LD ON mode in the test mode oscillates with the laser forcibly. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 23. DV-2022...
Flux smoke away from it. Pick Up PCB Note There are 4 solder pads. If the Short circuit using a top & bottom pads are shorted soldering iron. together, this solder must be removed for the DVD to operate. Fig. 1 DV-2022...
Page 5
When soldering or unsoldering, completely remove all of the solder from the pins or solder area, and be sure to heat the soldering points with the lead free solder until it melts sufficiently. Recommendations Recommended lead free solder composition is Sn-3.0Ag-0.5Cu. DV-2022...
Page 6
2. Press and hold the 'STOP' key on the front panel. 3. Simultaneously press and hold the POWER key on the front panel. 4. The 4 digit password has now been cleared. NOTE: The above procedure will reset ALL of the player's settings to the default factory state. DV-2022...
BD/DVD recorder, if burn quality is not recording unit, consisting of a complete set of data from good due to characteristics of the disc, scratches, dirt on lead-in to lead-out. the disc, dirt on the recorder’s lens, etc. DV-2022...
Page 9
• The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file. • The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10. DV-2022...
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools. Position to be cleaned Name Part No. Remarks Pickup leneses Cleaning liquid GEM1004 Refer to “9.3 DVD MECHA SECTION”. Cleaning paper GED-008 DV-2022...
DVD MECHA ASSY DVD MT PCB ASSY REAR JACK PCB ASSY POWER PCB ASSY OPERATION PCB ASSY LIST OF ASSEMBLIES Mark Symbol and Description DV-2022/YXZT5 DV-2020/YXZT5 1..DVD MT PCB ASSY A2P031A130 A2P006A130 1..OPERATION PCB ASSY A2P031A270 A2P006A270 1..REAR JACK PCB ASSY...
Page 13
SP1- SP1- SP1+ SP1+ M2601 DVD MT PCB ASSY(1/6-6/6) JQ24-35H390 (DV-2022/YXZT5 :A2P031A130) (DV-2020/YXZT5 :A2P006A130) DVD PCB PCB130 DMK137 • NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE WITH SAME TYPE AND RATINGS OF FUSE.
OPEN/CLOSE Is the voltage at pin 8 and Check P.CON 6V line of POWER BLOCK. 19 of IC2301 about DC6V ? Is the lose connection Check CP2302 connection to DECK . at CP2302 to DECK ? Change DVD LOADER. DV-2022...
Page 18
Is there a voltage (beam current) at Q2302 Check LOADER BLOCK. and Q2303? Is there a signal at pin 100 of IC4001? Check IC4001 and peripheral circuit. Is there video signal at Check J7302 and peripheral circuit. J7302. Change IC4001. DV-2022...
Page 19
NO ANALOG AUDIO ON PLAYBACK. Is there AUDIO signal at Check J7302and peripheral circuit. pins 1 and 7 of IC8003? Is there AUDIO signal at pins 2 and 6 of IC8003? Check at pins 114 and 116 of IC4001. Change IC8003. DV-2022...
Get Start up types AC ON Upgrade or start by user FL initialization FL initialization The opening picture appears [DVD IC] Accesses 64M SDRAM (Remaining part) Disc detection (Focus control) Spindle turn Read Disc information code Disc Identification The picture appear DV-2022...
Page 21
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT PCB Assy : IC4001) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT PCB Assy : IC4005) Block noise is generated during playback. DV-2022...
• After going into service mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the servicemode. • The SKIP key and the SCAN key are effective during the service mode. SERVICE MODE: OFF POWER GGF1381 Service remote control unit DV-2022...
• Press the [ESC] key of the remote control unit. 3 LD ON DVD : Press the [TEST] and [1] keys in order, and turn on the laser diode (650n). : Press the [TEST] and [4] keys in order, and turn on the laser diode (780n). DV-2022...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-2022...
Region confirmation mode (ESC + A.MON [Service remote control unit] + "1"-"8" [Service remote control unit] keys) After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-2022...
-2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-2022...
Pick Up Unit to keep the Flux smoke away from it. 5. When installing the DVD Deck, remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector. DV-2022...
Page 29
4. Remove the Traverse Ass'y. Loader Sub Ass'y Loader Sub Ass'y Pulley Motor Loading Motor Loading Motor PCB Ass'y Insulator (R) Screw Torque: 1.0 ± 0.3kgf cm (Screw (2)) Traverse Ass' y Fig. 2-3-A Fig. 2-2-A Screw Torque: 2.0 ± 0.3kgf cm DV-2022...
Page 30
2-5: CLAMPER ASS'Y (Refer to Fig. 2-5-A) the direction, it cannot Ass'y (1) 1. Unlock the Spring Clamper. 2. Remove the Clamper Check Hook Spring Clamper Check Position Clamper Check Position Frame Sub Ass'y Check Hook UnLock Loading Motor PCB Ass'y Fig. 2-3-E Fig. 2-5-A DV-2022...
Page 31
To Pick Up PCB Rack Feed Ass'y Gear Middle Reinforcement Plate Screw Torque: 1.3 0.3kgf cm (Screw (2)) Scre w Torque: 2.5 0.3kgf cm (Screw (1)) Scre w Torque: 1.0 0.3kgf cm (Screw (3)) Fig. 2-7-A Printing Surface Fold Fig. 2-8 DV-2022...
While the screen shown at left is being displayed, updating is in progress. DO NOT TURN OFF THE POWER DURING UPDATING. 4 Updating of the firmware is completed. When the screen with the Pioneer logo is displayed, updating is completed. The time required for updating is about 2 minutes. DV-2022...
Page 33
2 If updating of the firmware using the disc for updating failed • Was the disc for updating recognized properly? Check if the volume label of the disc is PIONEER. • Is playback of a disc other than the disc for updating possible? If playback of a test CD is also impossible, a reading section, such as PU, may be defective.
Screws adjacent to b mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION DV-2022...
Page 35
See Contrast table (2) 4 Package Pad 792WHAA457 5 Gift Box See Contrast table (2) (2) CONTRAST TABLE DV-2022/YXZT5 and DV-2020/YXZT5 are constructed the same except for the following: Mark No. Symbol and Description DV-2022/YXZT5 DV-2020/YXZT5 3 Remote Control Unit 076E0SH051...
9.2 EXTERIOR SECTION Refer to "9.3 DVD MECHA SECTION". DV-2022...
Page 37
14 Screw, TAP TITE(B) BK (3x6) 810923060S 15 Screw, TAP TITE(P) (2.6x8) 811022680U (2) CONTRAST TABLE DV-2022/YXZT5 and DV-2020/YXZT5 are constructed the same except for the following: Mark No. Symbol and Description DV-2022/YXZT5 DV-2020/YXZT5 1 DVD MT PCB ASSY A2P031A130 A2P006A130 >...
If the repair is needed, replace the DVD MECHA ASS'Y. Note: NAME PART NO. MARK Applying positions AA and AB for the grease are NOTE: displayed for this section. SANKOL (CFD-5007Z) GEM1092 Check if the correct grease is applied for each FLOIL (G-313Y) GEM1062 position. DV-2022...
Page 39
21 Gear, Middle 92P100202A 22 Gear, Motor 92P100203A 23 Insulator (R) 92P200028A 24 Screw, Tap Tite(P) PanWH5.4 (1.7x8) 92P700020A 25 Screw, Tap Tite(P) Pan WH8 (2x8) 92P700021A 26 Screw, Pan (1.7x2.3) 814011723U 27 Screw, T-Tite(B) Camera Pan (1.7x5.0) 813381750U DV-2022...
C4055 FROM POWER PORT 0.1 B AT+3.3V D_GND TP4001 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-2022...
Page 43
MEMORY/USB SCHEMATIC DIAGRAM (DVD MT PCB) DVD MT PCB ASSY(2/6) 16M SERIAL FLASH IC (DV-2022/YXZT5 :A2P031A130) IC4004 GD25Q16SCPR C4062 (DV-2020/YXZT5 :A2P006A130) SFLASH_CS 0.1 B R4043 R4047 33 1/16W 10K 1/16W SFLASH_CK TP4004 SFLASH_DI V+3V DV-2022 Only V+5V_USB USB_P_ON-H USB_P_ON-L USB_P_ON-H...
MOT_SPDL- C2311 CAUTION ATTENTION :SINCE THESE PARTS MARKED BY :LES PIECES REPAREES PAR UN ETANT CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DV-2022...
Page 45
OPIN VOTR- Vcc2 VOTR+ VOLD- VOSL+ DVD MT PCB ASSY(3/6) VOLD+ VOSL- (DV-2022/YXZT5 :A2P031A130) VOTK- VOFC- (DV-2020/YXZT5 :A2P006A130) VOTK+ VOFC+ NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER...
560P CH ASPDIF R8060 120K 1/16W R8059 8.2K 1/16W +-1% AUDIO_R AUDIO_L R8049 8.2K 1/16W +-1% R8048 JACK MUTE(H:ON) Q8014 120K 1/16W KTA1504S_Y_RTK XAMUTE(L:ON) Q8013 RT1N241C NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-2022...
10.5 DVD MT PCB ASSY (5/6) DVD MT PCB ASSY(5/6) (DV-2022/YXZT5 :A2P031A130) (DV-2020/YXZT5 :A2P006A130) TO AUDIO JACK V+12 AUDIO_R AUDIO_L C7303 FROM/TO MPEG/MICON/DSP R/CR VIDEO_DRIVER IC B/CB IC7301 NJW1351RB1(TE1) CVBS TXD/VSEL 1.95 3.44 RXD/SQ 3.24 3.09 C7302 W864 CVBS 0.55...
Page 49
CVBS AUDIO L V+12 AUDIO R R7303 CVBS_OUT 1/16W +-1% G/Y_OUT B/U_OUT R/V_OUT AUDIO OUT CVBS J7302_1 J8002 RCA-117-02 RCA-232-00-01 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE PCB130 DMK137 DV-2022...
GND(M) GND(M) ATTENTION CAUTION :LES PIECES REPAREES PAR UN ETANT :SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES DV-2022...
820 1/16W R8101 4.7K 1/16W PROTECT Q8104 2N7002K-RTK/P A_GND NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-2022...
VIDEO JACK 500 s 10 s 200mV 200mV 1.0V 200ns 1.0V AUDIO JACK 500 s 1.0V 500 s 1.0V 200ns 500mV NOTE : The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. DV-2022...
Connector Capacitor 1. The parts mounted on this PCB include all necessary parts for several destinations. SIDE A For further information for respective desti- nations, be sure to check with the sche- matic diagram. SIDE B P.C.Board Chip Part DV-2022...
Page 63
SIDE B SIDE B OPERATION PCB ASSY PAL/NTSC R655 R656 R658 R666 IC601 DEK229A CD601 POWER PCB ASSY LOARDING MOTORPCB ASSY BLACK YELLOW SW01 GREEN BROWN FEJ005A CD2301 WHITE DV-2022...
11.3 REAR JACK PCB ASSY SIDE A SIDE A REAR JACK PCB ASSY A30C5 NTSC/PAL W001 CP8103 DEK232A J8101 SIDE B SIDE B REAR JACK PCB ASSY DEK232A NTSC/PAL R8102 Q8102 D8104 Q8104 R8127 Q8105 R8114 R8115 R8103 R8118 DV-2022...
I1UFV5888S IC 4001 MT1389DE/J-L IC8K0389JD IC 4004 GD25Q16SCPR S2P001AF01 IC 4005 EM638165TS-6G(70NM) IG2J08165G IC 4006 RP131K121D5-TR I1ZF91K120 IC 4009 RP131K501D-TR (DV-2022) I1ZF9K5010 IC 4010 RP130N501D I1ZF9N5010 IC 7301 NJW1351RB1 (YXZT5 type) I5AF013510 IC 8003 AZ4558C IL4J045580 MISCELLANEOUS X 4001 CRYSTAL (27MHz)