Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Table of Contents
Related Manuals for Toshiba RAS-B10U2FVG-E
Summary of Contents for Toshiba RAS-B10U2FVG-E
- Page 1 INSTALLATION MANUAL AIR CONDITIONER (SPLIT TYPE) Indoor unit RAS-B10, 13, 18U2FVG-E 1112151199...
-
Page 2: Table Of Contents
CONTENTS PRECAUTIONS FOR SAFETY ..............................1 ACCESSORY PARTS .................................. 5 INSTALLATION DIAGRAM OF INDOOR UNIT .......................... 6 Optional Installation Parts ................................. 6 INDOOR UNIT ....................................7 Installation Place ..................................7 Cutting a Hole and Mounting Installation Plate ......................... 7 ... -
Page 3: Precautions For Safety
PRECAUTIONS FOR SAFETY PRECAUTIONS FOR SAFETY Read the precautions in this manual carefully before This appliance is filled with R32. operating the unit. • Before installation, please read these precautions for safety carefully. • Be sure to follow the precautions provided here to avoid safety risks. The symbols and their meanings are shown below. - Page 4 • TO PREVENT OVERHEATING THE INDOOR UNIT AND CAUSING A FIRE HAZARD, PLACE THE UNIT WELL AWAY (MORE THAN 2 M) FROM HEAT SOURCES SUCH AS RADIATORS, HEATERS, FURNACE, STOVES, ETC. • WHEN MOVING THE AIR CONDITIONER FOR INSTALLING IT IN ANOTHER PLACE AGAIN, BE VERY CAREFUL NOT TO GET THE SPECIFIED REFRIGERANT (R32) WITH ANY OTHER GASEOUS BODY INTO THE REFRIGERATION CYCLE.
- Page 5 • For R32 model, use pipes, fl are nut and tools which is specifi ed for R32 refrigerant. Using of existing (R22) piping, fl are nut and tools may cause abnormally high pressure in the refrigerant cycle (piping), and possibly result in explosion and injury.
- Page 6 REQUIREMENT OF REPORT TO THE LOCAL POWER SUPPLIER Please make absolutely sure that the installation of this appliance is reported to the local power supplier before installation. If you experience any problems or if the installation is not accepted by the supplier, the service agency will take adequate countermeasures.
-
Page 7: Accessory Parts
ACCESSORY PARTS ACCESSORY PARTS ACCESSORY AND INSTALLATION PARTS Parts name (Q’ty) Parts name (Q’ty) Installation plate* x 1 Wireless remote control* x 1 Battery x 2 Remote control holder* x 1 Filter** Filter** Mounting screw** ø4 x 25 s x 8 Pan head wood screw ø3.1 x 16 s x 2 Insulation sheet x 1 (for some models only) Drain nipple*** x 1 (for heating model only) -
Page 8: Installation Diagram Of Indoor Unit
INSTALLATION DIAGRAM OF INDOOR UNIT INSTALLATION DIAGRAM OF INDOOR UNIT Do not allow the drain hose to get slack. Air fi lter Installation plate Cut the piping hole sloped slightly. 50 mm or more 50 mm or more Make sure to run the drain hose Filter sloped downward. -
Page 9: Indoor Unit
INDOOR UNIT INDOOR UNIT Mounting the installation plate and screw position Installation Place (Unit : mm) • A place which provides the spaces around the indoor unit as shown in the diagram. • A place where there are no obstacles near the air inlet and outlet. •... -
Page 10: How To Install Indoor Unit
2. Put water in the drain pan and make sure that the water is drained out of How to Install Indoor Unit doors. 3. When connecting extension drain hose, insulate the connecting part of extension drain hose with shield pipe. 1. -
Page 11: Concealed Installation
Mounting directly on the fl oor. 1) Fix the leg of indoor unit on the fl oor with 2 mounting screws. 2) Fix the upper part of indoor unit on the wall with 4 mounting screws. For prevent dewfall (Floor installation) Wall burying mode Slit 2. -
Page 12: Others
(Front view) 70 or more (Side view) 800 or more Opening for receiver Opening for receiver 20 to 30 Partition board Partition board 50 or more 50 or more OTHERS OTHERS Note : 1. Repeat above step to reset Remote Control to be A. Gas Leak Test 2. - Page 13 1112151199...