Table of Contents
Advertisement
Available languages
Available languages
6 HEAT SETTINGS THAT GIVE YOU CONTROL OF YOUR COMFORT
Once your heater is ON, use the control buttons on the front panel to select the desired heat setting for your
needs. Your heater will start on the Constant Hi Room heat setting each time you turn the heater on. Here is
a handy reference to help select the heat option that best suits your desired comfort level:
FLOOR AREA – (LOW HEAT)
This setting uses the lower level heating element only to provide a comfortable, gentle heat to warm up the
floor area in front of the heater.
PERSONAL – (MODERATE HEAT)
This setting uses a moderate heat level to warm you personally. The LO option (
using the upper level heating elements only, while the HI option (
you to adjust to your desired comfort level.
ROOM – (MODERATE-HIGH HEAT)
Best for whole room heating, use this setting to bring warmth to cooler, drafty rooms. The LO option
provides a moderate heat level, while the HI option uses maximum heat output to create a warmer
environment.
THERMOSTAT – (MODERATE-HIGH HEAT)
To set the Thermostat, press the Thermostat Control Buttons (
Temperature. The Desired Temperature will flash five times and then the Current Temperature in the room
will display as a steady number. The Thermostat can operate on either HI or LO heat levels to achieve
Desired Temperature by pressing the ( ) button under Room.
NOTE: If the Current Temperature is higher than your Desired Temperature, the heater will go into cool down
mode and then shut-off until the room temperature falls below this setting or until the Desired Temperature
is changed.
HEATPHASE™ TIMER
The new HeatPhase
Timer is an auto-off feature that gradually transitions the room temperature from
TM
warmer to cooler. The timer starts at high heat and steps down 4 different heat levels until it shuts off - over
a 2 hour period. This feature is ideal for setting a comfortable, relaxing environment. (Fig. 2) The timer can
also be toggled to start at your desired level.
QUIET MODE
The new Quiet Mode features uses a low heat setting and fan speed to produce a gentle "white noise" and
soothing warmth. This setting uses an upper level heating element only. (Fig. 3)
Fig. 2
2 Hour
Auto-off
Timer with
30 Minute
Phased
Intervals
4
) provides a soothing heat
) slightly increases heat output, allowing
) to choose your Desired
Fig. 3
Gentle Heat
"White Noise"
Setting
SAFETY FEATURES
The Honeywell HeatGenius
Ceramic Heater is equipped with several devices and features for
TM
added protection:
• A four way tip-over switch that disables the heater if it is accidently tipped in any direction. If tipped over,
the unit should be set upright and follow the OPERATION instructions.
• A high temperature safety control prevents overheating. If activated, unplug the device and wait at least
10 minutes for unit to cool. Then plug the heater back in and follow the OPERATION instructions.
• The heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater should
it operate at a higher than normal temperature. If activated, the unit will need to be replaced.
• This heater was created using high quality, heat-resistant plastics and has a Cool Touch handle.
FAHRENHEIT TO CELSIUS
• Press and hold both Thermostat Control Buttons (
and Celsius and back.
CLEANING AND STORAGE
It is recommended that the Honeywell HeatGenius
before off-season storage.
• Turn Off ( ) and unplug heater. Allow unit to cool.
• Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES,
POLISHES OR ANY CHEMICAL SOLUTION.
• Before storing, clean the Ceramic Heater using the above-mentioned steps. Wrap the cord around the
unit. Place in its original box and store it in a cool, dry place.
• This heater does not disassemble.
TROUBLESHOOTING
Problem
Solution
• Be sure it is plugged in and that the electrical outlet is working.
If your Honeywell HeatGenius
TM
Ceramic Heater shuts off
• Check for any obstructions. If you find an obstruction, turn the heater
unexpectedly or fails to
OFF ( ) and unplug it.
operate, one of your heater
• Allow the heater to cool completely, then remove the obstruction,
safety features may have
ensuring that the heater has not been damaged in any way. Wait
been activated to prevent
at least 10 minutes, then re-plug the heater in and follow the
overheating.
OPERATION instructions.
PRODUCT SPECIFICATIONS
Model(s)
Unit dimensions
HCE840 Series
10.2" L x 7.0" W x 17.5" H
HCE845 Series
10.2" L x 7.0" W x 19.5" H
) for three seconds to change between Fahrenheit
Ceramic Heater be cleaned at least once a month and
TM
Amps
Unit
Max
Voltage
Watts
12.5
120V, 60Hz
1500
12.5
120V, 60Hz
1500
Max BTUs
5118
5118
5
- Quick Links:
- Operation
- Troubleshooting
Hide quick links:
Advertisement
Table of Contents
