Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMpORTANT: REAd ThESE INSTRUCTIONS CAREFULLY. NOTE ThE SAFE OPERATIONAL REQUIREMENTS, WARNINGS ANd CAUTIONS. USE
ThIS JACK CORRECTLY ANd WITh CARE FOR ThE PURPOSE FOR WhICh IT IS INTENdEd. FAILURE TO dO SO MAY CAUSE dAMAGE ANd/OR
PERSONAL INJURY ANd WILL INVALIdATE ThE WARRANTY. RETAIN ThESE INSTRUCTIONS FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure all preliminary checks are carefully carried out before use of jack. Immediately repair or replace damaged parts
(use authorised service agent). Ensure use of genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Use jack on level and solid ground, preferably concrete. Ensure the floor over which the jack will be transported is swept clean.
DANGER! DO NOT use on tarmacadam, or any other soft surface as jack may sink or topple. Serious personal or fatal injury may result.
DANGER! If jack tips or leans STOp whAT yOUR ARE DOING. MOVE QUICKLy TO A SAFE DISTANCE. DO NOT TRy TO hOLD OR
STEADy JACK. Serious or fatal injury may result.
Use jack in a suitable workarea , keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
Before use ensure the gearbox weight and size does not exceed the capacity of the jack.
Ensure the vehicle is raised and stabilised at the correct height before attempting to move the jack under the vehicle.
Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery. Contain and/or tie back long hair.
WARNING! Ensure load is placed level and centrally on jack saddle and load is fixed in place before attempting to lift, lower, or transport.
The lowering speed will vary according to the weight of the load and the release valve setting.
Ensure the jack saddle is fully lowered and is clean, dry and oil free before attempting to move the jack with or without a load.
Diligence is required in ensuring that you continually monitor any operation until completed.
WARNING! DO NOT operate jack if any parts are damaged or missing.
DO NOT exceed the rated capacity of the jack.
DO NOT allow untrained persons to operate the jack.
DO NOT place any part of your body within or under the jack during use.
DO NOT raise or lower vehicle lifting platform whilst the transmission jack is being used.
DO NOT transport the jack, with or without a load, with the saddle in the raised position.
DO NOT get jack wet or use in damp or wet locations or areas where there is condensation.
DO NOT operate the jack when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT lift or support vehicles with jack and do not use jack as a load sustaining device.
DO NOT use jack for any purpose other than removal, transportation, installation of transmissions.
DO NOT move jack without suitable restraint on the load.
DO NOT make any modifications to the jack, and DO NOT adjust or tamper with safety valve.
DO NOT remove any labels from the jack. If labels are damaged or unclear replace them.
DO NOT use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil only.
Use a qualified person to lubricate and maintain the jack.
Before storing in safe area, ensure all parts are clean, free of grease and oil (especially saddle). Lower
saddle to the lowest position.
wARNING: The warnings, cautions and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood that common
sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
2.
SPECIFICATIONS
1.25 ton model with heavy-duty construction and foot-pedal hydraulic control. Extremely stable in operation due to its 4-wheel configuration.
Dead man's foot-pedal release mechanism ensures a controlled descent of the jack under load. Supplied with 4-arm transmission saddle. Will
accept adjustable gearbox support Model No: ADT5.
Rated capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1250kg
Ram extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Minimum saddle height . . . . . . . . . . . . . . . . . . . . . . . . .1120mm
Maximum saddle height . . . . . . . . . . . . . . . . . . . . . . . .1950mm
Base size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .680 x 700mm
Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51kg
This product has a fixed saddle.
Optional Adjustable Saddle Model No.. . . . . . . . . . . . . . . . ADT5
3. ASSEMBLY
Unpack the product and check contents. Should there be any
damaged or missing parts contact your supplier immediately.
3.1.
Assemble wheels as in figure 1. Refer to parts diagram for
guidance.
3.2.
Screw legs to the base of the stand and check that the stand is vertical before
tightening the leg screws.
3.3.
Place the saddle on the end of the central stand.
3.4.
Remove the transportation oil plug and replace with the operating plug
(identified by a hole in the plug head, fig 2).
INSTRUCTIONS fOR:
VERTICAL TRANSMISSION JACK
MODEL No:
fig 1
Original Language Version
1250TR.V2
fig 2
1250TR.V2
Issue: 2 - 13/10/09
Advertisement
Related Manuals for Sealey 1250TR.V2
Summary of Contents for Sealey 1250TR.V2
- Page 1 1250TR.V2 MODEL No: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMpORTANT: REAd ThESE INSTRUCTIONS CAREFULLY. NOTE ThE SAFE OPERATIONAL REQUIREMENTS, WARNINGS ANd CAUTIONS. USE ThIS JACK CORRECTLY ANd WITh CARE FOR ThE PURPOSE FOR WhICh IT IS INTENdEd.
- Page 2 5.4. RE-INSTALLING A GEARBOX. To transport, reposition beneath a vehicle, and raise a load, reverse the procedures outlined above. fig 4 Original Language Version 1250TR.V2 Issue: 2 - 13/10/09...
- Page 3 The oil level should be just below the oil plug hole. Oil capacity: 1ltr. WARNING! Only a good quality hydraulic Jack oil, such as SEALEY hYdRAULIC JACK OIL must be used, dO NOT use brake fluid. dO NOT overfill as this will render the jack inoperative.