Advertisement
Available languages
Available languages
Quick Links
DS200 Key Chain Remote Control
WARNING: Read and understand all instructions and
warnings for this product. In addition, read and follow all
instructions and warnings provided with the DS100 JobSite
Security Portable Alarm System.
CAUTION: DANGER OF EXPLOSION, INJURY OR FIRE.
Carefully follow all instructions and warnings on the battery label and
package.
• Never use a damaged or worn out battery.
• Discharged batteries should be replaced only with type CR-2 3.0
Volt Lithium batteries.
• Do not use re-chargeable batteries or attempt to charge batteries.
• Carefully remove the old, discharged battery.
• Do not attempt to open.
• Do not peel the label from the battery.
• Never dispose of a battery in a fire.
• Dispose of used batteries in accordance with local regulations.
• Recycle batteries.
• Always insert batteries correctly with regard to polarity (+ and -)
marked on the battery and the equipment.
• When installing the battery, do not use excessive force. If the bat-
tery does not fit, check to make sure that it matches the polarity
markings.
• Never expose the battery terminals to any other metal object. This
can short circuit the battery.
• Avoid exposure to temperature extremes.
• When not in use, store the battery in a cool, dark, dry place.
• Keep batteries out of reach of children.
CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR
FAILURE. Do not use near water. Damage to the equipment may
occur. Equipment shall not be exposed to liquids.
FCC REGULATORY STATEMENT (FCC: HCQ3B6ETRT2M)
• This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) the device must accept any
interference received, including interference that may cause unde-
sired operation.
INDUSTRY CANADA (IC: 2309A-ETRT2M)
• NOTICE: This equipment meets the applicable Industry Canada
Terminal Equipment Technical Specifications. This is confirmed
by the registration number. The abbreviation, IC, before the reg-
istration number signifies that registration was performed based
on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that Industry
Canada approved the equipment.
Components (Fig. 1, 2)
A. Antenna
E. Battery
B. LED
F. Reset Button
C. Lock Button
G. Carabiner
D. Unlock Button
Product Function
The DS200 Key Chain Remote Control is used for arming or disarming
the system from a range of up to 2000' (610 m).
Once activated, this device will work exclusively with the assigned
DS100 JobSite Security Portable Alarm System.
• The remote uses 900 MHz spread spectrum communication to
provide superior range and robustness.
• The DS200 has an LED feedback light which notifies the user
when a signal is being sent to the Base Unit.
SITELOCK LLC, 626 Hanover Pike, Hampstead, MD 21074
FIG. 1
B
D
C
G
CAUTION: POTENTIAL EQUIPMENT MALFUNCTION
OR FAILURE. Do not touch the electronic components
inside the device, except the reset button and battery.
•
LOCK (C) – press and release to arm the system.
•
UNLOCK (D) – press and release to disarm the system.
• The DS200 remote uses a CR-2 3.0V Lithium battery (E) for long
life.
• The reset button (F) allows the Key Chain Remote Control to be
registered to any D
set up.
• A convenient carabiner clip (G) is included for versatility.
NOTE: Metal objects blocking radio frequency (RF) transmission can
affect the range of the Key Chain Remote.
Prevention of False Alarms
The majority of alarms that occur are false. These situations happen
every day due to user error, incorrect installation or improper mainte-
nance of the system. False alarms will limit the responsiveness to the
system, and become a general inconvenience. As the number of false
alarms increases, authorities have become less apt to respond to
alarm systems due to this problem. Many of these situations can be
avoided by following some very simple practices.
• Ensure all users are properly trained on the operation of the
system.
• Always turn off the system with the Key Chain Remote Control
before entering protected area.
• Lock all protected doors, windows or any other asset attached to
a sensor.
• Check that motion detectors are not obstructed. Do not allow
sources of heat or sound in range of the motion or vibration sen-
sors.
• Check that premises are cleared and assets secured before setting
the system.
• Turn off all noise sources – radios, compressors, generators,
heavy equipment, etc.
• Know how to cancel an alarm or turn off the system before
activating.
• If a false alarm is tripped notify customer service immediately.
• Test the system on a monthly basis to ensure proper functioning
• Check cellular signal, power supply, and that sensors are secured
on a daily basis.
Recommended Uses
The DS200 Key Chain Remote Control is useful for arming and
disarming the system without typing a user code on the keypad. Up
to 6 Key Chain Remotes can be added to the system.
Installing & Changing Battery
The DS200 Key Chain Remote Control requires a non-rechargeable
CR-2 3.0 Volt Lithium battery.
CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR
FAILURE. Do not touch the electronic components inside the
device, except the reset button and battery.
(SEP04)
Form No. 626133-00
FIG. 2
A
F
E
WALT JobSite Security system with easy
E
DS200
Copyright © 2004 D
FIG. 3
WALT
E
Advertisement
Related Manuals for DeWalt DS200
Summary of Contents for DeWalt DS200
-
Page 1: Product Function
UNLOCK (D) – press and release to disarm the system. • Never dispose of a battery in a fire. • The DS200 remote uses a CR-2 3.0V Lithium battery (E) for long • Dispose of used batteries in accordance with local regulations. - Page 2 Instruction Manual for more details on registering a device during the defects due to faulty materials or workmanship. For warranty repair initial setup. information, visit www.dewalt.com or call 1-800-4-D WALT NOTE: The system must be disarmed prior to any programming (1-800-433-9258).
- Page 3 (se reporter à la supérieures. section Enregistrement du dispositif), remettre le couvercle. • La DS200 comporte un voyant DEL de réponse pour avertir l’util- POUR CHANGER LA PILE isateur qu’un signal a été envoyé à la base.
- Page 4 (fig. 3). 8. À la demande REINIT DISP sur l’écran ACL, pousser puis relâch- Control remoto de llavero DS200 er le bouton de réinitialisation (F) sur le panneau de contrôle. L’écran indiquera que le dispositif a été enregistré.
- Page 5 (+ y -) de la pila y el equipo. No use demasiada fuerza. Si la • El control remoto del DS200 utiliza una pila de litio de 3,0 voltios pila no entra, verifique que las marcas de polaridad correspondan tipo CR-2 (E) para una mayor duración.
- Page 6 Repararemos, sin costo, cualquier defecto debido a fallas en materi- ales o mano de obra. Para mayor información sobre reparaciones bajo garantía, visite www.dewalt.com o llame al 1-800-4-D WALT...