Advertisement
Quick Links
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are
p
adhered to when using this equipment.
WARNING! Disconnect from air supply before changing accessories or servicing.
p
Maintain the sander in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and
3
will invalidate the warranty.
Use in a suitable clean and tidy working area, free from unrelated materials and ensure there is adequate
3
lighting.
Before each use check abrasive pads for condition. If worn or damaged replace immediately.
3
Ensure the abrasive pad rating is equal to, or greater than the RPM rating of the sander.
3
Ensure there are no flammable or combustible materials near the work area.
3
WARNING! Always wear approved eye or face and hand protection when operating the sander.
p
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery, and contain and/or tie back
3
long hair.
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the working area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
3
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure
p
70-90psi
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and
3
ensure that all connections are secure.
Prolonged exposure to vibration from this sander poses a health risk. It is the operator's responsibility to
3
correctly assess the potential hazard and issue guidelines for safe periods of use and offer suitable
protective equipment.
DO NOT use the sander for a task it is not designed to perform.
7
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal
7
injury.
DO NOT use cloth backed sanding pads. Use only appropriate paper adhesive pads, following pad
7
instructions.
WARNING! DO NOT sand any materials containing asbestos.
p
DO NOT carry the sander by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to the sander, let the sander do the work.
7
DO NOT place attachments close to your face and do not point at other persons or animals.
7
DO NOT operate sander when you are tired, under the influence of alcohol, drugs or intoxicating
7
medication.
DO NOT use sander where there is flammable liquids, solids or gases such as paint solvents and
7
including waste wiping or cleaning rags etc.
DO NOT carry the sander with your finger on the power lever.
7
DO NOT direct air from the air hose at yourself or others.
7
When not in use disconnect from air supply and store in a safe, dry, childproof location.
3
© Jack Sealey Limited 2013
INSTRUCTIONS FOR:
AIR PALM ORBITAL SANDER150mm
SA08 & SA09
MODEL Nos:
Original Language Version
(DUST FREE:SA09)
SA08,SA09
Issue: 3(SP) - 07/02/14
Advertisement
Related Manuals for Sealey SA09
Summary of Contents for Sealey SA09
- Page 1 (DUST FREE:SA09) MODEL Nos: Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
- Page 2 Air Inlet: ..... 1/4”BSP Vacuum outlet (SA09 only)..Ø28mm Thread size: ....5/16” UNF Noise Power: .
-
Page 3: Environmental Protection
Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty. 5.1. Lubricate the air sander daily with a few drops of good grade air tool oil such as Sealey ATO500S or ATO1000S, dripped into the air inlet before use. 5.2. - Page 4 Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work. Original Language Version © Jack Sealey Limited 2013 SA08,SA09 Issue: 3(SP) - 07/02/14...