LD ON mode in the test mode oscillates with the laser forcibly. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗: See page 28. PD-30-K...
11.3 OPERATION and REMOCON PCB ASSYS (for PD-30) .................... 74 11.4 OPERATION, OPERATION2 and REMOCON PCB ASSYS (for PD-10) ..............75 11.5 POWER and POWER 2 PCB ASSYS ........................76 11.6 DISPLAY, POWER SW and LED PCB ASSYS......................78 12. PCB PARTS LIST ................................80 PD-30-K...
Soldering time: Within 3 seconds Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pickup Unit to prevent the Flux smoke from it. Pickup PCB Soldering short land Short circuit using a soldering iron. Fig. 1 PD-30-K...
• Specifications and the design are subject topossible modifications without notice, due to improvements. • Corporation and product names mentioned herein are trademarks or registered trademarks of the respective corporations. Warranty card Operating Instructions (PD-30, PD-10-K, PD-10-S: J1190171A) (PD-10: J1180401A) PD-30-K...
Cleaning Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools. Position to be cleaned Name Part No. Remarks Pickup lens Cleaning liquied GEM1004 Refer to "7. DISASSEMBLY". Cleaning paper GED-008 PD-30-K...
Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. LIST OF ASSEMBLIES PD-30-K PD-30-S PD-10-K PD-10-S...
(PD-10-K, PD-10-S: A11801A240) (PD-10: A11802A240) PD-30 ONLY POWER SW PCB ASSY (A11901A320) PD-10 ONLY OPERATION2 PCB ASSY REMOCON PCB ASSY OPERATION PCB ASSY (PD-30: A11901ADA0) (PD-10-K, PD-10-S: A11801ADA0) (PD-30: A11901A270) (PD-10: A11802ADA0) (PD-10: A11801A270) PD-30 ONLY LED PCB ASSY (A11901ADT0) PD-30-K...
Page 9
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. 1/8- MAIN PCB ASSY (PD-30: A11905AF40) (PD-10-K, PD-10-S: A11801AF40) (PD-10: A11804AF40) MECHA ASSY (A11902A650) DISPLAY PCB ASSY (PD-30: A11901ADP0) (PD-10-K, PD-10-S: A11801ADP0) (PD-10: A11802ADP0) PD-30-K...
Page 11
High Side SW 3A DC/DC(5V) IC654 IC651 AT+3.3V TPS2557DRB RT8293AHZS POWER SW PURE STANDBY VBUS 5V POWER SW401 OS7601 AUDIO CONNECTOR LED PCB ASSY POWER SW REMOCON CP652 OPERATION PCB ASSY PCB ASSY PCB ASSY PD-30 ONLY PD-30 ONLY PD-30-K...
CP2302. connected? Check the Q7002 and arround Is waveform of IC4001 circuits. pin 215 0.5 Vp-p? Check the IC3001 and arround Is the voltage of CP1701 circuits. pin 11 about 3.3 V? Replace the IC4001. Replace the MECHA Assy. PD-30-K...
Page 14
3.3 V? Q6603, IC3001. Is the voltage of IC6602 pin 7 Check the IC7301/IC7303 and Check the IC7301 and around about 0 V? around circuits. circuits. Check the V;15A, V-15A lines of Check the IC6601 and AUDIO POWER. around circuits. PD-30-K...
CAPACITOR 5.85 V COUNTER SELECT AND I LIMIT 4.9 V CURRENT RESET LIMIT STATE MACHINE CURRENT LIMIT COMPARATOR ENABLE JITTER CLOCK 1.0 V + V THERMAL DC MAX SHUTDOWN OSCILLATOR 1.0 V ENABLE (EN) LEADING EDGE BLANKING LATCH SOURCE PD-30-K...
Page 18
Spindle driver input No connection TRB_2 Connect to external transistor base VINTK Tracking driver input BIAS Bias input MUTE Mute control Notes: The indicated polarities for the output pins are means polarity to inputs. Always ensure that V PVCC PD-30-K...
Page 19
UART or Clock sync Output (Timer A) 3 line serial I/O Input (Timer B) 3line (3 channel) CRC operation circuit (CCITT system) (generation many clauses expression: M16C/60 series CPU core Memory Watch dog timer (15 bits) INTB DMAC (2 channel) multiplier PD-30-K...
Page 20
Output of the transfer clock plural terminal output function. C mode SDA0 - SDA2 Serial data input and output. (but the output of SDA2 is N channel open drain.) SCL0 - SCL2 Transfer clock input and output. (but the output of SCL2 is N channel open drain.) PD-30-K...
Page 21
RESET IC 2.9V DELAY TYPE • Block Diagram Vref • Pin Function Pin Name Function Output terminal. (Output "L" at the detection, and become the high impedance at the cancellation.) Power supply terminal. Ground terminal. No connection. External condenser connection terminal for delays. PD-30-K...
Page 23
DQ Power: Provide isolated power to DQs for improved noise immunity. (3.3 V ± 0.3 V) Supply DQ Ground: Provide isolated ground to DQs for improved noise immunity. (0 V) Supply Power Supply: +3.3 V ± 0.3 V Supply Ground PD-30-K...
Page 24
Byte/Word Mode • Block Diagram RY/BY DQ0-DQ15 (A-1) Block Protect Switches Erase Voltage Generator Input/Output Buffers State Control Program Voltage Generator Command Chip Enable Register Data Latch Output Enable Logic Y-Decoder Y-Gating Vcc Detector Timer X-Decoder Cell Matrix A0-A19 PD-30-K...
Page 27
Pull-up to VDD1 system power supply terminal (TEST PIN) TEST16 Pull-up to VDD1 system power supply terminal (TEST PIN) TEST17 Pull-up to VDD1 system power supply terminal (TEST PIN) DVSS − GND terminal TMODE Connect to GND (TEST PIN) DVDDIO − IO Power supply (VDD1) terminal PD-30-K...
CDs: OK with 7.6e-3 or less TEST MODE: OFF Note: Even if you intend to continuously use the unit after POWER displaying the error rate, be sure to turn the power off then back on. Service remote control unit (GGF1381) PD-30-K...
Page 29
R 2 3 2 0 R 2 3 1 7 W 9 12 Q 2 3 0 5 Q 2 3 0 4 C P 2 3 01 C P 2 3 02 C P 3 0 02 SIDE A PD-30-K...
Insert a thin minus screwdriver in a slit, and slide Rack loading of MECHA Assy in the arrow direction of the figure. If the Tray pops out a little, fully pull it out by hand. Thin minus screwdriver Slit Thin minus screwdriver Tray open Rack loading MECHA Assy (Bottom view) PD-30-K...
Page 31
(CP7301, 1801) (3) Release the two jumper wires. (4) Remove the two Holder PCBs. CP1801 CP7301 (5) Remove the AUDIO PCB Assy. (6) Remove the four screws. (810923070U) (7) Remove the Shield MAIN Assy. ×4 Shield MAIN Assy PD-30-K...
Page 32
If the cushion FFC is torn when the MECHA Assy is detached, replace it with a new one (800WRA0023). Cleaning Pickup lens Clean the pickup lenses when it is stained, using the following cleaning materials: Cleaning liquid : GEM1004 Cleaning paper: GED-008 PD-30-K...
Page 33
(1) Remove the six screws. (8109K30A0R) (2) Remove the two screws. (810923070U) (3) Unhook the two hooks. (4) Disconnect the one flexible cable and one MAIN PCBAssy connector. (CP3002, 6601) (5) Remove the Front panel Section. Front panel Section CP6601 CP3002 PD-30-K...
9 Version number of SUM CHECK is displayed as follows by unit display window. (Fig. 5) SUM.25E0 Fig. 5 a Turn off the unit. 8.2 DEFAULT SETTING IC4004 : IN6J0C04A0 Auto Power Off : Off CD/SACD : SACD Pure Audio : Off DIMMER : Off (100%) PD-30-K...
Screws adjacent to b mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION AAA/IEC R03 dry cell batteries x2 PD-30-K...
Page 37
792WHA0872 7 Package Front 792WHA0871 8 Gift Box See Contrast table (2) 9 Lightron Sheet 791WHA0151 (2) CONTRAST TABLE PD-30-K/PWSYXZT8, PD-30-S/PWSYXZT8, PD-10-K/PWSYXZT8, PD-10-S/PWSYXZT8 and PD-10/FXZT are constructed the same except for the following: PD-30-K PD-30-S PD-10-K PD-10-S PD-10 Mark Symbol and Description...
9.2 EXTERIOR SECTION for PD-30 for PD-10 OPERATION2 PCB Assy PD-30 only PD-30-K...
Page 39
Felt sheet (PD-30 only) Cleaning liquied : GEM1004 Cleaning paper : GED-008 PD-30 only Shild main Assy PD-10 only PD-10 only PD-30 only PD-30-K...
Page 40
See Contrast table (2) 41 • • • • • 42 • • • • • 43 Screw, Tap Tite (B) BR See Contrast table (2) 44 Screw, Tap Tite (B) 8109K3080S 45 Screw, Tap Tite (B) See Contrast table (2) PD-30-K...
Page 41
(2) CONTRAST TABLE PD-30-K/PWSYXZT8, PD-30-S/PWSYXZT8, PD-10-K/PWSYXZT8, PD-10-S/PWSYXZT8 and PD-10/FXZT are constructed the same except for the following: PD-30-K PD-30-S PD-10-K PD-10-S PD-10 Mark Symbol and Description /PWSYXZT8 /PWSYXZT8 /PWSYXZT8 /PWSYXZT8 /FXZT MAIN PCB Assy A11905AF40 A11901AF40 A11801AF40 A11801AF40 A11804AF40 AUDIO PCB Assy...
Page 47
LES PIECES REPAREES PAR UN ETANT DANGERUSES AN POINT DE VUE SECURITE VOLD+ VOSL- N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES. VOTK- VOFC- VOTK+ VOFC+ CAUTION SINCE THESE PARTS MARKED BY ARE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY. PD-30-K...
B1704 HCB1608KF-181T20 1608 SH1704 YQ-12 ATTENTION CAUTION LES PIECES REPAREES PAR UN ETANT SINCE THESE PARTS MAR DANGERUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,US N'UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST DANS LA NOMENCLATURE DES PIECES. PD-30-K...
Page 57
V+3 (1;2;3;4;5;6;7) 1/8-6/8 R1714 10K 1/16W TO SDRAM/FLASH 1/8-6/8 V+3 (1;2;3;4;5;6;7) MPEG +1.8V +3.3V D1710 D1711 V+1R8 RB056L-40 RB056L-40 B1706 HCB1608KF-181T20 1608 SINCE THESE PARTS MARKED BY ARE CAUTION:DIGITAL TRANSISTER CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY. PD-30-K...
Page 59
LES PIECES REPAREES PAR UN ETANT IC1711 DANGERUSES AN POINT DE VUE SECURITE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES. CAUTION SINCE THESE PARTS MARKED BY ARE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY. CAUTION:DIGITAL TRANSISTER PD-30-K...
LES PIECES REPAREES PAR UN ETANT DANGERUSES AN POINT DE VUE SECURITE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES. CAUTION SINCE THESE PARTS MARKED BY ARE CRITICAL FOR SAFETY,USE ONES W949 DESCRIBED IN PARTS LIST ONLY. CAUTION:DIGITAL TRANSISTER PD-30-K...
10.14 DISPLAY, POWER SW and LED PCB ASSYS DISPLAY PCB ASSY (PD-30: A11901ADP0) (PD-10-K, PD-10-S: A11801ADP0) (PD-10: A11802ADP0) PD-30 ONLY POWER SW PCB ASSY (A11901A320) CP655 LED PCB ASSY (A11901ADT0) CP653 CP654 G H I PD-30-K...
10.15 WAVEFORMS 20 nS/div 20 nS/div 20 nS/div 20 nS/div 200 uS/div 20 nS/div 20 nS/div 200 uS/div 20 nS/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. PD-30-K...
11.6 DISPLAY, POWER SW and LED PCB ASSYS SIDE A PD-30 ONLY DISPLAY PCB ASSY CP653 CP101 LED PCB ASSY POWER SW PCB ASSY 1.D_GND 2.KEY_D POWER SW401 SIDE B POWER SW PCB ASSY IC6001 LED PCB ASSY R600 CP101 DISPLAY PCB ASSY G H I PD-30-K...
Page 79
SIDE A CP3002 CP6001 SIDE B CP6001 R6003 PD-30-K...
Therefore, when replacing, be sure to use parts of identical designation. SCHEMATIC DIAGRAM and PCB CONNECTION DIAGRAM → PCB PARTS LIST → CN → S → JA → FU → none → none LIST OF ASSEMBLIES PD-30-K PD-30-S PD-10-K PD-10-S PD-10 Mark Symbol and Description /PWSYXZT8 /PWSYXZT8 /PWSYXZT8...
Page 81
Mark No. Description Part No. Mark No. Description Part No. PARTS LIST (PD-30-K) POWER PCB ASSY SEMICONDUCTORS MAIN PCB ASSY IC 501 ILDF0176P0 SEMICONDUCTORS IC 502 I1KJ9A431A IC 2301 I1UFV5888S IC 503 000220002W IC 3002 IE1F0291A0 Q 502 TC4T031980 IC 3003...