hit counter script
Cisco TelePresence ISDN GW MSE 8321 Getting Started Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Gateway
  5. TelePresence ISDN GW MSE 8321
  6. Getting started manual
Cisco TelePresence ISDN GW MSE 8321 Getting Started Manual

Cisco TelePresence ISDN GW MSE 8321 Getting Started Manual

Hide thumbs Also See for TelePresence ISDN GW MSE 8321:
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco TelePresence
ISDN GW MSE 8321
Getting Started Guide
61-0020-06

Advertisement

Table of Contents
loading

Related Manuals for Cisco TelePresence ISDN GW MSE 8321

Summary of Contents for Cisco TelePresence ISDN GW MSE 8321

  • Page 1 Cisco TelePresence ISDN GW MSE 8321 Getting Started Guide 61-0020-06...

  • Page 2: Table Of Contents

    Contents General information ........................ 3 About the Cisco TelePresence ISDN GW MSE 8321 ........3 Port and LED location ....................3 LED behavior ........................ 4 Installing the ISDN GW MSE 8321 ..................6 Step one: Install the ISDN GW MSE 8321 into the MSE 8000 chassis ..6 Connecting the ISDN GW MSE 8321 ..................

  • Page 3: General Information

    General information About the Cisco TelePresence ISDN GW MSE 8321 The Cisco TelePresence ISDN GW MSE 8321 (ISDN GW MSE 8321) is a high performance video gateway which enables ISDN network connectivity for the Cisco TelePresence IP-based video infrastructure products as well as IP-based endpoints.

  • Page 4: Led Behavior

    General information LED behavior Table 1 describes the behavior of the LEDs on the device. Table 1: ISDN GW MSE 8321 LED behavior Color Indicates Compact Flash Flashing One of: Activity green The device is booting  A configuration change has been made ...
  • Page 5 General information Table 1: ISDN GW MSE 8321 LED behavior (continued) Color Indicates Ethernet Port Status, for each Ethernet port: Green The link has been negotiated as a full-duplex link Green Packets are being transmitted on this port Link Green The speed of the link from this port, which is either 10, 100, or 1000 Mbps Power...

  • Page 6: Installing The Isdn Gw Mse 8321

    You must install either a blade or a blanking blade in each of the ten positions in the chassis. The Cisco TelePresence Supervisor MSE 8050 (Supervisor) must be installed into slot 1 of the MSE 8000 chassis. Remove the blade or blanking blade from the slot into which you are going to install the ISDN GW MSE 8321: Using a No.1 Phillips screwdriver, loosen the screws in the retaining latches...
  • Page 7 Installing the ISDN GW MSE 8321 Slide the ISDN GW MSE 8321 into the blade slot (as shown in Figure 2) until it stops. Simultaneously close both retaining latches on the blade (thereby engaging the connectors at the rear of the blade) to secure it in the chassis as shown in Figure 3.
  • Page 8 Installing the ISDN GW MSE 8321 Figure 3: Closing the retaining latches on the front of a blade...

  • Page 9: Connecting The Isdn Gw Mse 8321

    If your network provider has not terminated all of your incoming ISDN PRI lines with an NTU/CSU, Cisco recommends that you install a suitably approved CSU to protect the ISDN GW MSE 8321 from damage by surges on your ISDN PRI lines.

  • Page 10: Initial Configuration

    To establish a 1000 Mbps connection, both ends of the link must be configured as auto-sensing. To configure Ethernet Port A, log in to the Cisco TelePresence Supervisor MSE 8050 (Supervisor) web interface and go to . For more information Hardware >...

  • Page 11: Configuring The Isdn Gw Mse 8321

    Users admin Step two: Allocate port licences Port licenses must be allocated to the ISDN GW MSE 8321 from the Cisco TelePresence Supervisor MSE 8050 (Supervisor). To do this, go to the Port licenses page in the Supervisor web interface. For assistance see the Supervisor online help topic “Allocating port licenses to blades”.

  • Page 12: Step Six: Configure The Dial Plan

    Configuring the ISDN GW MSE 8321 Step six: Configure the dial plan By default the ISDN GW MSE 8321 rejects all calls. To enable calling with the ISDN GW MSE 8321 you must configure a dial plan with at least one dial plan rule for each direction in which you want calls to be accepted (IP to ISDN and/or ISDN to IP).

  • Page 13: Troubleshooting And Technical Support Information

    Make sure that you are running the most up-to-date software.  Get help from the Cisco Technical Support team.  Make sure you have the following information ready before raising a case: Identifying information for your product, such as model number, firmware ...

  • Page 14: Pin Outs

    Pin outs Pin outs The pin numbering for the PRI ports on the ISDN GW MSE 8321 is shown in Figure 4. The pin assignments for the PRI ports are shown in Table 2: Table 2: Pin assignments for PRI ports Pin number Signal Receive -...

  • Page 15: Disclaimers And Notices

    THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. www.cisco.com/go/ and other countries. A listing of Cisco's trademarks can be found at trademarks .

Table of Contents