300-01 s PLATE, AU HOLD 4-428-399-01 s SHEET (IN), WATERPROOF 4-435-865-01 s GASKET (G), MAIN 4-446-005-01 s GASKET MAIN L 4-447-332-01 s SHEET (J), WATERPROOF PMW-200/PMW-EX280...
  • Page 113 Front Panel Assembly Part No. SP Description A-1885-812-A s MOUNTED CIRCUIT BOARD, SW-1559 A-1885-984-A s MOUNTED CIRCUIT BOARD, SW-1573 X-2585-655-1 s PANEL SUB ASSY, FRONT 1-846-304-11 s CABLE, FLEXIBLE FLAT (6 CORE) 3-080-206-21 s SCREW, TAPPING, P2 PMW-200/PMW-EX280...
  • Page 114 4-428-368-01 s WASHER, BNC COAXIAL FIXED 4-428-375-01 s USB COVER 4-446-001-01 s TAPE (H), FRAME CONDUCTIVE 4-446-003-01 s TAPE (H), LENS CONDUCTIVE 4-446-004-01 s GASKET MAIN K 4-446-006-01 s GASKET MAIN M 4-446-014-01 s TAPE AS (2040) 4-446-017-01 s TAPE (H), DCP CONDUCTIVE PMW-200/PMW-EX280...
  • Page 115 4-427-952-02 s RADIATION SHEET D 4-427-953-02 s RADIATION SHEET E 4-427-954-02 s RADIATION SHEET F 4-427-956-02 s RADIATION SHEET H 4-428-812-01 s GASKET (D), MAIN 4-433-496-01 s TAPE, FP CONDUCTIVE 3-278-255-01 s TAPE (BT) 4-119-886-01 s TAPE (13X50) 4-435-865-01 s GASKET (G), MAIN PMW-200/PMW-EX280...
  • Page 116 4-445-606-01 s SHEET, EVF HARNESS X-2584-442-1 s COVER ASSY, HINGE (FRONT) 1-480-298-11 s SWITCH BLOCK, CONTROL(GZ92000) 2-630-005-01 s SCREW(M2), NEW TRUSTER,P2 7-627-556-58 s SCREW +P2.6X5 3-056-233-21 s SCREW (M2), LOCK ACE, P2 3-061-234-01 s NUT (M6X0.5) 3-080-206-21 s SCREW, TAPPING, P2 5-10 PMW-200/PMW-EX280...
  • Page 117 2-630-005-01 s SCREW(M2), NEW TRUSTER, P2 4-428-166-01 s SCREEN, SPEAKER 3-069-286-03 s SHOE, ACCESSORY 3-080-203-51 s SCREW(M2), LOCK ACE, P2 (for 4-428-167-01 s HANDLE PMW-200) 3-056-233-21 s SCREW (M2), LOCK ACE, P2 4-432-184-01 s SCREW (M2), NEW TRUSTER, P2 (for 1-968-343-11 s HARNESS (DCP-KSW) PMW-EX280)
  • Page 118 4-428-130-01 s CABINET LCD 4-428-134-01 s RETAINER, PANEL 1-482-034-11 s CORE, FERRITE 3-878-657-01 s TAPE 50 4-429-227-01 s PLATE, LCD SHIELD 4-429-228-01 s PLATE, PANEL GROUND 3-278-255-01 s TAPE (BT) 4-435-866-01 s GASKET (H), MAIN 4-446-007-01 s GASKET MAIN N 5-12 PMW-200/PMW-EX280...
  • Page 119 1015 3-288-591-01 s SHEET, VF PROTECTION 1016 3-302-492-01 s SPRING, COMPRESSION 1017 3-963-822-12 s KNOB, LOCK 1018 4-164-856-01 s EYE CUP 1019 4-164-591-02 s CABINET EVF 1020 4-164-592-01 s GUIDE LOCK LEVER 1021 4-445-605-01 s PLATE, EVF GROUND 5-13 PMW-200/PMW-EX280...
  • Page 120 3-694-181-03 s TYPE1, AROCK PRECISION +P2.6X5 1111 3-278-255-01 s TAPE (BT) 1112 4-427-941-01 s CUSHION CONNECTOR (MAIN) 1113 4-427-949-02 s RADIATION SHEET A 1114 4-427-950-02 s RADIATION SHEET B 1115 4-427-951-02 s RADIATION SHEET C 1116 4-427-952-02 s RADIATION SHEET D 5-14 PMW-200/PMW-EX280...
  • Page 121 4-427-942-01 s GASKET MAIN A 1217 4-427-943-01 s GASKET MAIN B 1218 4-430-771-01 s CN GUARD 1219 4-445-608-01 s TAP, ACCESSORY 1220 4-435-867-01 s GASKET (J), MAIN 1221 4-446-008-01 s GASKET MAIN P 1222 4-446-009-01 s GASKET MAIN Q 5-15 PMW-200/PMW-EX280...
  • Page 122 Lens Block Assembly 1301 Part No. SP Description 1301 A-1911-477-A s FRONT ASSEMBLY (RP) 5-16 PMW-200/PMW-EX280...

  • Page 123: Electrical Parts List

    HN-384 BOARD CN007 1-816-113-21 s CONNECTOR 15P CN2200 1-764-243-31 o CONNECTOR (COAXIAL) Ref. No. CN2201 1-778-646-31 s CONNECTOR, FFC/FPC(ZIF) ST 10P or Q'ty Part No. SP Description THP100 1-771-845-21 s THERMISTOR, POSITIVE A-1864-828-A s MOUNTED CIRCUIT BOARD, HN-384 5-17 PMW-200/PMW-EX280...
  • Page 124 IF-1182 BOARD PSW-97 BOARD Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No. SP Description A-1864-829-A s MOUNTED CIRCUIT BOARD, IF-1182 A-1864-816-A s MOUNTED CIRCUIT BOARD, PSW-97 CN103 1-778-645-31 s CONNECTOR, FFC/FPC(ZIF) AN 10P 5-18 PMW-200/PMW-EX280...
  • Page 125 1-815-597-31 s CONNECTOR, FFC/FPC (ZIF) AN 6P CN104 1-794-375-21 s PIN, CONNECTOR 2P A-1885-812-A s MOUNTED CIRCUIT BOARD, SW-1559 CN105 1-818-210-21 s PIN, CONNECTOR 2P CN104 1-818-210-21 s PIN, CONNECTOR 2P CN301 1-821-530-12 s CONNECTOR, EX CARD (HOST) 5-19 PMW-200/PMW-EX280...
  • Page 126 VR-350 BOARD Ref. No. or Q'ty Part No. SP Description A-1890-568-A s MOUNTED CIRCUIT BOARD, VR-350 CN101 1-778-645-31 s CONNECTOR, FFC/FPC(ZIF) AN 10P 5-20 PMW-200/PMW-EX280...

  • Page 127: Supplied Accessories

    4-268-461-05 s CD-ROM (UTILITY SOFTWARE) 4-425-716-03 s MANUAL, INSTRUCTION (Japanese) (For PMW-200 (J)) 4-425-716-13 s MANUAL, INSTRUCTION (English) (For PMW-200 (UC), (CE), (E)) 4-425-716-21 s MANUAL, INSTRUCTION (Chinese) (For PMW-EX280 (CN)) 4-425-718-03 s CD-ROM (INSTRUCTION MANUAL) (For PMW-200 (UC), (CE), (E))

  • Page 129: Block Diagrams

    SUPPLY (CROWN) S101 IC1002 SLOT B CN100 CN101 POWER CN100 CN101 (EXPRESS CARD) DDR2 CN101 CN100 DC IN SW-1578 IC2101 IC1101 CN2200 USB(Service) SEL/SET IC2007 FLASH SYSTEM FLASH CONTROL IC2006 (MELON) SDRAM IC2201 EPROM Overall CN2400 CN2500 A/V MULTI PMW-200/PMW-EX280...

  • Page 131: Schematic Diagrams

    FLEXIBLE FLAT CABLE CN102 CN105 CN100 HARNESS S100 SLOT OPERATION PANEL OF INSIDE SW-1575 CN101 CN100 SW-1578 CH-1 CH-2 CN100 SW-1579 SW-1577 EN100 AUDIO LEVEL S101 S100 S100 S101 Frame Wiring MENU CANCEL L/M/H B/A/PRST GAIN WHITE BAL SEL/SET PMW-200/PMW-EX280...
  • Page 134 PMW-200 (J) PMW-200 (UC) PMW-200 (CE) PMW-200 (E) Printed in Japan Sony Corporation PMW-EX280 (CN) J, E 2012. 8 08 9-968-962-02 © 2012...

This manual is also suitable for:

Pmw-ex280

Table of Contents