Advertisement
Quick Links
LED Light Kit
2012 and After Greensmaster
Model No. 04294
This product contains a chemical or chemicals known to the State of California to
Important: Ensure that you have installed the Light Kit and Hour Meter Wire Harness Kit for 2012 and After (Model
04295) before you install the LED light kit.
Note: Determine the left, right, front, and back sides of the machine from the normal operating position.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Right light-bar strap
Spacer
Flange-head bolt (3/8 x 1-1/4 inches)
Left light-bar strap
Flange-head bolt (5/16 x 1 inch)
Washer (5/16 inch)
Flange locknut (5/16 inch)
Spring post (1-3/4 inches)
Screw (5/16 x 2-3/4 inches)
LED light
Harness
Shield
Cable tie
No parts required
No parts required
Register at www.Toro.com.
®
800, 1000, and 1600 Series Mower
WARNING
CALIFORNIA
Qty.
–
1
4
4
1
2
2
2
1
1
2
1
2
7
–
–
Form No. 3402-210 Rev A
Installation Instructions
Use
Prepare the machine.
Install the light bar to the machine.
Assemble the LED lights to the light bar.
Install the wire harness to the machine.
Connect the spark-plug wire.
Original Instructions (EN)
All Rights Reserved *3402-210* A
Printed in the USA
Advertisement
Related Manuals for Toro 04294
Summary of Contents for Toro 04294
- Page 1 Form No. 3402-210 Rev A LED Light Kit 2012 and After Greensmaster ® 800, 1000, and 1600 Series Mower Model No. 04294 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
-
Page 2: Preparing The Machine
Preparing the Machine Installing the Light Bar to the Machine No Parts Required Parts needed for this procedure: Procedure Right light-bar strap 1. Ensure the reel drive engagement lever is in the Spacer position; refer to the Operator’s REEL DRIVE Flange-head bolt (3/8 x 1-1/4 inches) Manual. - Page 3 Figure 3 Figure 2 1. Kickstand 5. Existing screw (5/16 x 2 inches) 1. Kickstand 5. Side plate 2. Flange nut 6. New spring post (1-3/4 2. Locknut 6. Screw (5/16 x 1 inch) inches) 3. Washer 7. Spring post (1 inch) 3.
- Page 4 7. Assemble the spring-anchor bracket, right light-bar strap, 2 spacers, and right-side plate to the outer pad of the rear frame (Figure 5) with the 2 flange-head bolts (3/8 x 1-1/4 inches) and 2 lock washers (3/8 inch) that you removed in step 6. Figure 6 1.
- Page 5 11. Ensure that the hook of the spring is inserted through hole in the spring-anchor bracket. 12. Seat the free end of the spring onto the spring post of the kickstand (A of Figure 13. Attach the kickstand to the side plates with the locknuts, washers, spacers, and screws (5/16 x 1 inch) that you retained in step (B of...
- Page 6 Assembling the LED Lights to the Light Bar Parts needed for this procedure: LED light Harness Shield Cable tie Assembling the Wire Harness to the LED Light Fixtures 1. Connect the 2-pin of the LED light into the 2-socket connector of the LED light harness (Figure 10).
- Page 7 Assembling the LED Light Fixtures to the Light-Bar Straps 1. Align the light fixtures with the lenses of the lights toward the front of the machine (Figure 12). Installing the Wire Harness to the Machine No Parts Required Procedure 1. Route the wire harness for the LED light kit down the left light-bar strap and across to the left handle-bar tube (Figure...
- Page 8 Connecting the Spark-Plug Wire No Parts Required Procedure Connect the spark-plug wire to the terminal of the spark plug; refer to Figure 1 1 Preparing the Machine (page Figure 14 1. 2-socket connector (wire 3. Console harness—LED light and wireless hour meter harness kit) 2.