Note: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller. D-Link DCS-3110 Quick Install Guide...
CAT5 Ethernet cable. This port connectors provide the physical interface to send and receive supports the NWay protocol, allowing the digital signals to and from a variety of external devices. network camera to automatically detect or DC12V output : negotiate the transmission speed of the Support for external device (like IR light) network. RS485: The Ethernet port can also be used to power Port is designed for external pan/tilt/zoom devices. the camera by using a PoE switch. D-Link DCS-3110 Quick Install Guide...
Sensor The IR-Cut removable sensor will judge the light conditions and then switches from color to B/W accordingly. Built-in Microphone Compact Flash Card Slot CF card slot CompactFlash (CF) is a mass storage device format used in portable electronic devices. The CF card slot can be seen at the side of the network camera. Note: Ensure to remove the rubber strip before using it. D-Link DCS-3110 Quick Install Guide...
Note: The LED on the network camera will turn green, when you have a proper connection. The light might go on and off and your computer may show an intermittent loss of connectivity, this is normal until you have configured your Network Camera. D-Link DCS-3110 Quick Install Guide...
Page 6
Hardware Installation The package comes with a camera stand with a swivel ball screw head that can be attached to the Network Camera bottom socket cavity. Attach the camera stand to the Network Camera and station it for your application. There are holes located in the base of the camera stand allowing the camera to be mounted to the ceiling, or any wall securely. D-Link DCS-3110 Quick Install Guide...
Software Installation Turn on the computer and insert the D-Link DCS-3110 CD into the CD-ROM drive. The following step-by-step instructions displayed are shown when using Windows Vista operating system. The steps and screens are similar ® when using other Windows operating systems. ® Click Installation Wizard Click Next to continue. Click Next Click I Agree to accept the License Agreement. Click I Agree D-Link DCS-3110 Quick Install Guide...
Page 8
Software Installation To start the installation click Install. Note: The installation may take several minutes to complete. Click Install Click Finish to complete the installation. Click Finish D-Link DCS-3110 Quick Install Guide...
Page 9
The Installation Wizard will appear and show the MAC address of your DCS-3110 and an IP Address (which may or may not be correct depending on what you have your DCS-3110 connected to). If you have a DHCP server on your network, there will be a valid IP Address displayed here. Note: A DHCP server is a device that supplies the same IP address. Click Manual Setup Enter the admin ID and password. Note: The default Admin ID is admin with the password left blank. Click Next D-Link DCS-3110 Quick Install Guide...
Page 10
Check the Get IP by DHCP Server automatically box to obtain a new IP address every time the camera starts up. Click Next to continue. Click Next Select UPnP Port Forwarding if your router supports this function. If not, choose Manual to manually enter your port numbers. Click Next to continue. Click Next D-Link DCS-3110 Quick Install Guide...
Page 11
Configuration Click Next to continue. Click Next A window will pop up asking you if you want to access the DCS-3110 via mobile phone. Clicking Yes will set the video resolution to 176x144. Click Apply to apply the settings listed in the window to the device. Application may take a few minutes to process. Click Apply D-Link DCS-3110 Quick Install Guide...
Page 12
A window will pop up to confirm that the application was successfully configured. Click OK to continue. A new window will pop up displaying the links/addresses to access your device. Click Add to my favorite to save the address and then click Exit to complete the installation. Click Exit Double-click the DCS-3110 to launch the camera’s web configuration page. Note: Please refer to the user manual for more information. D-Link DCS-3110 Quick Install Guide...
Page 13
Configuration Enter admin as the default username and leave the password blank. Click OK to continue. This section shows your camera’s live video. You can control your settings using the buttons at the bottom. For more information on using the web configuration, please refer to the user manual. D-Link DCS-3110 Quick Install Guide...