Toro Reelmaster 3555 Series Installation Instructions Manual
Rear roller brush mvp kit, 22-inch cutting unit with 5-inch or 7-inch reel and universal groomer
Hide thumbs
Also See for Reelmaster 3555 Series:
- Operator's manual (24 pages) ,
- Installation instructions manual (16 pages)
Advertisement
Quick Links
Rear Roller Brush MVP Kit
Reelmaster
Unit with 5-inch or 7-inch Reel and Universal Groomer
Model No. 133-0153
Model No. 133-0154
This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
No parts required
Roller-brush assembly
90-degree grease fitting
Carriage bolt (Model 133-0153 only—only for
5-inch cutting units driven by hydraulic reel
motors)
Weight (Model 133-0153 only—only for 5-inch
cutting units driven by hydraulic reel motors)
Locknut (Model 133-0153 only—only for
5-inch cutting units driven by hydraulic reel
motors)
Weight—Part No. 132-0735-03 (sold
separately)
Carriage bolt (5/16 x 2 inch)—Part No. 3230-6
(sold separately)
Bolt (5/16 x 1/2 inch)—Part No. 322-1 (sold
separately)
Washer (5/16 inch)—Part No. 3256-23 (sold
separately)
Flange nut (5/16 inch)—Part No. 104-8300
(sold separately)
Retaining ring
Belt-cover/plate assembly
Bolt (5/16 x 5/8 inch)
No parts required
Drive pulley
Flange-head bolt (5/16 x 1/2 inch)
Belt
No parts required
High height-of-cut brush (optional)
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3555, 3575, 5010, and 5010-H Series 22-inch Cutting
Qty.
Determine the position of the roller brush and the reel
–
motor.
1
Install the roller-brush assembly.
1
2
1
Install the weight (Model 133-0153 only).
2
1
2
Install the additional weight parts needed for RM5010-H
2
5-inch and 7-inch, RM3575, RM5510, and RM5610.
2
2
1
1
Install the roller-brush plate.
2
–
Position the roller brush.
1
1
Install the drive pulley and the belt.
1
–
Complete the installation.
Install the high height-of-cut brush—for HOC greater than
—
2.5 cm (1 inch).
Register at www.Toro.com.
Form No. 3411-973 Rev B
Installation Instructions
Use
Original Instructions (EN)
All Rights Reserved *3411-973* B
Printed in the USA
Advertisement
Related Manuals for Toro Reelmaster 3555 Series
Summary of Contents for Toro Reelmaster 3555 Series
- Page 1 Complete the installation. Install the high height-of-cut brush—for HOC greater than — High height-of-cut brush (optional) 2.5 cm (1 inch). © 2019—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3411-973* B 8111 Lyndale Avenue South Printed in the USA...
- Page 2 Installing the Roller-Brush Note: Determine the left and right sides of the cutting unit from behind the cutting unit. Assembly Important: Use the Rear Roller Brush Kit only when cutting in the height-of-cut range of 6 to If the cutting units are installed on the traction 25 mm (1/4 to 1 inch).
- Page 3 Installing the Weight Note: Do not remove the bolts. Keep the flange locknuts for future assembly. Included in Kit 133-0153 Position the left or right roller-brush-assembly mounting brackets onto the roller-bracket bolts (5-inch Hydraulically Driven (Figure Cutting Units) Install the weight to the cutting unit as shown in Figure (parts included with brush kit Model 133-0153).
- Page 4 Installing the Additional Installing the Roller-Brush Weight Parts Not Included Plate in the Kit (5-inch Electrically Slide the excluder seal outward until the lip seals are in light contact with each bearing housing Driven Cutting Units; 7-inch (Figure Hydraulically or Electrically Driven Cutting Units) Install the weight parts to the cutting unit as shown in Figure...
- Page 5 g035896 Figure 9 1. Roller-brush housing 3. Bolts 2. Retaining ring 4. Roller-brush pivot plate (left-drive configuration shown) g035897 Figure 10 Align the roller-brush pivot plate as shown in Figure...
- Page 6 Positioning the Roller Apply 242 Loctite (blue) to the 2 bolts (5/16 x 1/2 inch) and use them to mount the brush plate to Brush the roller-brush-bearing housing (Figure Note: Torque the bolts to 20 to 26 N∙m (15 to Loosen the 2 bolts securing each 19 ft-lb).
- Page 7 Tighten the 2 bolts securing each roller-brush-bearing housing to the roller-brush mounting brackets. Installing the Drive Pulley and the Belt Restrain the reel for installation; Restraining the Reel for Installing Threaded Inserts (page 12). Install the drive pulley onto the groomer shaft (Figure 13).
-
Page 8: Completing The Installation
Push down on the idler pulley to ensure that the idler-pulley assembly pivots freely. Completing the Installation Check the alignment of the belt and pulleys; refer Checking the Pulley Alignment (page 10). Slide the belt cover onto the mounting bolts and secure the cover with 2 flange nuts (Figure 16). - Page 9 Installing the High Clamp the brush onto the shaft with the 2 J-bolts and nuts previously removed (Figure 20). Height-of-Cut Brush Important: Insert the threaded end of the (Optional) J-bolts through the outer holes of the brush shaft while hooking the curved ends of the J-bolts into the inner holes.
-
Page 10: Maintenance
Maintenance Adjusting the Pulley Alignment • Ensure that the brush is parallel to the roller with 1.5 mm (0.060 inch) clearance to light contact. The driven pulley (at the roller-brush shaft) can move in or out (Figure 22). • Grease the fittings every 50 hours and after every washing. - Page 11 g193168 Figure 23 1. Locknut 4. Spacer 2. Driven pulley 5. Brush shaft flats 3. Washer—0.8 mm (0.032 inch) thick While holding the flats of the roller-brush shaft, secure the driven pulley on the shaft with the g020390 Figure 25 flange nut (3/8–16) previously removed.
- Page 12 Restraining the Reel for Installing back of the cutting reel, closest to the side of the cutting unit that you will be torquing (Figure 26). Threaded Inserts Place the pry bar against the weld side of the Insert a long-handled pry bar (recommended reel support plate (Figure 26).
- Page 13 Notes:...
- Page 14 Notes:...
- Page 15 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.