Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear eye
instructions
protection
1. safety
1.1.
eleCtriCal safety
warninG! it is the responsibility of the owner and the operator to read, understand and comply with the following: You must
‰
check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety
devices. A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend
that a residual current device (rcd) is used. it is particularly important to use an rcd with portable products that are plugged
into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current
device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
the electricity at Work Act 1989 requires that all portable electrical appliances, if used on business
9
premises, are tested by a qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe
9
condition of those appliances and the safety of the appliance operators. if in any doubt about electrical safety,
contact a qualified electrician.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power
9
supply.
insure that cables are always protected against short circuit and overload.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure
9
that none are loose.
Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the
9
correct fuse - see fuse rating at right.
dO nOt pull or carry the appliance by the power cable.
8
dO nOt pull the plug from the socket by the cable.
8
dO nOt use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified
8
electrician. When a Bs 1363/A uK 3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) connect the Green/YelloW earth wire to the earth terminal 'e'.
b) connect the BroWn live wire to the live terminal 'l'.
c) connect the Blue neutral wire to the neutral terminal 'n'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends
beyond the cable restraint and that the restraint is tight. double insulated products, which are always marked with this symbol, are
fitted with live (brown) and neutral (blue) wires only. to rewire, connect the wires as indicated above - dO nOt connect either wire to
the earth terminal.
Products which require more than 5 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
9
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
General safety
1.2.
warninG! ensure Health & safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
warninG! disconnect from mains power before changing accessories, servicing or maintenance.
‰
maintain the sander in good condition (use an authorised service agent).
9
replace or repair damaged parts. use recommended parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
use sander in a suitable working area. Keep area clean, tidy and free from unrelated materials. ensure there is adequate lighting.
9
Before use check sanding belt. if worn or damaged replace immediately.
9
warninG! Always wear approved eye or face protection when operating the sander.
‰
if dust is generated, use face, dust, or respiratory protection in accordance with cosHH regulations.
9
depending on task, sander noise level may exceed 85dB in which case wear safety ear defenders.
9
remove ill fitting clothing, ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of the sanders working parts.
9
© Jack sealey limited
instructions for
Variable speed belt sander 400w/230V
model no:
Wear protective
Wear safety
gloves
footwear
Original Language Version
sbs35
Wear protective
Wear ear
clothing
protection
Wear a mask
reCOMMended fUse
ratinG: 5a
sBs35 | issue 4 08/12/16
Advertisement
Related Manuals for Sealey SBS35
Summary of Contents for Sealey SBS35
- Page 1 Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 3. We recommend personal protection by using the following safety items: a) Paint spray respirator (sealey ref. ssP16en) b) Pe coated Hooded coverall (sealey ref. ssP266). c) latex Gloves (sealey ref. ssP24). 4. take adequate measures to contain the paint dust, flakes and scrapings.
- Page 3 (fig.2B, fig.3d) forward, this will shorten the length of the arm and loosen the sanding belt. slide the old belt off and replace with the same size belt. Pull the lever (fig.2B, fig.3D) back to tighten the belt. To change the arm and belt repeat from 4.1 ”PREPARING FOR USE” Original Language Version sBs35 | issue 4 08/12/16 © Jack sealey limited...
- Page 4 When not in use store in a safe, dry, childproof location. parts support is available for this product. to obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. environmental protection recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.