hit counter script
Baroness GM2810A Owner's Operating Manual
  1. Manuals
  2. Brands
  3. Baroness Manuals
  4. Lawn Mower
  5. GM2810A
  6. Owner's operating manual

Baroness GM2810A Owner's Operating Manual

5-unit rotary mower
Hide thumbs Also See for GM2810A:
Table of Contents

Advertisement

Quick Links

Download this manual
5-Unit Rotary Mower
Owner's Operating Manual
Serial No.
GM2810A：11001-
"Required reading"
Read this manual and the Owner's Manual for the engine before using the machine.
Original Instructions Ver.1.0

Advertisement

Table of Contents
loading

Related Manuals for Baroness GM2810A

Summary of Contents for Baroness GM2810A

  • Page 1 5-Unit Rotary Mower Owner's Operating Manual Serial No. GM2810A：11001- "Required reading" Read this manual and the Owner's Manual for the engine before using the machine. Original Instructions Ver.1.0...
  • Page 2 GM2810A Regulations California Proposition 65 EU Emission Control (StageⅤ) (For California, USA) (For Europe) Important WARNING: No deliberate tampering with or misuse of the Operating, servicing and maintaining engine emissions control system should take a passenger vehicle or off-road place.
  • Page 3 GM2810A Greeting Thank you for purchasing the Baroness product. This manual describes the proper handling, adjustment, and inspection of your product. We hope you will use the product safely, and take advantage of its best performance. Keeping The Owner's Operating...
  • Page 4 The operator is responsible for operating the product properly and safely. Maintenance should only be performed by a certified specialist. If you have any questions concerning maintenance or genuine parts, please contact a Baroness dealer or Kyoeisha. When making inquiries about the product, please specify the product's model designation and serial number.
  • Page 5 GM2810A Introduction Purpose This product is intended for cutting turf grass at golf courses. Do not use this product in any way other than its intended purpose, and do not modify this product. Operating this product for other purposes and modifying it may be very dangerous and may cause damage to the product.
  • Page 6 GM2810A Introduction...

  • Page 7: Table Of Contents

    GM2810A Contents Safety .............. Page 1-1 Safe Operating Practices .......Page 1-2 Disposal ............Page 2-1 Recycle and Waste Disposal ......Page 2-2 Product Overview .......... Page 3-1 Specifications ..........Page 3-2 Names of Each Section ......... Page 3-4 Regulation Decals ..........Page 3-5 Safety Signs and Instruction Signs ....
  • Page 8 GM2810A Contents...

  • Page 9: Safety

    GM2810A Safety Safe Operating Practices ...... Page 1-2 Training ..........Page 1-2 Preparation ..........Page 1-2 Operation ..........Page 1-3 Maintenance and Storage ..... Page 1-4 Page 1-1...

  • Page 10: Safe Operating Practices

    GM2810A Safety Failure to adequately follow these safety Never allow children or people unfamiliar precautions may cause an accident resulting in with these instructions to use or service the injury or death. machine. Local regulations may restrict the age of the...
  • Page 11 GM2810A Safety Add fuel before starting the engine. Engage clutch slowly, always keep Never remove the cap of the fuel tank or machine in gear, especially when traveling add fuel while the engine is running or downhill. when the engine is hot.
  • Page 12 GM2810A Safety After striking a foreign object or if an Reduce the throttle setting during engine abnormal vibration occurs. run-out and, if the engine is provided with a Inspect the machine for damage and shut-off valve, turn the fuel off at the make repairs before restarting and conclusion of operation.
  • Page 13 GM2810A Safety When checking the hydraulic circuit for pinhole leaks or oil leakage from nozzles, do not use your hands. Use items such as paper or corrugated cardboard to find leakage points. Be extremely careful with high-pressure oil as it may pierce your skin, result.
  • Page 14 GM2810A Safety Page 1-6 Safe Operating Practices...

  • Page 15: Disposal

    GM2810A Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1...

  • Page 16: Recycle And Waste Disposal

    GM2810A Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations.

  • Page 17: Product Overview

    GM2810A Product Overview Specifications ........Page 3-2 Specifications .........Page 3-2 Sound Pressure Level ......Page 3-3 Sound Power Level ....... Page 3-3 Vibration Level ........Page 3-3 Carbon Dioxide (CO2) Emissions Measurement .........Page 3-4 Names of Each Section ......Page 3-4 Regulation Decals ........Page 3-5...

  • Page 18: Specifications

    GM2810A Product Overview Specifications Specifications Model GM2810A Total length 145.67 in 370 cm During 118.11 in 300 cm operation Total width During Dimensions 90.55 in 230 cm transport Roof 90.55 in 230 cm Total height Steering 64.96 in 165 cm...

  • Page 19: Sound Pressure Level

    GM2810A Product Overview Sound Pressure Level Sound Pressure Level This machine was confirmed to have a continuous A-weighted sound pressure level of 90dB by measuring identical machines in accordance with the procedure specified in ISO 5395-1:2013. Sound Power Level Sound Power Level...

  • Page 20: Names Of Each Section

    GM2810A Product Overview Carbon Dioxide (CO ) Emissions Seat Measurement Steering handle Tilt lever For CO emissions measurement on the Diff-lock switch engine of this machine, refer to the engine's Parking brake lever owner's manual. Brake pedal Names of Each Section...

  • Page 21: Regulation Decals

    GM2810A Product Overview Regulation Decals Specification Decal (For Europe) Positions of Regulation Decals The Specification decal indicates the CE marking, model , and weight, etc. G,H,I quwxcl-193 Positions of Regulation Decals_001 kj8jic-001 Specification Decal_001 Serial number plate Specification decal Noise Emission Decal...
  • Page 22 GM2810A Product Overview ROPS Compliance Decal Recycle Decal The ROPS compliance decal indicates the Recycle Decal illustrates Recycle Mark in manufacturer, model, etc., in accordance with accordance with local regulation. International Standard ISO 21299:2009. (For Europe) y7wov5-001 c3td3e-003 ROPS Compliance Decal_001...
  • Page 23 GM2810A Product Overview Indicating Diesel Fuel Decal Spark Arrester Warning Decal (For USA) (For the State of California, USA) Indicating diesel fuel decal describes the type Spark arrester warning decal describes the of fuel to be used. warning messages as required by California Use Ultra Low Sulfur Diesel Fuel (sulfur-free Public Resources Code.

  • Page 24: Safety Signs And Instruction Signs

    6iul4h-183 Positions of Safety Signs and Instruction Signs_002 Part numbers for decals that need to be replaced are listed in the parts catalog. Order them from a Baroness dealer or Kyoeisha. Positions of Safety Signs and Instruction Signs 6iul4h-040...
  • Page 25 GM2810A Product Overview Operation decal Engine start/stop decal Caution to mutilation decal Caution for high temperatures decal Caution to injury decal Caution to rotating object decal Hydraulic oil icon Diesel fuel icon Fire prohibited decal 6iul4h-056 Caution for mower lock decal...

  • Page 26: Description Of Safety Decals And Instruction Decals

    Turn the key to the "ON (GLOW)" Warning position, and then wait for the logo "BARONESS" to be turned off. Apply the parking brake, stop the engine, Turn the key to the "START" position. remove the ignition key, and then leave the machine.
  • Page 27 GM2810A Product Overview Caution to Mutilation Decal Caution to Injury Decal K4205001600 K4205001580 DECAL, CAUTION TO MUTILATION Decal, caution to injure Warning Caution May cut your hand or leg - Stop the cutter May pinch - There is a risk of being pinched.
  • Page 28 GM2810A Product Overview Hydraulic Oil Icon Fire Prohibited Decal K4209000980 K4205001940 Hydraulic oil icon Decal, fire prohibited Read the Owner's Operating Manual. Warning Keep away from fire. i77xz6-001 Hydraulic Oil Icon_001 Diesel Fuel Icon r653fo-001 K4209001000 Fire Prohibited Decal_001 Diesel fuel icon Caution for Mower Lock Decal Use diesel fuel.
  • Page 29 GM2810A Product Overview Caution for Spouting Coolant Decal Caution to Flying Object Decal K4205001970 K4205001650 Decal, caution for spouting coolant Decal, caution to flying object Caution Caution Caution for spouting coolant - Do not open Caution to flying object - Be sure that people while hot.
  • Page 30 GM2810A Product Overview Caution Exhaust Gas Decal Maintenance Decal K4205001950 K4209001540 Decal, caution exhaust gas Maintenance decal The maintenance decal indicates the Warning necessary inspection and maintenance items for this machine. Caution for exhaust gas Q U I C K R E F E R E N C E A I D 8･9...

  • Page 31: Handling Instructions

    GM2810A Handling Instructions Inspections ..........Page 4-2 2WD/4WD Selector Switch ....Page 4-28 DPF Auto Regeneration Inhibit Rotary Knife ........... Page 4-2 Switch ..........Page 4-29 Radiator Cover ........Page 4-2 DPF Parked Regeneration Switch ..Page 4-30 Radiator ..........Page 4-3 Light Switch .........

  • Page 32: Inspections

    GM2810A Handling Instructions Make sure that there are no cracks or tears Inspections between the sail and flat part of the rotary knife. Inspect the machine according to the maintenance schedule so that you will be able to take advantage of its optimum performance for a long period of time.

  • Page 33: Radiator

    GM2810A Handling Instructions Radiator cover Oil cooler Rubber catch Carefully clean the front and back of the Radiator radiator cover with water or compressed air. Carefully clean the front and back of the Radiator radiator with water or compressed air.

  • Page 34: Oil Cooler

    GM2810A Handling Instructions If no coolant is in the reserve tank, follow Coolant Supply the steps below to fill the tank with clean water. Caution Open the radiator cap, and then supply Do not touch the radiator or coolant during clean water up to the opening.

  • Page 35: Hydraulic Oil

    GM2810A Handling Instructions Unlock the rubber catches on the left and Important right of the oil cooler, and then tilt the oil cooler. Use Shell Tellus S2M46 (or equivalent) as hydraulic oil. If the oil level is low, remove the left tank cover, and then open the tank cap and supply oil.

  • Page 36: Air Cleaner

    GM2810A Handling Instructions Attach the outer element to the air Air Cleaner cleaner body. Inspection of Air Cleaner Replace the air cleaner cap, and then fix it securely using the clips. Liners and piston rings so that the engine will always operate smoothly.

  • Page 37: Battery

    GM2810A Handling Instructions Battery Supply of Battery Fluid Inspection of Battery Danger Danger Be careful not to let your skin, eyes or clothes, Danger Danger etc., come into contact with the battery fluid or Keep away from fire while inspecting or accidentally swallow the fluid.

  • Page 38: Tire

    GM2810A Handling Instructions If the wire is cracked or damaged, replace it Tire with a new one immediately. Inspection of Tires Around The Engine Check the pneumatic pressure of the tires. Inspection of Engine-Associated Parts Make sure that there are no cracks, damage or abnormal wear.

  • Page 39: Fuel

    GM2810A Handling Instructions The appropriate oil level should be between Replace the oil filler cap. the upper and lower limit lines on the gauge. kx9tif-006 Supply of Engine Oil_001 rnr453-002 Oil filler cap Inspection of Engine Oil_002 It will take a while for the supplied engine oil Oil level gauge to descend into the oil pan.

  • Page 40: Water Separator

    GM2810A Handling Instructions A priming pump is installed on the feed Fuel Supply pump. Repeatedly press the top of the priming Warning pump with your finger until resistance is felt, to bleed air. Do not supply additional fuel after the fuel level indicates 100%.
  • Page 41 GM2810A Handling Instructions Cleaning of Water Separator Float For details on handling the engine, please Water drain plug refer to the Engine's Owner's Manual. Element Important Air-bleeding bolt If water contaminates the fuel, the supply Draining of Water Separator pump and injector may be burnt out.

  • Page 42: Fuel Filter

    GM2810A Handling Instructions Fuel Filter Inspection of Fuel Filter The fuel filter is positioned between the fuel strainer and the engine, and cleans the fuel flowing into the carburetor. When the fuel flow becomes insufficient, replace the fuel filter if necessary.

  • Page 43: Tightening Torques

    GM2810A Handling Instructions Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine.
  • Page 44 GM2810A Handling Instructions General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49...

  • Page 45: Principal Tightening Torques

    GM2810A Handling Instructions Principal Tightening Torques Tightening Torque by Model GM2810A Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant).
  • Page 46 GM2810A Handling Instructions Tightening torque Thread locking Location Code Part name adhesive kgf-cm lb-in Slotted nut of tie rod end K1610000020 458.87 398.30 － Tie rod Slotted nut of tie rod end K1611000020 458.87 398.30 － 67 - 683.20 - 593.02 -...

  • Page 47: Adjustment Before Work

    GM2810A Handling Instructions Use the backrest tilt adjustment lever to Adjustment before Work adjust the angle of the backrest. Adjustment of Steering Wheel Turn the suspension adjustment handle to adjust the firmness of the seat suspension. Observe the suspension adjustment scale Warning while making adjustments.

  • Page 48: Adjustment Of Cutting Height

    GM2810A Handling Instructions (#11042 -) Adjusting plate position 1 Use the forward/backward adjustment lever Adjusting plate position 2 to adjust the seat back and forth. Adjusting plate position 3 Use the tilt adjustment lever to adjust the Adjusting plate position 4 angle of the backrest.
  • Page 49 GM2810A Handling Instructions Adjustment With Adjusting Collars Adjusting collars are installed at three locations on each mower deck. Important The length of grass cut off at any one time must be no more than 30.0 mm (1.18 in). Important s8skgg-002...
  • Page 50 GM2810A Handling Instructions Lower the mower deck to change the Adjustment With Cutting Height Adjusting Plates hole positions, and then temporarily secure it with the two bolts. Cutting height adjusting plates are installed at three locations on each mower deck.

  • Page 51: Procedure To Start/Stop Engine

    "Low speed" position toward the "High result in damage to the machine. speed" position. Switch the ignition key to the "ON (GLOW)" After the "BARONESS" logo and the yellow position. and red LEDs go off and the parameters (items and values such as the rotation speed) appear, immediately set the ignition key to the "START"...

  • Page 52: Safety Mechanisms

    GM2810A Handling Instructions Warning Mechanisms Procedure to Stop Engine Set the traveling pedal to the neutral Important position. When the buzzer (intermittent tone) sounds, Apply the parking brake. be sure to stop operation since the engine is Set the knife rotation switch to the "Stop"...

  • Page 53: Operation Method

    GM2810A Handling Instructions Operation Method Key switch decal Knife rotation mark Cautions for when You Leave The Traction assist mark Machine 2WD/4WD selector mark DPF regeneration mark (EN) Caution Mower deck up/down mark If the brakes are not sufficiently effective, use Light switch mark the wheel stoppers to secure the machine.
  • Page 54 GM2810A Handling Instructions Knife Rotation Mark 2WD/4WD Selector Mark Knife rotation mark 2WD/4WD selector mark It illustrates Rotation/Stop of the rotary knife. This indicates the 2WD/4WD positions. O F F 6ntnq3-002 sdts98-002 Knife Rotation Mark_001 2WD/4WD Selector Mark_001 Rotation Stop...
  • Page 55 GM2810A Handling Instructions Mower Deck Up/Down Mark Engine Rotation Mark Mower deck up/down mark Engine rotation mark This indicates the Up/Down positions of the This indicates low/high speed of engine mower deck. rotation. D O W N 8kzlbt-002 kp2t9l-001 Mower Deck Up/Down Mark_001...
  • Page 56 GM2810A Handling Instructions Tilt Steering Decal FORWARD Decal K4203001350 K4203001430 Decal, tilt steering Decal, FORWARD This illustrates the tilt directions of the This indicates forward travel. steering wheel and the locked/free positions. FORWARD FREE LOCK kqca3e-001 hj3943-003 FORWARD Decal_001 Tilt Steering Decal_001...

  • Page 57: Proximity Sensors

    GM2810A Handling Instructions Proximity Sensors There are two proximity sensors on mower arm fulcrums #4 and #5. These sensors detect the raised or lowered positions of mower decks #4 and #5. The information is related to controlling rotation and stop of the rotary knives.

  • Page 58: Knife Rotation Switch

    GM2810A Handling Instructions Knife Rotation Switch 2WD/4WD Selector Switch Caution Caution Set the knife rotation switch to the "Rotation" When working on a slope, be sure to use the position immediately before starting cutting machine in 4WD. work. At all other times, be sure to leave the knife rotation switch set to the "Stop"...

  • Page 59: Dpf Auto Regeneration Inhibit Switch

    GM2810A Handling Instructions DPF Auto Regeneration Inhibit Switch Caution Normally, set the DPF auto regeneration inhibit switch to "Auto regeneration mode". However, when operating in a location where fires may occur, set the DPF auto regeneration inhibit switch to "Auto regeneration inhibit mode".

  • Page 60: Dpf Parked Regeneration Switch

    GM2810A Handling Instructions DPF Parked Regeneration Switch Light Switch Note: Danger Danger Depending on the specifications, this function may not be available. Do not perform DPF regeneration in a location where fires may occur since it will become Caution extremely hot around the exhaust outlet during DPF regeneration.

  • Page 61: Traction Assist Switch

    GM2810A Handling Instructions Traction Assist Switch The traction assist switch is located in the operation panel. This switch is effective to increase climbing ability when this machine is in cutting operation (4WD). The cylinders are pressurized even with the ･...

  • Page 62: Throttle Knob

    GM2810A Handling Instructions Mower deck up/down lever Raise Neutral Lower Throttle Knob The throttle knob is located to the right of the driver's seat and enables you to adjust the engine rpm. Move the throttle knob toward the "High speed"...

  • Page 63: Brake Pedal

    GM2810A Handling Instructions Brake Pedal Change of Braking Method Follow the procedure below to change the Warning braking method from linked to independent. Link the brake pedals, except when operating Swing up the pedal link bar, and then pull it the machine.

  • Page 64: Parking Brake Lever

    GM2810A Handling Instructions Parking Brake Lever Caution Never park the machine on a slope. Important Be sure to release the parking brake before driving. It may result in the brakes or hydraulic system i5jb7e-017 malfunction. Hood_001 Rubber catch The parking brake lever is located to the left of Left hood the front cover.

  • Page 65: Instruments

    GM2810A Handling Instructions Underseat Cover Monitor display LED (yellow) Caution LED (red) Enter key Be careful not to pinch your fingers when you Right arrow key open or close the underseat cover. Left arrow key Make sure that the steering wheel is raised Menu key completely.

  • Page 66: Displayed Icon

    GM2810A Handling Instructions Displayed Icon Main Menu Items The icon appears at the top of the monitor While any parameter is displayed, press the display. menu key to display the main menu with the following 11 items. ･ GO TO 1-UP DISPLAY / GO TO 4-UP DISPLAY ･...
  • Page 67 GM2810A Handling Instructions 4-up display Four parameters are displayed in the monitor display. With the 4-up display, a total of 8 parameters are displayed over 2 pages. 0 RPM 83 % ENG RPM % SOOT 19 C 53 % COOL TEMP...
  • Page 68 GM2810A Handling Instructions Parameter Items ￭ The parameters and corresponding information that appear in the monitor display are listed below. Monitor display L Monitor display S Description ENGINE SPEED ENG RPM Displays the engine rpm. DRIVERS DEMAND DEMAND TQ Displays the torque required by the ECU.
  • Page 69 GM2810A Handling Instructions Monitor display L Monitor display S Description EXHAUST FILTER Displays the DPF outlet gas temperature measured by the EF OUT T OUTLET TEMP exhaust temperature sensor. Shows the status of the regeneration icon. PARTICUATE TRAP PT LAMP Icon not displayed="OFF", Icon blinking="ON BLINK", Icon...
  • Page 70 GM2810A Handling Instructions Text 2 ･ Language With "LANGUAGES", the language used in the monitor display can be set to either of the following two. 1 of 4 C : 3 SPN 172 FMI 3 ･ ENGLISH CORRECTIVE ACTION: S e e S e r v i c e M a n u a l JAPANESE ･...
  • Page 71 GM2810A Handling Instructions List of Fault Codes ￭ Important When the fault code appears in the monitor display, refer to "Kubota DIAGNOSIS MANUAL COMMON RAIL SYSTEM" or contact your dealer. The fault codes (DTC) and corresponding information that appear in the monitor display are listed below.
  • Page 72 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output Stop ENG Fuel leak (in - Worsening consumption is To minimize PM Key switch turn...
  • Page 73 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output - Worsening exhaust gas Open circuit or +B Stop ENG emissions short circuit of...
  • Page 74 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Engine speed See Service Diagnostic Engine overrun P0219 exceeds - Overrun 　 Manual counter = zero...
  • Page 75 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 (At low temperature) Ground short of Ground short of See Service Key switch turn glow relay...
  • Page 76 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output Injector charge Stop ENG voltage: Low Injector charge - Worsening Key switch turn...
  • Page 77 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Faulty starting - Insufficient output Sensor supply Sensor supply See Service Key switch turn - Worsening...
  • Page 78 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Accelerator position sensor Diagnostic Accelerator signal error counter = zero See Service - Insufficient Position Sensor...
  • Page 79 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output CAN2 +B or GND See Service Key switch turn CAN2 Bus off U0075...
  • Page 80 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Exhaust gas Open circuit or +B See Service Key switch turn temperature P0544 3242 short circuit of None 　...
  • Page 81 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Differential Ground short See Service Key switch turn pressure P2454 3251 circuit of sensor None 　...
  • Page 82 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Stop engine!! PM accumulation To minimize PM - Insufficient Diagnostic Excessive PM4 Contact dealer P3007 3701...
  • Page 83 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Worsening exhaust gas Over heat pre- See Service Diagnostic P3025 523603 15 Coolant temp. 　...
  • Page 84 GM2810A Handling Instructions Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Loss of DPF See Service Loss of functon of P3015 3936 Function Manual Open Circuit of...
  • Page 85 GM2810A Handling Instructions "RESTORED TO DEFAULTS" appears in Engine Configuration the monitor display, and the parameters are reset to the factory defaults of the This function is not supported. following 8 items. 1-Up Display Setup ENGINE SPEED With "SETUP 1-UP DISPLAY", the displayed...
  • Page 86 GM2810A Handling Instructions Highlight "CUSTOM SETUP", and then To deselect a parameter and remove it press the Enter key. from the list of displayed parameters The list of parameters appears. Highlight the parameter, and then press the Enter key. USE DEFAULTS...
  • Page 87 GM2810A Handling Instructions After the settings have been applied, Automatic Scan ￭ pressing the menu key once returns to the main menu, and pressing the key again With "AUTOMATIC SCAN", the 1-up display returns to the 1-up/4-up display screen. can be set to automatically scroll through the Note: selected parameters one by one.
  • Page 88 GM2810A Handling Instructions Highlight "USE DEFAULTS", and then Custom Setup ￭ press the Enter key. With "CUSTOM SETUP", the type and number of parameters as well as their display order can be specified. Press the menu key. After the main menu...
  • Page 89 GM2810A Handling Instructions Select the page. The parameters appear. The number at the right of the Check that the values for the four parameter indicates the location in the parameters are highlighted. 4-up display. 1=Upper left 2=Lower left 3=Upper right...
  • Page 90 GM2810A Handling Instructions Check that a number appeared to the Check that the number at the right of right of the selected parameter. the parameter disappeared. ENGINE SPEED ENGINE SPEED DRIVERS DEMAND ENGINE TORQUE 4 DRIVERS DEMAND ENGINE TORQUE 4...
  • Page 91 GM2810A Handling Instructions Use the arrow keys to highlight the item to Reset Reminders ￭ be changed, and then press the Enter key. A plus appears at the right of the currently With "RESET REMINDER", displayed selected items. remaining time can be reset to the time specified with "MODIFY REMINDERS".
  • Page 92 GM2810A Handling Instructions Highlight "MODIFY REMINDERS", and Modify Reminders ￭ then press the Enter key. With "MODIFY REMINDERS", the replacement time period for consumables can be specified. The factory default replacement time periods RESET REMINDERS are the initial time periods.
  • Page 93 GM2810A Handling Instructions Highlight the digit to be changed. Reminder Display ￭ Press the right arrow key to increase the number. Press the left arrow key to Important change the digit. If a warning message appears, immediately stop operation, and then perform the replacement procedure.
  • Page 94 GM2810A Handling Instructions Select Units Units Monitor display S ENGLIS METRI METRI With "SELECT UNITS", the units of parameter C KPA C BAR values can be set to any of the following three ENG RPM formats. DEMAND TQ ％ ％...
  • Page 95 GM2810A Handling Instructions SOFTWARE VERSION ･ Adjust Backlight FAULT CONVERSION ･ With "ADJUST BACKLIGHT", the brightness ANALOG INPUT ･ of the monitor display can be adjusted. ･ Press the right arrow key to make the display Note: brighter. Press the left arrow key to make the "GAGE DATA"...
  • Page 96 GM2810A Handling Instructions Highlight "SET LOW FUEL LEVEL", and Fuel Level then press the Enter key. With "FUEL LEVEL", the low fuel level can be specified. Press the menu key. After the main menu appears, use the SET LOW FUEL LEVEL arrow keys to highlight "UTILITIES", and...
  • Page 97 GM2810A Handling Instructions A warning mark appears in the upper- Low Fuel Level Display right corner of the monitor display. Caution If a warning message appears, immediately stop operation, and then supply fuel. 0 RPM 83 % When the fuel level falls below the...
  • Page 98 GM2810A Handling Instructions Pressing the Enter key changes the screen Fault Code Displays from the fault code to the parameter display. Important Important If the service reminders are configured, the When the fault code (DTC) appears in the notices of the replacement time period for monitor display, contact your dealer.
  • Page 99 GM2810A Handling Instructions Text 2 Text 2 ･ ･ The corrective action appears. The corrective action appears. 1 of 1 WARNING 1 of 1 WARNING SPN 916 FMI 17 SPN 110 FMI 3 CORRECTIVE ACTION: CORRECTIVE ACTION: S e e S e r v i c e M a n u a l S e e S e r v i c e M a n u a l <...
  • Page 100 GM2810A Handling Instructions Engine warning lamp blinks when only DTC Engine Warning Lamp relevant to PCD/NCD come up. Important Make repairs immediately if the fault codes of PCD (Particulate Control Diagnostic) and NCD (NOx Control Diagnostic) appear. Engine warning lamp (LED) lights up or blinks when a failure occurs on the function of engine.

  • Page 101: Travel Of Machine

    GM2810A Handling Instructions Stop the engine. Travel of Machine "Procedure to Stop Engine" (Page 4-22) Moving The Machine Apply the parking brake. Chock the wheels. Caution Secure the machine with ropes. Front left side Under any circumstances drive the machine at such a speed that you can stop it immediately for emergencies.

  • Page 102: Cutting Work

    GM2810A Handling Instructions Pull up the lever behind the seat to unlock it, Cutting Work and then tilt the seat forward to open the cover. Cutting Operation Warning Do NOT start to move or stop the machine abruptly. To do so is very dangerous. In addition, it may damage the hydraulic system or result in oil leakage.

  • Page 103: Transporting

    GM2810A Handling Instructions Note: During the work, the rotary knives will rotate or stop in sync with the up and down motion of the mower decks. Transporting Transporting Procedure When loading the machine into a trailer or a truck to transport it, drive the machine forward.
  • Page 104 GM2810A Handling Instructions Page 4-74 Storage...

  • Page 105: Maintenance

    GM2810A Maintenance Maintenance Precautions ..... Page 5-2 Maintenance Schedule ......Page 5-2 Adjusted Value ........Page 5-7 DPF ............Page 5-8 About DPF ..........Page 5-8 DPF Regeneration ......... Page 5-8 Replacement of DPF ......Page 5-12 Conditions for DPF Regeneration ..Page 5-13 PM Accumulation Level .......

  • Page 106: Maintenance Precautions

    Use tools appropriate for each maintenance operation. Important For the safe and best performance of your machine, use Baroness genuine parts for replacement and accessories. Please note that our product warranty may be void if you use non-genuine parts for replacement or accessories.
  • Page 107 GM2810A Maintenance Maintenance Item Remarks Check tightening bolts 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 and nuts Check brake function 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　...
  • Page 108 GM2810A Maintenance Maintenance Item Remarks Check every 100 hours or Check exterior of every month 　 　 　 　 ○ 　 　 　 　 　 　 　 ○ 　 　 　 　 battery whichever comes earlier Check every 100 hours or...
  • Page 109 GM2810A Maintenance Maintenance Item Remarks Replace fuel filter *1.*4 　 　 　 　 　 　 △ 　 　 　 　 　 　 　 　 　 　 　 cartridge Clean water separator 　 　 　 　 　 　 　 ○ 　 　 　 　 　 　 　 　 　...
  • Page 110 *1: When biodiesel fuel is used, change the fuel filter cartridge, fuel hose and clamp bands with new ･ ones at intervals half of the usual ones. *2: Consult your local Baroness Dealer or local KUBOTA Dealer for this service. ･ Page 5-6...

  • Page 111: Adjusted Value

    GM2810A Maintenance The items above (*3 marked) are registered as emission related critical parts by KUBOTA in the ･ U.S. EPA nonroad emission regulation. As the engine owner, you are responsible for the performance of the required maintenance on the engine according to the above instruction.

  • Page 112: Dpf

    GM2810A Maintenance Automatic Regeneration About DPF Danger Danger The DPF is a purifying filter that collects PM Since it will become extremely hot around the (soot) from exhaust gas. exhaust outlet during DPF regeneration, do When a certain amount of PM (soot) has...
  • Page 113 GM2810A Maintenance Important If the regeneration remains uncompleted even after 30 minutes have passed since the start of automatic regeneration in PM accumulation 2400 RPM 100 % "Level 1", PM accumulation level enters ENG RPM % SOOT 65 C 40 % "Level 2".
  • Page 114 GM2810A Maintenance Park this machine in a safe location. Important Apply the parking brake. If the regeneration remains uncompleted in Set the throttle opening to 0% (idling). automatic regeneration, parked regeneration Press the DPF parked regeneration switch. is required with the blinking regeneration icon.
  • Page 115 GM2810A Maintenance Manual Regeneration Danger Danger 1 of 2 C : 1 Since it will become extremely hot around the SPN 3701 FMI 15 E x c e s s i v e P M 3 exhaust outlet during DPF regeneration, do not perform the regeneration in a location <...

  • Page 116: Replacement Of Dpf

    GM2810A Maintenance ■In PM accumulation "Level 4": Contact your dealer for manual regeneration. Important Replacement of DPF If ignoring the manual regeneration requirement and continuing traveling or cutting When PM accumulates excessively in the DPF work in PM accumulation "Level 4", PM or ash accumulates, replace the DPF since the accumulation level enters "Level 5".

  • Page 117: Conditions For Dpf Regeneration

    GM2810A Maintenance Stop the engine. PM Accumulation Level Contact your dealer for DPF replacement. Level 0 Conditions for DPF Regeneration DPF regeneration is not necessary. Danger Danger Level 1 Since it will become extremely hot around the exhaust outlet during DPF regeneration, do...
  • Page 118 GM2810A Maintenance <Automatic regeneration> <Parked regeneration> ■When the DPF auto regeneration inhibit These are the conditions for activating ･ switch set to the "Auto regeneration mode": parked regeneration. When the conditions for automatic The parking brake is applied. regeneration are met, the automatic The traveling pedal is in neutral.
  • Page 119 GM2810A Maintenance When the regeneration completed, the Level 2 regeneration icon disappears. Danger Danger Since it will become extremely hot around the exhaust outlet during DPF regeneration, do not perform the regeneration in a location 2400 RPM 100 % where fires may occur.
  • Page 120 GM2810A Maintenance <Parked regeneration> Level 3 These are the conditions for activating ･ parked regeneration. Danger Danger The parking brake is applied. Since it will become extremely hot around the The traveling pedal is in neutral. exhaust outlet during DPF regeneration, do The throttle opening is 0% (idling).
  • Page 121 GM2810A Maintenance These are the statuses in PM accumulation Level 4 "Level 3". Danger Danger Since it will become extremely hot around the exhaust outlet during DPF regeneration, do 1 of 2 C : 1 not perform the regeneration in a location...
  • Page 122 GM2810A Maintenance These are the statuses in PM accumulation Level 5 "Level 4". When PM accumulates excessively in the DPF or ash accumulates, replace the DPF since the regeneration in that case is prohibited. ･ You can not continue to use this machine...

  • Page 123: Jacking Up The Machine

    GM2810A Maintenance Jacking Up The Machine Jack-up points 　 Front right frame About Jacking Up The Machine Front left frame Center of pivot Warning Below rear wheel motors When replacing a tire or beginning any other Front right frame maintenance or repairs, be sure to chock the wheels to prevent the machine from moving.

  • Page 124: Greasing

    GM2810A Maintenance Below rear wheel motors Greasing Points Two locations Grease nipples are installed in the following locations. Add grease every 50 hours of operation. rwyt62-032 Jack-Up Points_005 Greasing About Greasing Since there may be adhesion or damage due to lack of grease on moving parts, they must be greased.
  • Page 125 GM2810A Maintenance Rear roller Lift arm fulcrum There is one greasing point each on the left There is one greasing point on the arm and right of each mower deck. connected to each mower deck. Lower the mower decks before greasing the lift arm fulcrums.
  • Page 126 GM2810A Maintenance Lift arm cylinder fulcrum Rear left wheel This is on each cylinder of the arms connected to each mower deck. Mower decks #1, #4 and #5 There are two greasing points on each cylinder. 8bq62b-033 Greasing Points_011 Rear right wheel...

  • Page 127: Maintenance Work

    GM2810A Maintenance Traveling pedal shaft fulcrum Maintenance Work There are two locations. Cleaning of Mower Deck Be sure to clean the mower deck after use. Stop the engine, and then remove the key. Carefully clean the front and back of the mower deck with water or compressed air.
  • Page 128 GM2810A Maintenance Mower Deck #1 Important Before installing the rotary knife, make sure Start the engine, and then raise the mower that it is balanced. decks. Stop the engine, and then remove the key. If the edge of the rotary knife becomes chipped Lift the mower deck at the front.
  • Page 129 GM2810A Maintenance Follow the steps below to remove the rotary Mower Decks #2/#3 knife. Remove the clip pin installed on the mower Use the square pipe from the included arm, and then pull out the grip pin. tools to secure the rotary knife so that it does not turn.
  • Page 130 GM2810A Maintenance Start the engine, and then raise the mower decks. Stop the engine, and then remove the key. Lift the mower deck at the front. to41g1-007 Mower Decks #2/#3_006 Square pipe Rotary knife x9s1w3-005 Bolt Mower Decks #2/#3_004 Spring washer...

  • Page 131: Grinding Of Rotary Knife

    GM2810A Maintenance Remove the cotter pin and hardened Important roundhead pin inserted at a, and then insert them at c. The tightening torque for the knife mounting bolt is 67 - 85 N-m (683.20 - 866.75 kgf-cm). Install the rotary knife.
  • Page 132 GM2810A Maintenance When, after grinding, the blade base of the Grind the cutting edge of the rotary knife. rotary knife does not reach the sail Grind so that the edge angle is 30 - 40 degrees, the point thickness is 0.5 - 1.0 mm (0.02 - 0.04 in), and the blade base does not...

  • Page 133: Balancing Of Rotary Knife

    GM2810A Maintenance Balancing of Rotary Knife Removing/Installing Tires Front Tires Caution Follow the steps below to remove the front The rotary knife is an edged tool. tires: Take extra care in handling since they could Loosen the bolts. cut your hands or legs.

  • Page 134: Adjustment Of Belt Tension

    GM2810A Maintenance Rear Tire Fan Belt Follow the steps below to remove the rear Press the middle of the belt with your finger tire. to check the belt tension. Loosen the bolts. If the belt tension is inappropriate, loosen bolts A and B (that affix the alternator), and then move the alternator to adjust the tension.

  • Page 135: Adjustment Of Brake

    GM2810A Maintenance Adjustment of Brake Adjustment bolt (on brake disc side) Lever Caution Open (neutral) Make sure that the brake wire is not cracked Reduce the clearance by loosening the lock or damaged. nut, then tightening the adjustment nut. Tighten the adjustment nut until the friction...

  • Page 136: Adjusting The Neutral Position Of The Piston Pump

    GM2810A Maintenance With the brake pedal released, obtain a play Break-In of Brakes of 1.0 mm (0.039 in) at the connection of the inner wire. If the brake shoes or brake pads are worn, replace them with new ones. Immediately after replacement, drive to break in the brakes if the effectiveness of the brakes is low.

  • Page 137: Change Of Coolant

    GM2810A Maintenance While pulling up the lever, tilt the seat Change of Coolant upward. Caution Do not touch the radiator or coolant during engine operation or immediately after the engine has been turned off. Otherwise, you may get burned. Caution...
  • Page 138 GM2810A Maintenance Remove the reserve tank. LLC concentration Freezing temperature (volume %) Down to -10 °C (14 °F) 20 % Down to -15 °C (5 °F) 30 % Down to -20 °C (-4 °F) 35 % Down to -25 °C (-13 °F)

  • Page 139: Change Of Hydraulic Oil

    GM2810A Maintenance Open the tank cap, and then pour new oil Change of Hydraulic Oil from the fill port until the oil level reaches the middle of the oil gauge on the hydraulic tank. Caution The hydraulic tank capacity is approximately 44.0 dm...

  • Page 140: Change Of Hydraulic Oil Filter

    GM2810A Maintenance Firmly tighten the filter cartridge by hand Change of Hydraulic Oil Filter until the packing contacts the mounting surface. Change of Hydraulic Oil Line Filter And then tighten it with a half more turn. Caution Be careful with hot oil, which could cause burns if it contacts your skin.

  • Page 141: Change Of Air Cleaner

    GM2810A Maintenance Install the intake hose joint fitting to the Change of Hydraulic Oil Suction Filter hydraulic tank. Caution When replacing the hydraulic oil filter, be sure to drain the oil into a container and discard it in accordance with local laws and regulations.

  • Page 142: Change Of Engine Oil

    GM2810A Maintenance Through the oil filling port, supply new Change of Engine Oil engine oil until the oil reaches a level in between the upper and lower limit lines on Caution the oil level gauge. Engine oil quantity is approximately 9.7 dm Be careful with hot oil, which could cause (9.7 L).

  • Page 143: Replacement Of Engine Oil Filter

    GM2810A Maintenance Make sure that there is no oil leakage at the Replacement of Engine Oil Filter sealing surface of the filter cartridge. Check the engine oil level. Caution If it is low, supply engine oil until it reaches Be careful with hot oil, which could cause the specified level.

  • Page 144: Change Of Fuse

    GM2810A Maintenance rvnnv5-002 pkm25s-010 Replacement of Fuel Filter_002 Fuse Box_001 Cartridge Fuse box Packing The machine uses a mini fuse for Cover automobiles. Air-bleeding plug Replace an old fuse with a new fuse of the specified capacity. O-ring Remove air after replacement.
  • Page 145 GM2810A Maintenance Fusible Link Fuse capacities of the fusible links are 30 A and 50 A. 1qgabk-009 Fusible Link_001 Fusible link (50 A) Fusible link (30 A) Maintenance Work Page 5-41...
  • Page 146 GM2810A Maintenance Page 5-42 Maintenance Work...
  • Page 150 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Fax : +81 - 533 - 84 - 1220 Aichi-pref, 442-8530 JAPAN GM2810A-UM--GBZ/19K-00-S.K E02[GM2810_EU02]...

Table of Contents