COLOR TELEVISION RECEIVER Chassis : K15B Model : AG20400SC/TCE TFK20400SC/TCE TFK20506SC/TCE COLOR TELEVISION RECEIVER CONTENTS Precautions Specifications and IC Data Disassembly and Reassembly Alignment and Adjustment Troubleshooting Exploded View and Parts List Electrical Parts List Block Diagram PCB Layout Diagram...
Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing (READING SHOULD protective shields.
Page 4
Precautions 1-1 Safety Precautions (Continued) 9. High voltage is maintained within specified 15. Observe the original lead dress, especially limits by close-tolerance, safety-related near the following areas: Antenna wiring, components and adjustments. If the high sharp edges, and especially the AC and high voltage exceeds the specified limits, check voltage power supplies.
Page 5
Precautions 1-2 Servicing Precautions Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1.
Page 6
Precautions 1-3 Precautions for Electrostatically Sensitive Devices (ESDs) 1. Some semiconductor (Òsolid stateÓ) devices 5. Use only a grounded-tip soldering iron when are easily damaged by static electricity. Such soldering or unsoldering ESDs. components are called Electrostatically Sensitive Devices (ESDs); examples include 6.
Specifications and IC Data 2. Specifications and IC Data 2-1 Specifications Television System 14”/20” NTSC, PAL M/N Color TV Signal Power Consumption 14” : 57 Watts Nominal, 20” : 70 Watts Nominal Picture Tube 14” : A34KQV42X 20” : A48KRD82X (H) Power Requirements AC 100 ~ 240V, 50/60Hz Operating System...
Page 8
Specifications and IC Data 2-2 IC Line Up Table 2-1 IC Line-up Loc. No Specification Description Remark IC201 TDA8841 SI NTSC, PAL M/N Philips IC301 TDA8356 VERTICAL OUTPUT IC501 TDA6107Q RGB DRIVE AMP IC601 LA4425 SOUND-AMP (2.5W x 1CH) IC602 LA4425 SOUND-AMP (2.5W x 1CH) IC801...
Page 9
Specifications and IC Data 2-3 Semiconductor Base Diagrams ELECTROLYTIC- CONDENSER DIODE TDA884X(Pin 56) SSM-174PT(Pin 42) X24CO2P(Pin 8) KS24C020(Pin 8) TRANSISTOR SAW-FILTER TRANSISTOR M1963M 2SD1651 UPC574J 2SD1650 KSD5072 KSC815-Y KA33V KSD5071 KSA539-Y KSD1711 BC548 KSC5386 KTC9014 E B C TRANSISTOR TDA8133 TDA8356 KSR1012 TDA6107Q...
Disassembly and reassembly 3. Disassembly and Reassembly 3-1 Back Cover Removal 1. After removing the screws, press the tension rib and pull the cabinet backwards. 2. To reassemble, press the tension rib (see diagram).
Page 11
Disassembly and reassembly 3-2 Main Board Removal 1. Separate the socket board from the CRT neck. 2. Remove the Anode Cap from the CRT. 3. Remove the main board by pulling it with both hands. Warning: The FBT is charged with high voltage. Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board.
Page 12
Disassembly and reassembly 3-3 Speaker Removal 1. Remove the speaker by pressing the tension rib. 1. Remove the screws. 2. Remove the speaker by pressing the tension rib.
Page 13
Disassembly and reassembly 3-4 CRT Removal 1. Spread a soft mat on the floor. Place the TV set face down. 2. Remove the 4 nuts mounting the CRT to the front cabi- net. Lift the CRT. 3. Caution: Because of the high vacuum and large surface area of the picture tube, be careful while handling it: (1) Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck.
Alignment and Adjustments 4. Alignment and Adjustments 4-1 Preadjustment 4-1-1 Factory Mode 4-1-3 When CRT Is Replaced 1. Make the following adjustments AFTER set- 1. Do not attempt these adjustments in the Video ting up after setting up purity and conver- Mode.
Page 15
Alignment and Adjustments 4-2-2 Main Adjustment Parameter Table 4-1 Main Adjustment Parameter (SSM-174PT, TDA8841) RANGE INITIAL DATA REMARK FUNCTION OSD ABBREVIATION 0 ~ 63 STEP AUTO GAIN CONTROL 0 ~ 128 STEP VOLTAGE CONTROL OSCILLATOR SUB BRIGHT 0 ~ 23 STEP 0 ~ 23 STEP SUB CONTRAST RED DRIVE GAIN...
Page 16
Alignment and Adjustments 4-2-3 Option Table < VIDEO MUTE> 0 : VIDEO MUTE ON 1 : VIDEO MUTE OFF < BLUE-SCREEN OPTION> 0 : BLUE-BACK ON 1 : BLUE-BACK OFF <AUTO SOUND OPTION> 0 : AUTO SOUND OFF 1 : AUTO SOUND ON <...
Page 17
Alignment and Adjustments 4-3 Other Adjustments 4-3-1 General 4-3-2 Automatic Degaussing 1. Usually, a color TV needs only slight touch- A degaussing coil is mounted around the pic- up adjustment upon installation. Check the ture tube, so that external degaussing after basic characteristics such as height, horizontal moving the TV should be unnecessary.
Page 18
Alignment and Adjustments 4-3-4 FOCUS Adjustment 4-3-6 Purity Adjustment 1. Warm up the receiver for at least 20 minutes. 1. Input a black and white signal. 2. Plug in the CRT deflection yoke and tighten 2. Adjust the tuning control for the clearest pic- the clamp screw.
Page 19
Alignment and Adjustments 4 Pole Magnet 2 POLE PURITY 2 Pole Magnet 6 Pole Magnet Clamper Screw ADJUST THE ANG (VERTICAL LINES) YOKE CLAMP SCREW 6 POLE CONVERGENCE 4 POLE CONVERGENCE Fig. 4-2 Convergence Magnet Assembly Vertical Green Belt 31m/m Fig.
Page 20
Alignment and Adjustments 4-3-8 Center Convergence Adjustment 5. Turn the both tabs at the same time, keeping 1. Warm up the receiver for at least 20 minutes. the angle constant, and superimpose the red and blue horizontal line in the center of the 2.
Page 21
Alignment and Adjustments 4-3-10 RF AGC Adjustment 3. Adjust with PHS/NHS (Horizontal Shift) so that the lion-head pattern and CRT centers are aligned. Set the AGC data to 5.0 (Factory Mode). 4-3-11 Sub-Color Adjustment Set SCR data to 10 (Factory Mode). 4-3-12 Geometry Adjustment SC ®PSL (NSL)®PVS (NVS)®...
Page 22
Alignment and Adjustments 4-2-3 Test Pattern (Aging Mode) 1. This mode can be used during servicing, or for confirming that the convergence and purity adjustments are correct. 2. Access the Test Pattern parameters by pressing a CHANNEL keys ( , ) while the Service Mode is on.
Troubleshooting 5. Troubleshooting 5-1 No Video (Raster On, No Sound) Open the IF Pin of Tuner Measure the Check/Replace Voltage of Each Pin TU01, of TU01 Check IC901 Check/Replace Pins 39, 40 IC901, IC201 See "No Sound" See "No Video" (Video OK) (Sound OK)
Page 24
Troubleshooting 5-2 No Power Check/Replace Check the 125V, IC801, D807,D808, 13.0V B + Lines D809,D810,D802 Check/Replace Check IC802 IC802 (KA7630) Pin 9 (5V) Check IC901 Check/Replace Pin 10(4V). IC901, D902 Check IC901 Check/Replace Pin 20 ; Stand-by : 0V IC901, (m-com). Normal : 5V Check/Replace Check IC201,...
Wiring Diagram 10. Wiring Diagram POWER CORD CRT PCB CN501B 1 2 3 4 5 6 7 8 CN701 SOUND L IN SOUND L OUT SOUND R IN SOUND R OUT CN602 FRONT VIDEO IN L + OUT L - OUT 21 PIN VIDEO IN R - OUT R + OUT...
11 Schematic Diagrams 11-1 MAIN 1/4 W 2 @ @ 6 X e ? @ @ ? 7 @ e B 1 e ? @ @ L @ @ e ? @ ? @ @ @ @ @ e ? W 2 @ 6 X e ? @ @ @ @ 6 X ? e @ @ @ @ 6 X e ? W 2 @ 6 X g ? @ 5 ? ? @ @ ? ? @ @ ? @ @ @ @ @ ? @ ?
Page 49
11-2 MAIN 2/4 TP12 TP10 TP14 TP13 W 2 @ @ 6 X e ? @ @ ? 7 @ e B 1 e ? @ @ L @ @ e ? @ ? @ @ @ @ @ e ? W 2 @ 6 X e ? @ @ @ @ 6 X ? e @ @ @ @ 6 X e ? W 2 @ 6 X g ? @ 5 ? 3 @ f ? N @ @ f W &...
Page 50
11-3 MAIN 3/4 TP 16 TP 17 W 2 @ @ 6 X e ? @ @ ? 7 @ e B 1 e ? @ @ L @ @ e ? @ ? @ @ @ @ @ e ? W 2 @ 6 X e ? @ @ @ @ 6 X ? e @ @ @ @ 6 X e ? W 2 @ 6 X g ? @ 5 ? ? @ @ ? ? @ @ ? @ @ @ @ @ ? @ ?