Page 1
COLOR TELEVISION RECEIVER Chassis : K56B Model: CT721APX/XAX COLOR TELEVISION RECEIVER CONTENTS Precautions Reference Information Specifications and IC Data Alignment and Adjustments Troubleshooting Exploded Views and Parts List Electrical Parts List Block Diagrams Schematic Diagrams...
Page 3
7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for STATIC FOCUS VR maximum clarity. DYNAMIC FOCUS VR 8. Repeat 4-7, if necessary. SCREEN <FBT FOCUS PACK> Samsung Electronics...
Page 4
4 to 5 minutes after plugging in the EEPROM. 2. Set DATA LEVEL to 32. Note: M30 TOT adjustment is not done on this chassis. 3. After replacing IC902 EEPROM, input standard data for all items before adjusting GEOMETRIC, WHITE BALANCE, B-CONTRAST, PIP CONTRAST, and SUB-BRIGHTNESS. Samsung Electronics...
Page 5
± 3 H /L 2 62 2 64 50 F L - CT-29A5PX BYTE 1 : 60 - CT-29A6PX BYTE 2 : 02 ± 5 L /L 2 50 2 50 1.4 5 F L ALL model Samsung Electronics...
Page 6
So, all adjustment values when servicing should be readjusted. 2. After IC902 is replaced, connect the AC power supply cord. 3. Turn the power switch ON. 4. In stand-by, warm up the TV for at least 10 seconds. 5. Power on the TV. Samsung Electronics...
Page 7
4-12 MICOM 4-12-1 Description The MICOM used for this K56B Chassis is made by ZILOG (USA). But Samsung have ordered and installed appropriate soft programs in it. 4-12-2 Precaution 1. In power stand-by, apply power supply to only MICOM and E PROM.
Page 8
3. Use the Channel Up/Down ( / ) buttons to move the cursor on the adjustment parameters. Note : 1. When CRT, EEPROM, FBT, or MICOM is replaced, the adjustment values should be controlled. 2. After the Factory Adjustment is completed, be sure to reset the TV set. Samsung Electronics...
Page 9
ADJUSTS THE VERTICAL BLANK WIDTH OF 16:9 SCREEN 0 ~ 1 H BLK WIDTH ADJUSTMENT ON/OFF 16:9 SCREEN 0 ~ 1 ADJUSTS THE LEFT BLANK WIDTH OF 16:9 SCREEN 0 ~ 1 ADJUSTS THE RIGHT BLANK WIDTH OF 16:9 SCREEN Samsung Electronics...
Page 10
AFC LOOP GAIN CONTROL CHROMA TOT BAND SWITCHING SWITCH 0~63 SHARPNESS ADJUST INPUT LEVEL SWITCHING SWITCH TDA9177 0~63 HORIZONTAL FREQUENCY INPUT SELECT SWITCH NO FUNCTION CONTINUOUS TOOTH PATH FILTER SELECT SWITCH (FIXED) 0~63 STEPNESS ADJUST 0~63 LINE WIDTH ADJUST SWITCH Samsung Electronics...
Page 11
ENABLE (Auto OFF op.) FUNCT IO N RE MA R BY T E: 01 NA ME 3D-com b DIS A BLE ENA B LE 4-17 Option Byte MODEL CT-29A6PX REMARK OPTION -SHARP CENTER 50 BYTE 00 BYTE 01 -COMB FILTER "2D" Samsung Electronics...
Page 12
V SIZE (VH) (HA) H SIZE V SHIFT (VS) H SHIFT (HS) (HPC) S CORRECTION (VSC) PIN AMP TILT (HPP) V LINEARITY (VLN) UPPER CORNER PIN (HVC) V BOW (HAB) (HAA) V ANGLE (HLC) LOWER CORNER PIN 4-10 Samsung Electronics...
Page 13
MC4558C 25V- A IC07 IC101 IC106 9V- A H003 SI3050C KA78R12 STA801M 3D- COMB 5VDD 9VDD I C105 KA7805 IC03 S I3 050C T101 H001 I C103 H008 BS - TUNER MAIN-TUNER BS- MICOM BS BL OCK VDD Samsung Electronics...
Page 14
30V- A F TR- 25A004 F BT IC301 L A7845 14. 5V- A VERTICAL - 14. 5V OUTPUT 6. 8V- A HEATER 25V- A CNP03 TO MAIN ASS'Y CNP02 TO MAIN ASS' Y CNP06 TO BS ASS' Y Samsung Electronics...
Page 15
OSD- B moni t or R MONITOR OSD- R OSD- G INPUT 1 OSD- R OSD- G INPUT 2 OSD- B S- VI DEO( Y) I I C S- VI DEO( C) QV01 I I C MONITOR A539 Samsung Electronics...
Page 16
Check Abnormal Check/Replace Check the voltage the voltages of CRT Drive IC05 of Tuner (220V) Normal Check the signal Abnormal Normal Check/Replace input to IC501 Pin 20, Check the voltage 22,24 R/G/B output to CRT of Tuner Cathode Samsung Electronics...
Page 17
Q112 ~ 113 and Buffer short/open Check Check Abnormal Check the output of video the video signal at signal at CNM07 Open Test Q104 TR Normal Check Abnormal the video output BS-Monitor-Out Open Test signal at CNM07 6P Normal Check JAS01 BS-Monitor-Out Samsung Electronics...
Page 18
35 and the Hold "H" of pin 49 Check/Replace IC901 Normal Check Abnormal IC901 Pin 1 (Low when power On) Check/Replace the Power Q806 Normal Abnormal Check the voltage of TB01 Coil Pin 20 Check/Replace Q806 Normal Check the voltage of tuner Samsung Electronics...
Page 19
Pin 17 and the SDA of Pin 18 Check/Replace CNP11 Normal Check Abnormal IC103 Pin 42, 41 I2BUS Control"H" Check/Replace IC102 Normal Check Abnormal the voltage of IC104 3, 4 Pin Check/Replace IC104 Normal Check the voltage of tuner Samsung Electronics...
Page 20
Check Q602 to IC602 Pin 2, 4 Normal Normal Check/Replace IC602 and Check Pin 5 Abnormal Check Check 30V CNM08 Audio (Pin 3) Output Normal Abnormal Normal Check the signal Check/Replace Check/Replace output from Speaker Speaker IC602 Samsung Electronics...
Page 21
Check/Replace IC401 5-7 No Color Check the Abnormal Abnormal Signal input to ICV01 Check H011 Pin 7 Check/Replace H011 Pin 35 Normal Abnormal Check Check/Replace IC501 Pin 5 ICV01 and H003 Normal Check IC501 Pin 20, 22, 24 Samsung Electronics...
Page 22
? @ H ? e ? @ @ ? @ ? h @ ? @ @ e ? @ e @ ? @ ? g @ ? @ ? g @ ? ? @ @ ? @ ? f @ ? @ @ : Power Line : Signal Line Samsung Electronics...
Page 23
? @ @ ? ? @ @ ? ? @ @ ? @ @ @ @ ? @ @ ? ? V 4 @ @ ? @ @ @ @ ? @ @ ? ? @ @ ? ? @ @ ? ? V 4 @ 0 Y e @ @ e @ @ e @ @ TP 4 : Power Line : Signal Line Samsung Electronics...
Page 34
Heed the high voltage limits. These include not exceed 0.5 milliamp. Reverse the power- the XÐray Protection Specifications Label, and plug prongs in the AC outlet and repeat the the Product Safety and X-ray Warning Note on test. the service data schematic. Samsung Electronics...
Page 35
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. Samsung Electronics...
Page 36
Make sure that the portion around the serviced part has not been damaged. 8. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last. Samsung Electronics...
Page 37
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
Page 38
UHF CH: 14 ~ 69 CATV : 1 and 14 ~ 125 CH Antenna Input Range 75 ohm Unbalanced Picture 45.75MHz Intermediate Frequency Sound 41.25MHz Color Sub Carrier 42.17MHz Automatic Gain Control Reverse AGC Audio Sound Multiplex System Samsung Electronics...
Page 52
1'st Field V Flyback Period Line 21 2'nd Field Line 284 Fig. 2-1 Video Signal COLOR BURST 16BIT NRZ DATA CLOCK RUN IN START BIT Line 21 0 IRE Fig. 2-2 Caption Data Samsung Electronics...
Page 53
SIGNAL ELECTRON BEAM DIRECTION COPPER POWER FROM SPIRAL COIL ELECTRON BEAM COIL MODULATION COIL MODULATION MAGNETIC FIELD CURRENT Fig. 2-4 Velocity Modulation Coil Fig. 2-5 The velocity-modulation circuit detects and smooths the pulse-amplitude differentials of the Deflection waveform. Samsung Electronics...