Advertisement
Quick Links
Electric Lift Kit
Workman
Model No. 07143—Serial No. 404500001 and Up
Model No. 07144—Serial No. 404500000 and Up
Note:
Reuse any mounting hardware that you removed and is not replaced with hardware from the kit.
Preparing the Machine
1.
Park the machine on a level surface (box A of
2.
Engage the parking brake (box B of
3.
Shut off the engine and remove the key (box C of
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
GTX Utility Vehicle
Figure
Figure
1).
Figure
Figure 1
Register at www.Toro.com.
1).
1).
Original Instructions (EN)
All Rights Reserved *3430-965* A
Printed in the USA
Form No. 3430-965 Rev A
Installation Instructions
g038447
Advertisement
Related Manuals for Toro Workman 07143
Summary of Contents for Toro Workman 07143
- Page 1 Engage the parking brake (box B of Figure Shut off the engine and remove the key (box C of Figure g038447 Figure 1 © 2019—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3430-965* A 8111 Lyndale Avenue South Printed in the USA...
- Page 2 Placing the Bed into the Service Position Note: If the draw bar is installed on the machine, you must remove it before placing the bed into the service position. Insert the prop rod into the service position (Figure g036022 Figure 2...
- Page 3 Installing the Lift Bracket Remove the existing bolt and nut from the rear-frame tube (box A of Figure Note: Discard the bolt and nut. Remove the 2 existing plastic rivets from the rear-frame tube (box B of Figure Note: Retain the 2 plastic rivets. Install the lift bracket to the rear-frame tube using the 5 flange-head bolts (3/8 x 2-1/2 inches) and 5 flange nuts (3/8 inch) as shown in box C of Figure...
- Page 4 Installing the Lift Latch Remove the 2 existing bolts from the cargo bed lever (box A of Figure Install the lift latch to the cargo bed lever using the 2 previously removed bolts, and torque the bolts to 15 to 16 N∙m (11 to 12 ft-lb) as shown in box B of Figure g035996 Figure 4...
- Page 5 Installing the Lift Plate Remove the 6 existing bolts and bed braces from the cargo bed (box A of Figure Note: Discard the bolts and bed braces. Install the lift plate to the cargo bed using the 6 bolts, and torque the bolts to 15 to 16 N∙m (11 to 12 ft-lb) as shown in box B of Figure g035960...
- Page 6 Installing the Actuator Stop Electric Machine Only Install the actuator stop to the battery tray mounting bracket using the bolt and nut (Figure g035998 Figure 6 Electric Machine Shown...
-
Page 7: Installing The Fuse
Installing the Fuse Install the fuse (15 A) into the fuse block (Figure Figure Figure 9, and Figure 10). For Kit Model 07143 with Machine Serial Number 403448000 and Before g282494 Figure 7... - Page 8 For Kit Model 07144 with Machine Serial Number 403446000 and Before g282496 Figure 8 For Kit Model 07143 with Machine Serial Number 403448001 and After g282493 Figure 9...
- Page 9 For Kit Model 07144 with Machine Serial Number 403446001 and After g282495 Figure 10...
-
Page 10: Installing The Switch
Installing the Switch Remove the plastic cover from the dashboard (box A of Figure 11). Note: Discard the plastic cover. Install the switch connector through the opening in the dashboard (box B of Figure 11). Install the switch to the switch connector (box C of Figure 11). - Page 11 Installing the Lift Cylinder Important: Use the cable tie to secure the lift-cylinder wire to the wire harness, away from sharp or moving parts. Ensure that you allow enough slack in the wire harness for its full range of motion. Install the lift cylinder using a clevis pin and hairpin cotter (box A of Figure 12).
- Page 12 Important: Use a block to support the lift cylinder so that it extends upward at a 45° angle. g185788 Figure 13...
- Page 13 Removing the Prop Rod Assembly Remove the 2 bolts (3/8 x 2-1/2 inches), 2 flange nuts (3/8 inch), and 3 bolts (5/16 x 3/4 inch) from the prop rod assembly, and remove the prop rod assembly (Figure 14). g036807 Figure 14...
-
Page 14: Operation
Operation Important: Driving the machine with the cargo bed raised may cause the machine to tip or roll easier. The bed structure may become damaged if you operate the machine with the bed raised. • Operate the machine only when the cargo bed is down. •... - Page 15 Raising and Lowering the Bed Important: Unlock the bed latch when using the electric lift to raise and lower the bed. Press upward on the switch to raise the bed (Figure 16). Press downward on the switch to lower the bed (Figure 16).
- Page 16 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.