Advertisement
Quick Links
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. Operational Safety
p WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
p WARNING! Disconnect from air supply before changing accessories or servicing.
Maintain the polisher in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
3
invalidate the warranty.
Use in a suitable clean and tidy work area and ensure there is adequate lighting.
3
Before each use check pads for condition. If worn or damaged replace immediately.
3
Ensure the pad rating is the same as, or, greater than the RPM rating of the polisher.
3
Ensure there are no flammable or combustible materials near the work area.
3
p WARNING! Always wear approved eye or face and hand protection when operating the polisher.
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back
3
long hair.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the polisher. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
3
p WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure is no
more than 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
3
that all connections are secure.
Prolonged exposure to vibration from this polisher poses a health risk. It is the owner's responsibility to
3
correctly assess the potential hazard and issue guidelines for safe periods of use and offer suitable
protective equipment.
DO NOT use the polisher for a task it is not designed to perform.
7
DO NOT operate polisher if any parts are damaged or missing as this may cause failure and/or personal
7
injury.
p WARNING! DO NOT polish any materials containing asbestos.
DO NOT carry the polisher by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to the polisher, let the polisher do the work.
7
DO NOT place air line attachments close to your face and DO NOT point at other persons or animals.
7
DO NOT operate polisher when you are tired or under the influence of alcohol, drugs or intoxicating
7
medication.
DO NOT use polisher where there are flammable
7
liquids, solids or gases such as paint solvents and
including waste wiping or cleaning rags etc.
DO NOT carry the polisher with your finger on the
7
power lever.
DO NOT direct air from the air hose at yourself or
7
others.
When not in use disconnect from air supply and store
3
in a safe, dry, childproof location.
Original Language Version
INSTRUCTIONS FOR:
AIR ANGLE POLISHER
75mm
SA704
MODEL No:
SA704 Issue: 1 - 12/10/11
fig.1
Advertisement
Related Manuals for Sealey SA704
Summary of Contents for Sealey SA704
- Page 1 SA704 MODEL No: Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
- Page 2 - for full range see pages 650 & 651 of your Sealey catalogue. Ø50mm Noise Pressure......83dB.A Vibration .
- Page 3 5.1. If the air supply does not have an oiler lubricate the air polisher daily with a few drops of good grade air tool oil such as Sealey ATO/500 or ATO/1000, dripped into the air inlet before use. 5.2. Clean the polisher after use and change pads when required.