Advertisement
Quick Links
Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly maintained, give years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
7 Ensure all workshop safety rules, regulations, and conditions are complied with when using torque wrench.
3 Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine
parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
7 The wrench is a precision tool, DO NOT abuse it. DO NOT drop or throw the wrench.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
WARNING! DO NOT use the wrench if damaged or thought to be faulty (contact Service Agent).
p
p
7 DO NOT use wrench unless you have been instructed in its use by a qualified person.
7 DO NOT use any cleaner which might affect the high pressure grease with which the wrench is packed.
3 After use adjust to lowest torque setting (but not below),clean and store in a safe, dry, childproof location.
2.
INTRODUCTION & SPECIFICATIONS
2.1. Introduction
These torque wrenches are precision tools and each is supplied with a calibration certificate. Torque setting is by means of a micrometer type adjuster and the drive
head has a reversible ratchet.
2.2. Specifications
Torque Range (Nm) . .5-25 . . . . . . .7-112 . . . . . .40-210 . . . .70-420 . . . . .140-700 . . . . . .20-80 . . . . . .30-210 . . . . .50-560
Alternative Scale . . . .44-221lb.in . .5-83lb.ft . . . .30-155lb.ft . .52-310lb.ft . .103-516lb.ft . . .20-110lb.ft . . .20-150lb.ft . .50-400lb.ft
Drive (sq) . . . . . . . . .1/4” . . . . . . .3/8” . . . . . . .1/2” . . . . . . .3/4” . . . . . . .3/4” . . . . . . . . . .3/8” . . . . . . . .1/2” . . . . . . .3/4”
Length (mm) . . . . . . .275 . . . . . . .370 . . . . . . .460 . . . . . . .850 . . . . . . .1070 . . . . . . . . .405 . . . . . . . .535 . . . . . . .675
3.
OPERATION
3.1. Hold torque wrench in left hand (if right handed) so that
required scale - on shaft, just above hand grip - is uppermost
and visible.
3.2. Turn the lock screw, in the end of the grip, anticlockwise to unlock
grip (STW201 has a locking plug in the end of the grip - pull ring
to unlock).
3.3. Turn grip to select torque setting as follows:
• Required setting - 56Nm
• Turn grip until top edge is level with the 50Nm line on the shaft
scale and the ‘zero’ on the grip graduation is aligned with the
centre line of the shaft scale.
• Rotate the grip further, clockwise, until the ‘6’ on the grip
graduation is aligned with the centre line to give a setting of 50
+ 6 = 56Nm, lb.m, lb.ft or kg.m.
Note: If using the alternative scale ( in.lb, ft.lb or m.kg depending
on wrench) then each division of the grip graduation is equivalent
to the scale increment divided by the number of divisions. For
example (STW1011):
The alternative scale is in lb.ft.
Scale increments are 5.16lb.ft
There are 7 grip divisions.
Then each division is 5.16/7 = 0.74lb.ft
3.4. Tighten lock screw at end of handle to prevent accidental
alteration of the setting.
3.5. When tightening the nut/bolt you will feel and hear the wrench
mechanism click when the set torque is reached. Immediately stop
applying force to wrench to avoid over-tightening the nut/bolt.
Wrench will reset ready for the next application.
Note: If wrench is not used for some while, operate it a few times,
at a low setting, to ensure all internal parts are coated in grease.
4.
RECALIBRATION
To ensure continued accuracy the wrench should be recalibrated
annually and after any impact or other misuse. Contact
an NAMAS accredited laboratory.
5.
CALIBRATION CERTIFICATE
See over for the Calibration Certificate for this wrench.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
01284 757500
STW101
STW1011
STW102
Pounds
Feet
(lb.ft)
Sole UK Distributor,
Sealey Group, Bury St. Edmunds, Suffolk.
01284 703534
INSTRUCTIONS FOR:
STW101, ST W 1 0 11 , S T W 1 0 2 ,
Models:
STW103, STW104, STW200,
STW201 & STW202
STW103
STW104
Kilogram
Newton
Newton
Pounds
Metres
Metres
Metres
Feet
(kgm)
(Nm)
(Nm)
(lb.ft)
sales@sealey.co.uk
e-mail
STW101, STW1011, STW102, STW103, STW104, STW200, STW201, STW202 - 1 - 271004
T O R Q U E W R E N C H E S
IMPORTANT: No liability is accepted for incorrect
use of this equipment. WARRANTY: Guarantee is
12 months from purchase date, proof of which will
be required for any claim. INFORMATION: For a
copy of our latest catalogue and promotions call
us on 01284 757525 and leave your full name and
address, including postcode.
STW200
STW201
STW202
Kilogram
Kilogram
Newton
Metres
Metres
Metres
(kgm)
(kgm)
(Nm)
www.sealey.co.uk
Web
Pounds
Feet
(lb.ft)
Advertisement
Related Manuals for Sealey STW101
Summary of Contents for Sealey STW101
- Page 1 STW201 & STW202 Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly maintained, give years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 TORQUE WRENCH CALIBRATION CERTIFICATE STW101, STW1011, STW102, STW103, STW104, Models: STW200, STW201 & STW202 STW101, STW1011, STW102, STW103, STW104, STW200, STW201, STW202 - 1 - 271004...
- Page 3 16.6 46.1 49.92 83.2 76.8 STW202 107.5 116.5 322.6 349.4 537.6 582.4 Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk. 01284 757500 01284 703534 www.sealey.co.uk sales@sealey.co.uk e-mail STW101, STW1011, STW102, STW103, STW104, STW200, STW201, STW202 - 1 - 271004...