Table of Contents
Advertisement
Available languages
Available languages
Trouble shooting
en
Regenerating the activated charcoal filter
The activated charcoal filters must be regenerated or
replaced regularly in order to ensure that odours
continue to be eliminated effectively. The saturation
indicator on your appliance will tell you how frequently
this needs to be done.
The activated charcoal filters should be regenerated or
replaced at least every 2 months.
:
Warning – Risk of fire!
Non-regenerable activated charcoal filters may catch
fire in the oven. Never try to regenerate non-regenerable
activated charcoal filters. Only regenerate regenerable
activated charcoal filters.
Regenerable activated charcoal filters can be
Note:
regenerated up to ten times.
Odours may develop when regenerating the
Note:
activated charcoal filter. Make sure that the room is well
ventilated and open a window if required.
Regenerated air recirculation filters may be
Note:
damaged if they fall or are dropped. The damage is not
always visible from the outside. Dispose of and replace
down any regenerated air recirculation filters that fall or
are dropped.
Caution!
Risk of damage due to ingress of moisture into the
activated charcoal filter. Never clean activated charcoal
filters in the dishwasher or with a wet cloth.
If the activated charcoal filter can no longer be
1.
regenerated, order a new regenerable activated
charcoal filter and use it in place of the old one.
Heat the activated charcoal filter for 1 hour at
2.
100 °C in the oven (preheated) using air
recirculation mode.
Allow the activated charcoal filter to cool down.
3.
Fitting the activated charcoal filter
Place the activated charcoal filter onto the metal
1.
grease filter.
Fix the activated charcoal filter to the grille.
2.
Resetting the saturation displays
Once you have cleaned or replaced the relevant filters,
reset the saturation indicator to stop the symbols from
flashing.
Make sure that the extractor hood has been
1.
switched on.
Touch and hold
for approx. 3 seconds.
!
2.
This resets the saturation indicators.
22
3Trouble shooting
M alfunctions often have simple explanations. Please
T r o u b l e s h o o t i n g
read the following notes before calling the after-sales
service.
:
Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
LED lights
Defective LED lights must only be replaced by the
manufacturer, their customer service department or a
licensed technician (electrician).
What to do if water gets in
If water gets in to the appliance during cooking or
cleaning, proceed as follows:
Switch off the appliance.
1.
Open the floor cupboard and mop up leaking water.
2.
Leave the appliance switched off for 24 hours.
3.
After this time, the appliance can be used again
without restrictions.
Malfunction table
Problem
Possible cause
The appliance
The plug is not
does not work
plugged in.
Power cut
Faulty fuse
Appliance does
Filter cover not
not switch on.
closed.
The appliance
The circuit breaker in
does not extend
the electrical box is
or retract.
defective.
The button illumi-
The control unit is
nation does not
faulty.
work.
The lighting does
The LED lights are
not work.
defective.
The grease filter or
!
or ? will flash
the activated charcoal
on the display.
filter is saturated.
--------
Solution
Connect the appliance to
the electricity supply
Check whether other
kitchen appliances are
working
Check in the fuse box to
make sure that the fuse
for the appliance is OK
Close the filter cover fully.
Call the after-sales ser-
vice.
Call the aftersales ser-
vice.
Call the after-sales ser-
vice.
Clean the filter or replace
the activated charcoal fil-
ter. ~ "Cleaning and
maintenance" on page 20
- Quick Links:
- Sättigungsanzeigen Zurücksetzen
Hide quick links:
Advertisement
Chapters
Table of Contents
