Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ABB E-Hub 2.0
Summary of Contents for ABB E-Hub 2.0
- Page 1 DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A E-Hub 2.0 User manual...
-
Page 2: Intended Audience Of This Document
Revision History Revision Description Date Preliminary release September 2019 Market release January 2020 2 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A... -
Page 3: Table Of Contents
Which Screws are Used with the Mounting Bracket or 8 - REACH Compliance ............ 17 with the DIN Rail Mounting Clip ........39 9 - WEEE Compliance............17 3 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A... -
Page 4: Trademarks
1 - How to attach I/O module to E-Hub 2.0 ....55 2 - Basic configuration of I/O ........56 AI setting ................56 DI setting ................57 4 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A... -
Page 5: Introduction
ABB accepts no liability for damage to property or personal injury due to failure to comply with the instructions contained in this document. 3 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A... -
Page 6: Safety
All the information contained in this document is based on the latest information available at the moment of publication. We reserve the right to modify the document at any moment without prior notice. 4 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A Introduction | Safety... -
Page 7: Cyber Security
Install the unit in compliance with the environmental, electrical and mechanical limits described in the product documentation. • E-Hub 2.0 has been designed to operate with voltage and current values within the rated limits: do not install in systems that work at values exceeding these rated limits. •... -
Page 8: Warning Messages Used In This Document
NOTICE Sign (if necessary) Text that explains how to avoid damaging the supported product (or other property) 6 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A Introduction | Warning Messages Used in this Document... -
Page 9: Warning: Power Supply Safety
In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. 7 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A Introduction | Caution: Wireless Safety... -
Page 10: Conventions Used In This Document
Signal may be input or output Power and Ground Analog signal No Connection Reserved Use is reserved to ABB 8 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A CONVENTIONS USED IN THIS DOCUMENT | Conventions for Signal Types... -
Page 11: Product Overview
PRODUCT OVERVIEW 1 - Product Description The E-Hub 2.0 is a IoT Gateway designed to deliver LTE connectivity with 3G fallback to industrial and lightly rugged applications. Based on the TI AM335x Cortex-A8 (Sitara) processor family, with 1GB of RAM, 8GB of eMMC, and two MicroSIM card holders, these gateways are low-power and suitable for demanding use cases. -
Page 12: Intended Use And Not Allowed Uses Of The Product
3G Fallback Wireless Wi-Fi/Bluetooth 802.11a,b,g,n / BLE 4.2 Interfaces 2x SMA Cellular 2x RP-SMA Wi-Fi/ Antennas (external) Bluetooth 2x RP-SMA Wi-Fi/Bluetooth 10 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A PRODUCT OVERVIEW | Technical Specifications... - Page 13 Relative Humidity 5 to 95% (non-condensing) at +40°C (2) Software ensures that the system doesn’t exceed the maximum operating temperature (+70 °C) 11 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A PRODUCT OVERVIEW | Technical Specifications...
-
Page 14: Product Labels
ABB Serial Number Label ABB serial number On the left side of the product Activation code * the symbol stands for direct current 12 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A PRODUCT OVERVIEW | Product Labels... -
Page 15: Norms And Certifications
Some versions of the product described in this document are CE marked; for more information see “Technical Specifications” on page 10. ABB is not responsible for the use of this product together with equipment (for example: power supplies, personal computers, etc.) that are not CE marked and not compliant with the requirements specified in this document. -
Page 16: Fcc/Ised Regulatory Notices
ABB | E-Hub 2.0 4 - FCC/ISED Regulatory Notices Modification Statement ABB has not approved any changes or modifications to this product by the user. Any changes or modifications could void the user’s authority to operate the product. ISED Canada... -
Page 17: Rf Radiation Exposure Statement
• Contains FCC ID: UKMMRG1012 • Contains IC ID: 5131A-LE910NAV2 • Contains IC ID: 21442-MRG1012 • CAN ICES-3 (B)/NMB-3(B) 15 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A NORMS AND CERTIFICATIONS | FCC/ISED Regulatory Notices... -
Page 18: Restrictions On 5 Ghz Wi-Fi Usage
EU Restrictions on 5 GHz Wi-Fi Usage Due to EU restrictions on 5 GHz Wi-Fi bands the E-Hub 2.0 is limited to indoor operation and should only be operated in the frequency band 5150 MHz – 5250 MHz (U-NII-1) covering 20 MHz channels (36,40,44,48) and 40 MHz channels(38,46). -
Page 19: Antennas List
To avoid any possible legal implications, contact your local waste collection body for full collect and recycling information. 17 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A NORMS AND CERTIFICATIONS | WEEE Compliance... -
Page 20: Interfaces Overview
(only for E-Hub 2.0 with 3G) Antenna connector for 5 GHz Wi-Fi Not available COM 0/1 connector Digital I/Os connector 18 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES OVERVIEW | Front Side Interfaces Overview... -
Page 21: Rear Side Interfaces Overview
Ethernet ETH 1 connector Ethernet ETH 0 connector USB 0 connector USB 1 connector Service Panel Power IN connector 19 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES OVERVIEW | Rear Side Interfaces Overview... -
Page 22: Service Panel Interfaces
DIP-switch for serial ports configuration Programmable pushbutton Hardware reset pushbutton RTC backup supercap (not removable) MicroSIM card holder (push-pull) 20 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES OVERVIEW | Service Panel Interfaces... -
Page 23: Right Side Interface Overview
4 - Right Side Interface Overview The Right Side Interface is as follows: Fig. 5 Right Side Interfaces Layout Ref# Description Expansion connector 21 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES OVERVIEW | Right Side Interface Overview... -
Page 24: Left Side Interface Overview
The Left Side Interface is as follows: Fig. 6 Left Side Interface Layout Ref# Description 2.0 Host USB connector (ready to interface optional USB accessories) 22 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES OVERVIEW | Left Side Interface Overview... -
Page 25: Led Indicators Overview
LED Blinking: Internal Cellular Modem connected to cellular network POWER LED ON: Product powered by the external source Blue LED OFF: Product not powered by the external source 23 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES OVERVIEW | LED Indicators Overview... -
Page 26: Interfaces In Detail
Maximum RMS output power measured at 1dB from IEEE spectral mask or EVM. Parameter Value Operation frequency range 4910 to 5825MHz Output Power 16.8 dBm @ condition: 6 Mbps OFDM 24 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES IN DETAIL | Wi-Fi and Bluetooth... -
Page 27: Bluetooth Specifications
Supports up to 10 BLE connections • Independent buffering for LE allows having large number of multiple connections without affecting BR/EDR performance 25 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES IN DETAIL | Wi-Fi and Bluetooth... -
Page 28: Internal Cellular Modem (Only For E-Hub 2.0 With 3G Connectivity)
For optimum performance of the cellular interface, ABB recommends the use of both CELL MAIN and CELL DIV antenna connectors. 26 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES IN DETAIL | Internal Cellular Modem (only for E-Hub 2.0 with 3G connectivity) -
Page 29: Main Antenna Requirements
Depending by the frequency band(s) provided by the network Frequency range operator Impedance 50 Ohm ≤ 2:1 VSWR recommended 27 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES IN DETAIL | Internal Cellular Modem (only for E-Hub 2.0 with 3G connectivity) -
Page 30: The Microsim Card Holders
To remove the MicroSIM card, pull the eject lever: use a pen tip to simplify the operation: Fig. 9 28 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES IN DETAIL | Internal Cellular Modem (only for E-Hub 2.0 with 3G connectivity) -
Page 31: Com Ports
COM 1 has 2 pairs of pins (each signal is doubled): • If the E-Hub 2.0 is located at the beginning, or at the end, of a RS-485 chain, spare pair of pins can be used to connect permanently standard axial resistor 120 Ohm, if the application requires that •... -
Page 32: Com Connector Specifications
Type: 10-pin, 3.5 mm pitch • Example: Manufacturer: Shenzhen Connection Electronics Co., Ltd. Part Number: MC 1,5/10-STF-3,5 - 1847204 (or equivalent) 30 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES IN DETAIL | COM Ports... -
Page 33: Ethernet Ports
RJ-45 plug • Gender: Male Connector LEDs Layout: LEDs Meaning: Ref # LED Color LED Meaning Yellow Activity Green Link 31 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A INTERFACES IN DETAIL | Ethernet Ports... -
Page 34: Host Usb Ports
ABB | E-Hub 2.0 5 - Host USB Ports The E-Hub 2.0 provides 3x Host 2.0 USB ports (Noise and Surge Protected) for general purpose applications: • USB 0 on the rear side; max load: 500 mA • USB 1 on the rear side; max load: 500 mA •... -
Page 35: Expansion Connector
ABB | E-Hub 2.0 6 - Expansion Connector The E-Hub 2.0 provides, on the right side, an expansion connector with the following interfaces: • I/O additional Module • LoRa additional module 7 - The Programmable Pushbutton The E-Hub 2.0 provides a pushbutton in the Service Panel. -
Page 36: Mechanical Specifications
139 (L) x 115 (W) x 46 (H); mm - Antennas Connectors and Mounting Bracket included. All dimensions are in millimeters. Fig. 12 34 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A MECHANICAL SPECIFICATIONS | Product Mechanical Dimensions... -
Page 37: Mounting Bracket Mechanical Dimensions
ABB | E-Hub 2.0 2 - Mounting Bracket Mechanical Dimensions The Mounting Bracket fastened on the bottom side of the E-Hub 2.0 has the following dimensions. All dimensions are in millimeters. Fig. 13 35 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A... -
Page 38: How To Install The Product
The product must be installed in a secured location, accessible to authorized personnel only (for example in a cabinet / technical compartment). By default, the E-Hub 2.0 comes with a DIN rail mounting clip fastened on the bottom side. You can use this to install the E-Hub 2.0. -
Page 39: How To Replace The Mounting Bracket With The Din Rail Mounting Clip Or Vice Versa
4. Tighten the 3 screws removed at step 1 by applying a torque of 0.7 Nm Fig. 15 37 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO INSTALL THE PRODUCT | How to Replace the Mounting Bracket with the DIN Rail Mounting Clip or Vice Versa... -
Page 40: How To Replace The Din Rail Mounting Clip With The Mounting Bracket
4. Tighten the 3 screws removed at step 1 by applying a torque of 0.7 Nm Fig. 16 38 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO INSTALL THE PRODUCT | How to Replace the Mounting Bracket with the DIN Rail Mounting Clip or Vice Versa... -
Page 41: Which Screws Are Used With The Mounting Bracket Or With The Din Rail Mounting Clip
Reference Value (mm) Φ Φ 39 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO INSTALL THE PRODUCT | How to Replace the Mounting Bracket with the DIN Rail Mounting Clip or Vice Versa... -
Page 42: How To Install/Remove The Product On/From A Din Rail
DIN rail 2. Pull the product out Fig. 19 40 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO INSTALL THE PRODUCT | How to Install/Remove the Product on/from a DIN Rail... -
Page 43: How To Supply Power To The Product
• Manufacturer: Phoenix Contact • Part Number: MC 1,5/ 3-STF-3,5 - 1847068 • (or equivalent) 41 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO SUPPLY POWER TO THE PRODUCT | Power Supply Specifications... -
Page 44: How To Supply Power And Turn On The Product
9. Connect power after the installation of the system has been completed 10. Never connect or disconnect the cables with the system or the external apparatus switched ON. To supply power and turn ON the E-Hub 2.0, complete the following steps: 1. Setup a DC power source that: •... -
Page 45: How To Trigger A Hardware Reset Of The Product
ABB | E-Hub 2.0 3 - How to Trigger a Hardware Reset of the Product To trigger a hardware reset of the E-Hub 2.0, push the reset pushbutton available in the Service Panel. Fig. 21 43 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A... -
Page 46: How To Maintain The Product
2. To remove dust from the case of the product, use a dry, lint-free, cloth 3. To remove the dirt, use water-based, non-flammable, cleaner products. 44 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO MAINTAIN THE PRODUCT | How to Clean the Product... -
Page 47: Basic Configuration Via Ekip Connect 3
Warnings Do not incorrectly configure the software, as this can lead to inaccurate data results. Be sure that you laptop is connected directly to ETH1 of the E-Hub 2.0. Connect E-Hub 2.0 Please use Ekip Connect 3 to connect E-Hub 2.0 •... -
Page 48: General Settings
Click Information to enter the page of configure. Configure device’s name, time and date of installation according to the actual situation. Fig. 25 46 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A Basic configuration via Ekip Connect 3 | General Settings... -
Page 49: Time Zone Settings
Click Configuration to enter the page of configure. Click SNTP box and select the appropriate Time zone in the drop-down list. Input a valid • SNTP server address, then switch on SNTP client enable, E-Hub 2.0 will sync time with SNTP server. Fig. 26 Gateway enable The Gateway enable setting allows user to access E-Hub 2.0’s RTU devices. -
Page 50: Language
N81: None parity, 8 data bits, 1 stop bit • Click Save the configuration. • Reboot the E-Hub 2.0 will make the configuration valid. 48 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A Basic configuration via Ekip Connect 3 | Communication Settings... - Page 51 NOTE: Please always remember the input ETH1 static IP address before save the changes. For the provisioning part please refer to the Getting started of the E-Hub 2.0. 49 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A...
-
Page 52: Annex 1: Additional I/O Module
I/O module is a fast and simple way to expand the capabilities of E-Hub 2.0 Gateway with extra digital and analog ports. Designed to be fitted to the side of the E-Hub 2.0, it is rated for the same level of reliability and operating temperature range. The digital section... -
Page 53: Product Labels
• product name • product model • I/O module serial number • FCC logo • CE mark • WEEE symbol 51 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A Annex 1: Additional I/O module | Product labels... -
Page 54: Declaration Of Conformity
This product is CE marked. The product meets the guidelines listed in the following sections. ABB is not responsible for the use of this product together with equipment (eg power supplies, personal computers, etc) that are not CE marked and compliant with the requirements specified in this document. -
Page 55: Electromagnetic Compatibility
IP40 (enclosure only, excluding connectors) Enclosure Material: ABS - Colour: aluminium Mechanical Dimensions 90.3 x 59 x 43.7 mm (WxLxH) 53 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A DECLARATION OF CONFORMITY | Electromagnetic Compatibility... -
Page 56: Mechanical Specifications
The I/O module enclosure is supplied on a mounting plate having the dimensions shown in the drawing (Figure 12.1) below: All dimensions are in millimetres. Fig. 32 54 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A MECHANICAL SPECIFICATIONS | I/O module mechanical dimensions... -
Page 57: How To Install The Product
HOW TO INSTALL THE PRODUCT 1 - How to attach I/O module to E-Hub 2.0 • Attach the I/O additional module 10-12-xx unit to the E-Hub 2.0 as shown below using M2.5 x 5 CAP Head screw. • Screw the I/O additional module module mounting plate to the same flat surface as the E-Hub 2.0... -
Page 58: Basic Configuration Of I/O
Voltage AI: 0 V to +36 V Voltage AI: 0 V to +36 V Unit Unit for the measurement 56 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO INSTALL THE PRODUCT | Basic configuration of I/O... -
Page 59: Di Setting
DI channel, please do a re-provisioning process to make the changes valid. 57 | © 2019 ABB | DOC. N° 1SDH002109A1001 - ECN000125349 - Rev. A HOW TO INSTALL THE PRODUCT | Basic configuration of I/O...