Page 3
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE REPLACE THESE COMPONENTS WITH SONY PARTS ANODE. WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. – 2 –...
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 SELF DIAGNOSTIC FUNCTION The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automati- cally begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/ TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 6
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT Diagnostic Item Flash Count* 2 times +B overcurrent/overvoltage 2 times Vertical deflection stopped 4 times 4 times * One flash count is not used for self-diagnostic. Lamp ON 0.3 sec. Lamp OFF 3 sec.
Page 7
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”. Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 The operating instruction mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of SECTION 1 GENERAL the Operating Instruction Manual remain as in the manual. Getting Started Getting Started (KV-HA21M80/H/HA21M81) (KV-HA21M50/HA21M80) Step 1 Step 1 Insert the batteries (supplied) into the remote.
Page 9
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 WARNING TV front and rear panels • Dangerously high voltages are present inside the TV. TV rear panel • TV operating voltage: 110 – 240 V AC. (KV-HA21M50/HA21M80/HA21M80/H/HA21M81) 220-240 V AC. (KV-HA21M60/HA21P52) • Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.
Page 10
• Count the number of times the 1 (standby) indicator flashes. Press ! The 1 (standby) yellow, blue) menu. (main power) to turn off your TV. Contact your nearest Sony service indicator on your TV Reveal concealed center. flashes red several...
Page 11
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 Presetting channels Remote control (KV-HA21M60 only) You can automatically preset up to 100 TV channels in numerical sequence Button Function from program number 1, or manually preset desired channels and channels – Turn off temporarily or that cannot be preset automatically. turn on the TV.
Page 12
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 Presetting channels (continued) (KV-HA21P52) Customizing the picture and sound (continued) Selecting the space sound mode To change the color system setting Press SPACE SOUND. If the color is abnormal when receiving programs through the 8 (antenna input) terminal or the t (video input) terminal Select (1) Press SELECT until “COLOR SYS”...
Page 13
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 Viewing Teletext Enjoying bilingual program KV-HA21M81 only (KV-HA21P52 only) Some TV stations broadcast an information service called Teletext which You can enjoy bilingual program of A2 bilingual system by using the A/B allows you to receive various information, such as stock market reports and button.
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 SECTION 3 RM-969 SET-UP ADJUSTMENTS The following adjustments should be made when a complete Perform the adjustments in the following order : realignment is required or a new picture tube is installed. 1. Beam Landing These adjustments should be performed with rated power 2.
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 3-2. CONVERGENCE • Operation of V. Stat magnet If the V. Stat magnet is moved in the "a" and "b" arrows, the Preparation : red, green and blue dots move as shown below. • Before starting this adjustment, adjust the focus, horizontal size and vertical size.
Page 18
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 (2) Dynamic Convergence Adjustment Preparation: Before starting this adjustment, adjust the horizontal static convergence and the vertical static convergence Insert Correction Plate to DY Pocket (Left or Right) YCH Rotate YCH VOL on DY Rotate TLV VOL ON DY XCV Rotate XCV Adj core on DY ON DY: (3) Screen-corner Convergence...
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 3-3. FOCUS ADJUSTMENT 2.a) WHITE BALANCE ADJUSTMENT 1) Set to Service Mode (Refer Section 4-1: ADJUSTMENTS FOCUS adjustment should be completed before W/B adjustment. WITH COMMANDER). 1. Receive digital monoscope pattern. 2) Input white raster signal. 2. Set "Picture Mode" to "DYNAMIC". 3) Set 49 (ABL) and IF (VP2) service mode to 00.
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 SECTION 4 RM-969 CIRCUIT ADJUSTMENTS 4-1. ADJUSTMENT WITH COMMANDER e. OTHER FUNCTION VIA REMOTE COMMANDER 7, - All the data becomes the values in memory. Service adjustments to this model can be performed using the 8, - All user control goes to the standard state. supplied Remote Commander RM-969 5, - Service data initialization (Be sure not to use...
Page 23
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 ITEM INFORMATION No. 1E VP1 Item KV-HA21M50 KV-HA21M60 KV-HA21M80 (E) KV-HA21M80 (VT) KV-HA21M80/H KV-HA21M81 KV-HA21P52 Switch-on behaviour 1=Switch -on of picture via internal delay 0=Without delay 00(4) 1=Switch off in vertical overscan 0=Switch-off undefind 18(7) Service blanking 1= on 0= off 0B(7) RGB Blanking Mode 1 = wide blanking, 0 = normal blanking 02(7)
Page 24
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 No. 4E OP1 Item HA ME VOL AV Input COMB KV-HA21M50 KV-HA21M60 KV-HA21M80 (E) KV-HA21M80 (VT) KV-HA21M80/H KV-HA21M81 KV-HA21P52 HA ME Vol Tone controller Volume curve setting. 1 = for HA(ME), 0 = for HA(GE) AV Input 00 = no AV Input model 01 = 1 AV Input model 10 = 2 AV Input model...
Page 25
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 OPERATION GUIDE SERVICE MODE How to set up new NVM (or initialize already written one) (1) AC ON (2) Enter Service Mode - describing below how to enter (3) Push the commander button “5” and “0” sequentially (only set initial data into RAM, but not write them into NVM yet) (4) Push the commander button “2”...
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 RM-969 4-3. PICTURE QUALITY ADJUSTMENT 4-4. DEFLECTION ADJUSTMENT NORMAL MODE (50Hz) SUB COLOR ADJUSTMENT Set to Service mode. 1. Select Video. Input PAL color bar. Using the 1 and 4 button, select category GEO 2. Input a PAL color-bar. 3.
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 KV-HA21M80/H/HA21M81/HA21P52 SECTION 5 RM-969 RM-969 DIAGRAMS 5-1. BLOCK DIAGRAM POWER SUPPLY, DEFLECTION, AUDIO CV (RGB AMPLIFIER) Q405 J400 AND VIDEO PROCESSING, BUFFER VIDEO AUDIO/VIDEO INPUT/OUTPUT, SYSTEM CONTROLLER Q404 MONITOR Q712 Q706 BUFFER L (MONO) R DRIVE R AMP Q403 VIDEO BUFFER...
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 KV-HA21M80/H/HA21M81/HA21P52 RM-969 RM-969 5-3. SCHEMATIC DIAGRAM 5-2. CIRCUIT BOARDS LOCATION Note: • All capacitors are in µF unless otherwise noted. • All electrolytic capacitors are rated at 50V unless otherwise noted. • All resistors are in ohms. kΩ...
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 KV-HA21M80/H/HA21M81/HA21P52 RM-969 RM-969 5-6. PRINTED WIRING BOARDS AND PARTS LOCATION PRINTED WIRING BOARDS NOTE: The circuit indicated at left contains high voltage of over [POWER SUPPLY,DEFLECTION, 1220 Vp-p. Please pay attention when inspecting or re- AUDIO AND VIDEO PROCESSING, pairing it to prevent an electric shock.
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 SECTION 6 RM-969 EXPLODED VIEWS NOTE: • • Items marked " ∗ " are not stocked since Items with no part number and no The components identified by description are not stocked because they are seldom required for routine shading and mark ! are critical they are seldom required for routine ser vice.
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. SECTION 7 Replace only with part number specified. ELECTRICAL PARTS LIST REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK • Items marked " ∗ " are not stocked since •...
Page 51
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK C105 1-163-038-91 CERAMIC CHIP 0.1UF C226 1-126-963-11 ELECT 4.7UF 20.00% 50V...
Page 52
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK C318 1-163-038-91 CERAMIC CHIP 0.1UF C357 1-162-964-11 CERAMIC CHIP 0.001UF 10.00% 50V (EXCEPT KV-HA21M60/HA21P52)
Page 53
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK C552 1-137-194-81 FILM 0.47UF 5.00% C866 1-162-974-11 CERAMIC CHIP 0.01UF C554...
Page 54
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK <TRIMMER> D500 8-719-911-19 1SS119-25 D501 8-719-911-19 1SS119-25 CT131 1-767-774-22 TRAP, CERAMIC...
Page 55
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK IC201 8-759-476-86 TDA7438D013TR L103 1-410-987-42 INDUCTOR 0.33UH IC203 6-700-034-01 IC AN5276...
Page 56
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK Q203 8-729-010-25 MSD601-RT1 R016 1-216-815-11 RES-CHIP 1/16W Q204 8-729-216-22 2SA1162-G...
Page 57
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK R074 1-216-821-11 RES-CHIP 1/16W R215 1-216-827-11 RES-CHIP 3.3K 1/16W R076...
Page 58
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK R327 1-216-821-11 RES-CHIP 1/16W R389 1-216-851-11 RES-CHIP 330K 1/16W R328...
Page 59
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK R520 1-216-833-11 RES-CHIP 1/16W R800 1-216-821-11 RES-CHIP 1/16W (KV-HA21M50/HA21M60/HA21M80(E)/ R801...
Page 60
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK C2404 1-163-038-91 CERAMIC CHIP 0.1UF T600 ! 1-431-747-11 TRANSFORMER, LINE FILTER C2405 1-163-087-00...
Page 61
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK L2201 1-410-509-61 INDUCTOR 10UH <CRYSTAL> L2302 1-414-855-31 INDUCTOR L2303 1-414-855-31...
Page 62
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. CV V REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK <COIL> * A-1342-630-A V2 BOARD MOUNTED (KV-HA21M81) ********************* L701 1-414-185-41...
Page 63
KV-HA21M50/HA21M60/HA21M80/ KV-HA21M80/H/HA21M81/HA21P52 The components identified by shading RM-969 and mark ! are critical for safety. Replace only with part number specified. REF NO. PART NO. DESCRIPTION REMARK REF NO. PART NO. DESCRIPTION REMARK <RESISTOR> 4-086-232-12 MANUAL, INSTRUCTION (KV-HA21M60) 4-086-150-11 MANUAL, INSTRUCTION (KV-HA21M80(E)) R5821 1-216-082-00 RES-CHIP...
Page 65
SUPPLEMENT-2 BG2T CHASSIS MODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO. KV-HA21M50 RM-969 Malaysia SCC-U71D-A KV-HA21M60 RM-969 Thailand SCC-U73L-A KV-HA21M80 RM-969 SCC-U68D-A KV-HA21M80 RM-969 Vietnam SCC-U75B-A KV-HA21M80/H RM-969 SCC-U67K-A (DOLPHIN GRAY) (BLACK) KV-HA21M81 RM-969 SCC-U67J-A KV-HA21P52 RM-969 Thailand SCC-U73K-A SUBJECT : CHANGE COLOR FOR THAILAND MODELS Note: The following change will be applied from Apr.
Page 66
PART NO. DESCRIPTION REMARK X-4041-740-01 BEZNET ASSY 2,27,28 (KV-HA21M60/P52) X-4041-741-01 DOOR ASSY, CONTROL (KV-HA21P52) X-4041-742-01 DOOR ASSY, CONTROL (KV-HA21M60) X-4041-758-01 COVER ASSY, REAR (KV-HA21M60/P52) Sony Corporation Sony Technology Malaysia Sdn. Bhd. English 9-872-274-03 Visual Products 2003.5 – 73 –...